Anlage zur Akkreditierungsurkunde D-PL nach DIN EN ISO/IEC 17025:2005

Transkript

1 Deutsche Akkreditierungsstelle GmbH Anlage zur Akkreditierungsurkunde D-PL nach DIN EN ISO/IEC 17025:2005 Gültigkeitsdauer: bis Ausstellungsdatum: Urkundeninhaber: CSA Group Bayern GmbH Ohmstraße 1-4, Straßkirchen Prüfungen in den Bereichen: Elektromagnetische Verträglichkeit (EMV) und Funk Sicherheit elektrischer Betriebsmittel (SEB) und Umweltsimulation Telekommunikation verwendete Abkürzungen: siehe letzte Seite Dem Laboratorium ist, ohne dass es einer vorherigen Information und Zustimmung der DAkkS bedarf, die Anwendung der hier aufgeführten genormten Prüfverfahren mit unterschiedlichen Ausgabeständen der Normen gestattet. EMV IEC : 2008 EN : 2009 DIN EN VDE : 2009 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity EMV IEC : A1: A2: 2010 EN : A1: A2: 2010 DIN EN VDE : 2011 Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test Seite 1 von 95

2 EMV IEC : A1: 2011 EN : A1: 2010 DIN EN VDE :2010 EMV IEC : 2005 EN : 2006 DIN EN VDE : 2007 Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test EMV IEC : 2008 EN : 2009 DIN EN VDE : 2009 Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields EMV IEC : 2009 EN : 2010 DIN EN VDE : 2010 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test EMV IEC :1993 +A1:2000 EN : A1:2001 DIN EN VDE :2001 EMV IEC : A1:2000 EN : A1:2001 DIN EN VDE : 2001 Elektromagnetische Verträglichkeit (EMV) Teil 4-9: Prüf- und Messverfahren; Prüfung der Störfestigkeit gegen impulsförmige Magnetfelder. Electromagnetic compatibility (EMC) - Part 4-10: Testing and measurement techniques - Damped oscillatory magnetic field immunity test Gültigkeitsdauer: bis Ausstellungsdatum: Seite 2 von 95

3 EMV IEC : 2004 EN : 2004 DIN EN VDE : 2005 Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests EMV IEC : 2006 EN : 2006 DIN EN VDE : 2007 Electromagnetic compatibility (EMC) - Part 4-12: Testing and measurement techniques - Ring wave immunity test EMV IEC : A1: 2009 EN : A1: 2009 DIN EN VDE : 2010 Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity tests EMV IEC : A1: A2: 2009 EN : A1: A2: 2009 DIN EN VDE : 2010 EMV IEC : A1: A2: 2009 EN : A1: A2: 2011 DIN EN VDE : 2011 Electromagnetic compatibility (EMC) - Part 4-14: Testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase Electromagnetic compatibility (EMC) - Part 4-16: Testing and measurement techniques - Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 khz Gültigkeitsdauer: bis Ausstellungsdatum: Seite 3 von 95

4 EMV IEC Ed. 1.2: 2009 EN : 1999/A2: 2009 DIN EN /A2: 2009 VDE /A2: 2009 EMV IEC : A1: 2010 EN : 2007/A1: 2010 DIN EN /A1 VDE /A1: 2011 EMV IEC : 2010 EN : 2010 DIN EN Berichtigung 1 VDE Berichtigung 1: 2012 Electromagnetic compatibility (EMC) - Part 4-17: Testing and measurement techniques - Ripple on d.c. input power port immunity test Electromagnetic compatibility (EMC) - Part 4-18: Testing and measurement techniques - Damped oscillatory wave immunity test Electromagnetic compatibility (EMC) - Part 4-20: Testing and measurement techniques - Emission and immunity testing in transverse electromagnetic (TEM) waveguides EMV IEC : A1: 2009 EN : A1: 2009 DIN EN VDE : 2009 Electromagnetic compatibility (EMC) - Part 4-27: Testing and measurement techniques - Unbalance, immunity test for equipment with input current not exceeding 16 A per phase EMV IEC : A1: A2: 2009 EN : 2000 DIN EN VDE : 2009 Electromagnetic compatibility (EMC) - Part 4-28: Testing and measurement techniques - Variation of power frequency, immunity test for equipment with input current not exceeding 16 A per phase Gültigkeitsdauer: bis Ausstellungsdatum: Seite 4 von 95

5 EMV IEC : 2000 EN : 2000 DIN EN VDE : 2001 Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests EMV EN :2009 IEC :2008 VDE : Electromagnetic compatibility (EMC) Part 4-30 Power quality measurement methods EMV EN : 2011 DIN EN VDE : 2012 Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz - Part 1: General requirements, frequency bands and electromagnetic disturbances EMV EN : A1: 2005 DIN EN VDE : 2006 Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz - Part 2-1: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 khz to 148,5 khz and intended for use in residential, commercial and light industrial environments EMV EN : A1: 2005 DIN EN VDE : 2006 Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz - Part 2-2: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 khz to 148,5 khz and intended for use in industrial environments Gültigkeitsdauer: bis Ausstellungsdatum: Seite 5 von 95

6 EMV EN : A1: 2005 DIN EN VDE : 2006 Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz - Part 2-3: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 3 khz to 95 khz and intended for use by electricity suppliers and distributors EMV EN : 2006 Cable networks for television signals, sound signals and interactive services - Part 2: Electromagnetic compatibility for equipment EMV EN : A1: A2: 2007 DIN EN VDE : 2007 EMV EN : 1995 DIN EN VDE : 1996 Home and Building Electronic Systems (HBES) - Part 2-2: System overview - General technical requirements Uninterruptible Power Systems (UPS) Part 2: EMC requirements EMV EN : 2006 DIN EN VDE : 2007 EMV EN : 2006 DIN EN VDE : 2007 Railway applications - Electromagnetic compatibility - Part 1: General Railway applications - Electromagnetic compatibility - Part 2: Emission of the whole railway system to the outside world Gültigkeitsdauer: bis Ausstellungsdatum: Seite 6 von 95

7 EMV EN : 2006 DIN EN VDE : 2007 Railway applications - Electromagnetic compatibility - Part 3-1: Rolling stock - Train and complete vehicle EMV EN : 2006 DIN EN VDE :2007 Railway applications - Electromagnetic compatibility - Part 3-2: Rolling stock - Apparatus EMV EN : 2006 DIN EN VDE : 2007 Railway applications - Electromagnetic compatibility - Part 4: Emission and immunity of the signalling and telecommunications apparatus EMV EN : 2006 DIN EN VDE : 2007 Railway applications - Electromagnetic compatibility - Part 5: Emission and immunity of fixed power supply installations and apparatus EMV EN : 2011 DIN EN VDE : 2012 Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems EMV EN 50148: 1995 DIN EN 50148: 1996 EMV EN 50155: 2007 DIN EN VDE : 2008 EMV EN 50199: 1995 DIN EN VDE : 1996 AS/NZS 3651: 1998 Electronic taximeters Railway applications - Electronic equipment used on rolling stock Electromagnetic compatibility (EMC) Product Standard for arc welding equipment Nur Prüfung bzgl. der elektromagnetischen Phänomene Gültigkeitsdauer: bis Ausstellungsdatum: Seite 7 von 95

8 EMV EN 50240: 2004 Electromagnetic compatibility (EMC) Product Standard for resistance welding equipment EMV EN 50263: 1999 Electromagnetic compatibility (EMC) - Product standard for measuring relays and protection equipment EMV EN 50270: 2006 Electromagnetic compatibility - Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen EMV EN 50293: 2000 DIN EN VDE : 2002 Electromagnetic compatibility - Road traffic signal systems - Product standard EMV EN 50364: 2010 DIN EN VDE : 2010 Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications EMV EN 50357:: 2001 DIN EN 50357: 2002 Evaluation of human exposure to electromagnetic fields from devices used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications Gültigkeitsdauer: bis Ausstellungsdatum: Seite 8 von 95

9 EMV EN : 2005 DIN EN VDE : 2006 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission EMV EN : 2003 DIN EN VDE : 2003 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity; EMV EN 50428: A1: A2:2009 DIN EN VDE :2010 EMV EN : 2006 DIN EN VDE : 2007 Schalter für Haushalt und ähnliche ortsfeste elektrische Installationen Ergänzungsnorm Schalter und ähnliches Installationsmaterial zur Verwendung in elektronischer Systemtechnik für Heim und Gebäude (ESHG). Electricity metering equipment (a.c.) - Part 1: General requirements, tests and test conditions - Metering equipment (class indexes A, B and C) Nur Prüfung bzgl. der elektromagnetischen Phänomene EMV EN :2010 Allgemeine Anforderungen an die Elektrische Systemtechnik für Heim und Gebäude (ESHG) und an Systeme der Gebäudeautomation (GA) - Teil 5-1: EMV- Anforderungen, Bedingungen und Prüfungen EMV EN :2010 Allgemeine Anforderungen an die Elektrische Systemtechnik für Heim und Gebäude (ESHG) und an Systeme der Gebäudeautomation (GA) - Teil 5-2: EMV- Anforderungen an ESHG/GA für den Gebrauch in Wohnbereichen, Geschäftsund Gewerbebereichen sowie in Kleinbetrieben Gültigkeitsdauer: bis Ausstellungsdatum: Seite 9 von 95

10 EMV EN :2010 Allgemeine Anforderungen an die Elektrische Systemtechnik für Heim und Gebäude (ESHG) und an Systeme der Gebäudeautomation (GA) - Teil 5-3: EMV- Anforderungen an ESHG/GA für den Gebrauch im Industriebereich EMV EN 13309: 2010 DIN EN 13309: 2010 Construction machinery - Electromagnetic compatibility of machines with internal power supply EMV EN 14010: A1: 2009 DIN EN 14010: 2009 Safety of machinery - Equipment for power driven parking of motor vehicles - Safety and EMC requirements for design, manufacturing, erection and commissioning stages Nur Prüfung bzgl. der elektromagnetischen Phänomene EMV IEC/CISPR 11: A1: 2010 EN 55011: A1: 2010 DIN EN VDE : 2011 CAN/CSA CEI/IEC CISPR 11: 2004 EMV IEC/CISPR 12: A1: 2009 EN 55012: A1: 2009 DIN EN 55012: VDE : 2010 Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers Gültigkeitsdauer: bis Ausstellungsdatum: Seite 10 von 95

11 EMV IEC/CISPR 13: 2009 EN A1: A2: 2006 DIN EN VDE : 2006 AS/NZS CISPR 13: 2004 CNS 13439: 2004 EMV IEC/CISPR 14-1 : A1: A2: 2011 EN : A1: A2: 2011 DIN EN VDE : 2012 EMV IEC/CISPR 14-2 : A1: A2: 2008 EN : A1: A2: 2008 DIN EN VDE : 2009 EMV IEC/CISPR 15: A1: A2: 2008 EN 55015: A1: A2: 2009 DIN EN VDE : 2009 EMV CISPR 18-2:1986 DIN VDE 0873 Beiblatt 2 :1990 Sound and television broadcast receivers and associated equipment - Radio disturbance characteristics - Limits and methods of measurement Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 2: Immunity - Product family standard Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment Die spezifischen Eigenschaften der von Hochspannungsfreileitungen und -anlagen verursachten Funkstörungen; Teil2: Messverfahren und Methoden zur Bestimmung von Grenzwerten. Gültigkeitsdauer: bis Ausstellungsdatum: Seite 11 von 95

12 EMV CISPR 18-3:1986 DIN VDE 0873 Beiblatt 3 :1991 EMV IEC/CISPR 20: 2006 EN 55020: 2007 DIN EN VDE : 2007 Die spezifischen Eigenschaften der von Hochspannungsfreileitungen und -anlagen verursachten Funkstörungen; Teil3: Leitfaden zur Minimierung von Funkstörungen. Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement EMV IEC/CISPR 22: 2008 EN 55022: 2010 DIN EN VDE : 2011 CAN/CSA CEI/IEC CISPR 22: 2010 AS/NZS CISPR 22: 2009 CNS 13438: 1997 ICES-003: 2012 EMV IEC/CISPR 24: 2010 EN 55024: 2010 DIN EN VDE : 2011 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement (CISPR 22:2008, modified) Information technology equipment - Immunity characteristics - Limits and methods of measurement EMV IEC/CISPR 32: 2012 Electromagnetic compatibility of multimedia equipment - Emission requirements EMV IEC/CISPR 32: 2012 Corrigendum 1 EMV IEC/CISPR 32: 2012 Corrigendum 2 Electromagnetic compatibility of multimedia equipment - Emission requirements Electromagnetic compatibility of multimedia equipment - Emission requirements Gültigkeitsdauer: bis Ausstellungsdatum: Seite 12 von 95

13 EMV EN : 2009 DIN EN VDE : 2010 Electromagnetic compatibility - Product family standard for audio, video, audiovisual and entertainment lighting control apparatus for professional use - Part 1: Emissions EMV EN : 2009 DIN EN VDE : 2010 Electromagnetic compatibility - Product family standard for audio, video, audiovisual and entertainment lighting control apparatus for professional use - Part 2: Immunity EMV EN : 2010 DIN EN VDE : 2011 Rotating electrical machines - Part 1: Rating and performance EMV EN : 2011 DIN EN VDE : 2012 Electroacoustics - Hearing aids - Part 13: Electromagnetic compatibility (EMC) EMV IEC : 1996 EN : 1998 DIN EN VDE : 1999 Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems EMV IEC : 1999 EN : 1999 Low-voltage switchgear and controlgear assemblies - Part 1: Type- tested and partially type-tested assemblies EMV IEC 521: 1988 EN 60521: 1995 DIN EN 60521: VDE0418 Teil 14: 1995 Classes 0,5, 1 and 2 alternating-current watthour meters Gültigkeitsdauer: bis Ausstellungsdatum: Seite 13 von 95

14 EMV EN : 2004/A12: 2010 Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches EMV IEC : 2006 EN : 2006 DIN EN VDE : 2007 Switches for household and similar fixed electrical installations - Part 2-2: Particular requirements - Electromagnetic remotecontrol switches (RCS) EMV IEC : 2006 EN : 2006 DIN EN VDE : 2007 EMV EN 60687: 1992 DIN EN VDE0418 Teil 8: 1994 Switches for household and similar fixed electrical installations - Part 2-3: Particular requirements - Time delay switches (TDS) Alternating current static watt-hour meters for active energy (classes 0,2 S and 0,5 S) EMV IEC : 2010, modified EMV EN : 2011 DIN EN : 2011 VDE : 2012 CAN/CSA E : 2013 Automatic electrical controls for household and similar use - Part 1: General requirements Automatic electrical controls for household and similar use - Part 1: General requirements (Adopted IEC/CEI :2010, fourth edition, , with Canadian deviations) only EMC parts Gültigkeitsdauer: bis Ausstellungsdatum: Seite 14 von 95

15 EMV IEC :2000, modified +A1: 2004, modified +A2: 2008, modified EN : A1: A11: A2: 2010 DIN EN VDE : 2011 EMV IEC : 2007, modified EN : 2008 DIN EN VDE : 2009 Automatic electrical controls for household and similar use - Part 2-5: Particular requirements for automatic electrical burner control systems Automatic electrical controls for household and similar use - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements EMV EN : 2010/AC: 2011 DIN EN Berichtigung 1 VDE Berichtigung 1: 2012 EMV IEC : 2000, modified +A1: 2002, modified EN : A1: 2003 DIN EN VDE : 2004 EMV IEC : 2008, modified EN : 2010 DIN EN VDE : 2011 Automatic electrical controls for household and similar use - Part 2-7: Particular requirements for timers and time switches Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls Gültigkeitsdauer: bis Ausstellungsdatum: Seite 15 von 95

16 EMV IEC : 2006 EN : 2008 DIN EN VDE : 2008 Automatic electrical controls for household and similar use - Part 2-11: Particular requirements for energy regulators EMV IEC : : 2006, modified EN : 2008 DIN EN VDE : 2008 EMV IEC : 1995, modified +A1: A2:2007, modified EN : A1: A11: A2: 2008 DIN EN VDE : 2009 EMV IEC :1997, modified EN : 1999 DIN EN VDE0631 Teil 2-18: 2000 Automatic electrical controls for household and similar use - Part 2-13: Particular requirements for humidity sensing controls Automatic electrical controls for household and similar use - Part 2-14: Particular requirements for electric actuators Automatic electrical controls for household and similar use - Part 2-18: Particular requirements for automatic electrical water and air flow sensing controls, including mechanical requirements EMV IEC : 1995 EN : 1996 DIN EN : 1997 Telecontrol equipment and systems - Part 2: Operating conditions; section 1: Power supply and electromagnetic compatibility Gültigkeitsdauer: bis Ausstellungsdatum: Seite 16 von 95

17 EMV IEC 60945: 2002 EN 60945: 2002 DIN EN 60945: 2003 Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results EMV IEC : A1: 2010 EN : : A1: 2011 DIN EN VDE : 2011 EMV IEC : A1: 2009 EN : A1: 2009 DIN EN VDE : 2010 EMV IEC : A1: 2012 EN : A1: 2012 DIN EN VDE : 2012 EMV IEC : 2009 EN : 2010 DIN EN VDE : 2011 Low-voltage switchgear and controlgear - Part 1: General rules Note 6 Low-voltage switchgear and controlgear - Part 2: Circuit-breakers Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switchdisconnectors and fuse-combination units Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motorstarters Gültigkeitsdauer: bis Ausstellungsdatum: Seite 17 von 95

18 EMV IEC : A1: A2: 2006 EN : A1: A2: 2006 DIN EN VDE : 2007 EMV IEC : A1: A2: 2011 EN : A1: A2: 2011 DIN EN VDE : 2012 EMV IEC : A1: 2009 EN : A1: 2009 DIN EN VDE : 2010 EMV (IEC : 2007 EN : 2007 DIN EN VDE : 2008 EMV IEC : 2007 EN : A1: 2005 DIN EN VDE : 2005 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor-starters - AC semiconductor controllers and contactors for non-motor loads Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices Low-voltage switchgear and controlgear - Part 5-2: Control circuit devices and switching elements - Proximity switches Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDF) Gültigkeitsdauer: bis Ausstellungsdatum: Seite 18 von 95

19 EMV IEC : 1999 EN : 2000 DIN EN VDE : 2000 Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements, DC interface for proximity sensors and switching amplifiers (NAMUR) EMV IEC : 2003 EN : 2003 DIN EN VDE : 2004 Low-voltage switchgear and controlgear - Part 5-7: Control circuit devices and switching elements - Requirements for proximity devices with analogue output EMV IEC : 2005 EN : 2005 DIN EN VDE : 2006 EMV IEC : A1: 2007 EN : A1: 2007 DIN EN VDE : 2007 EMV IEC : A1: 2006 EN : A1: 2006 DIN EN VDE : 2007 EMV IEC : 2007 EN : 2007 DIN EN VDE : 2008 Low-voltage switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer switching equipment Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS) Low-voltage switchgear and controlgear - Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements Gültigkeitsdauer: bis Ausstellungsdatum: Seite 19 von 95

20 EMV IEC : A1: A2: 2009 EN : A1: A2: 2009 DIN EN VDE : 2010 EMV IEC : amm. EN : amm. DIN EN VDE : 2009 Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current <= 16 A per phase) Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <=16 A per phase and not subject to conditional connection EMV IEC : 2000 EN : 2000 DIN EN VDE : 2001 Electromagnetic compatibility (EMC) - Part 3-11: Limits; Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems; Equipment with rated current <= 75 A and subject to conditional connection EMV IEC : 2011 EN : 2011 DIN EN VDE : 2012 Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and <= 75 A per phase EMV IEC : 2005 EN : 2007 DIN EN VDE : 2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments Gültigkeitsdauer: bis Ausstellungsdatum: Seite 20 von 95

21 EMV IEC : 2005 EN : 2005 DIN EN VDE : 2006 EMV IEC : A1: 2010 EN : A1: 2011 DIN EN VDE : 2011 AS/NZS : 1999 EMV IEC : A1: 2010 EN : A1: 2011 DIN EN VDE : 2011 AS/NZS : 1999 EMV IEC : A1: 2002 EN : A12: 2009 DIN EN VDE : 2010 EMV IEC : A1: 2002, modified EN : A11: A12: A13: 2009 EMV IEC 61036: A1: 2000 EN 61036: A1: 2000 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and lightindustrial environments Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's) - Part 1: General rules Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO's) - Part 1: General rules Alternating current static watt-hour meters for active energy (classes 1 and 2) Gültigkeitsdauer: bis Ausstellungsdatum: Seite 21 von 95

22 EMV IEC 61037: A1: A2: 1998 EN 61037: A1: A2: 1998 EMV IEC 61038: A1: A2: 1998 EN 61038: A1: A2: 1998 EMV IEC : 2007 EN : 2007 DIN EN VDE : 2008 EMV IEC : 2000 EN : 2000 DIN EN VDE : 2001 Electronic ripple control receivers for tariff and load control Electricity metering Tariff and load control particular requirements for time switches Programmable controllers - Part 2: Equipment requirements and tests Low-voltage power supplies DC output - Part 3: Electromagnetic compatibility (EMC) EMV IEC 1268: 1995 EN 61268: 1996 Alternating current static var hour meters for reactive energy EMV IEC 61326: A1: A2: E & F: 2002 EN 61326: A1: A2: A3: 2003 DIN EN 61326: 2004 Electrical equipment for measurement, control and laboratory use EMC requirements Gültigkeitsdauer: bis Ausstellungsdatum: Seite 22 von 95

23 EMV IEC : 2005 EN : 2006 DIN EN VDE : 2006 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements EMV IEC : 2005 EN : 2006 DIN EN VDE : 2006 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-1: Particular requirements - Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications EMV IEC : 2005 EN : 2006 DIN EN VDE : 2006 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-2: Particular requirements - Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low-voltage distribution systems EMV IEC : 2006 EN : 2006 DIN EN VDE : 2007 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning Gültigkeitsdauer: bis Ausstellungsdatum: Seite 23 von 95

24 EMV IEC : 2006 EN : 2006 DIN EN VDE : 2007 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-4: Particular requirements - Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC and for equipment for insulation fault location according to IEC EMV IEC : 2008 EN : 2008 DIN EN VDE : 2008 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-1: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - General industrial applications EMV IEC : 2008 EN : 2008 DIN EN VDE : 2008 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-2: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - Industrial applications with specified electromagnetic environment EMV IEC : A1: 2010 EN : A1: 2010 DIN EN VDE : 2011 Wind turbines - Part 1: Design requirements Nur Prüfung bzgl. der elektromagnetischen Phänomene Gültigkeitsdauer: bis Ausstellungsdatum: Seite 24 von 95

25 EMV IEC : 2004, mod. +A1:2007 EN : A1: 2008 DIN EN VDE : 2009 EMV IEC : 2001 EN : 2002 DIN EN VDE : 2002 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests Electrical equipment of electric road vehicles - Electric vehicles conductive charging system - Part 2-1: Electric vehicle requirements for conductive connection to an a.c./d.c. supply EMV IEC : 2001 EN : 2002 DIN EN VDE : 2002 Electrical equipment of electric road vehicles - Electric vehicles conductive charging system - Part 2-2: AC electric vehicle charging station EMV IEC 61543: A2: 2005 EN 61543: A11: A12: A2: 2006 DIN EN VDE : 2006 EMV IEC 61547: 2009 EN 61547: amm EN 61547: 2010 DIN EN 61547: VDE : 2010 Residual current-operated protective devices (RCD's) for household and similar use - Electromagnetic compatibility Equipment for general lighting purposes - EMC immunity requirements Nur Prüfung bzgl. der elektromagnetischen Phänomene Gültigkeitsdauer: bis Ausstellungsdatum: Seite 25 von 95

26 EMV EN 617: A1: 2010 DIN EN 617: 2011 Continuous handling equipment and systems - Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers; Nur Prüfung bzgl. der elektromagnetischen Phänomene EMV IEC : A1: 2011 EN : A1: 2012 DIN EN VDE : 2012 EMV IEC : 2011 EN : 2011 DIN EN VDE : 2012 EMV EN 619: A1: 2010 Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods Time relays for industrial and residential use - Part 1: Requirements and tests Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads Nur Prüfung bzgl. der elektromagnetischen Phänomene EMV EN 620: A1: 2010 Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials Nur Prüfung bzgl. der elektromagnetischen Phänomene EMV IEC : 2005 EN : 2006 DIN EN VDE : 2006 Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements Nur Prüfung bzgl. der elektromagnetischen Phänomene Gültigkeitsdauer: bis Ausstellungsdatum: Seite 26 von 95

27 EMV IEC : 2003 EN : 2003 DIN EN VDE : 2003 EMV IEC : 2004 EN : 2004 DIN EN VDE : 2005 Electricity metering equipment (AC) - General requirements, tests and test conditions - Part 11: Metering equipment Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 21: Tariff and load control equipment EMV IEC : 2003 EN : 2003 DIN EN VDE : 2003 Electricity metering equipment (a.c.) - Particular requirements - Part 11: Electromechanical meters for active energy (classes 0,5, 1 and 2) EMV IEC : 2003 EN : 2003 DIN EN VDE : 2003 EMV IEC : 2003 EN : 2003 DIN EN VDE : 2003 Electricity metering equipment (a.c.) - Particular Requirements - Part 21: Static meters for active energy (classes 1 and 2) Electricity metering equipment (a.c.) - Particular requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S) EMV IEC : 2003 EN : 2003 DIN EN VDE : 2003 Electricity metering equipment (a.c.) - Particular requirements - Part 23: Static meters for reactive energy (classes 2 and 3) Gültigkeitsdauer: bis Ausstellungsdatum: Seite 27 von 95

28 EMV IEC :2004 EN : 2004 DIN EN VDE : 2005 EMV IEC : 2004 EN : 2004 DIN EN VDE : 2005 EMV IEC : 2006, modified EN : 2007 DIN EN VDE : 2007 EMV EN 12015: 2004 DIN EN 12015: 2005 Electricity metering (a.c.) - Tariff and load control - Part 11: Particular requirements for electronic ripple control receivers Electricity metering (a.c.) - Tariff and load control - Part 21: Particular requirements for time switches Static Transfer Systems (STS) - Part 2: Electromagnetic compatibility (EMC) requirements Electromagnetic compatibility - Product family standard for lifts, escalators and moving walks - Emission EMV EN 12016: A1: 2008 DIN EN 12016: 2009 Electromagnetic compatibility - Product family standard for lifts, escalators and moving walks - Immunity EMV EN 12895: 2000 DIN EN 12895: 2001 Industrial trucks - Electromagnetic compatibility EMV ISO 14982:1998 EN ISO 14982: 2009 DIN EN ISO 14982: 2009 Agricultural and forestry machines - Electromagnetic compatibility - Test methods and acceptance criteria Gültigkeitsdauer: bis Ausstellungsdatum: Seite 28 von 95

29 EMV EN 298: 2003 DIN EN 298: 2004 Automatic burner control systems for burners and appliances burning gaseous EMV AS/NZS CISPR 11: 2011 Industrial, scientific and medical equipment EMV AS/NZS CISPR 12: 2009 Vehicles, boats and internal combustion engines EMV AS/NZS CISPR 14.1: 2010 Requirements for household appliances, electrical tools and similar apparatus - Emission EMV AS/NZS CISPR 14.2: 2003 Electromagnetic compatibility - Requirements for household appliances electric tools and similar apparatus - Immunity EMV AS/NZS CISPR 15: 2011 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EMV AS/NZS CISPR : 2006 Specification for radio disturbance and immunity measuring apparatus and methods EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods Gültigkeitsdauer: bis Ausstellungsdatum: Seite 29 von 95

30 EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods - - Radio disturbance and immunity measuring apparatus - Ancillary equipment - Disturbance power EMV AS/NZS CISPR : 2009 Specification for radio disturbance and immunity measuring apparatus and methods - Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances EMV AS/NZS CISPR : 2004 EMV AS/NZS CISPR : 2006 Specification for radio disturbance and immunity measuring apparatus and methods - Radio disturbance and immunity measuring apparatus - Antenna calibration test sites for 30 MHz to 1000 MHz Specification for radio disturbance and immunity measuring apparatus and methods - Methods of measurement of disturbances and immunity - Conducted disturbance measurements EMV AS/NZS CISPR : 2012 Specification for radio disturbance and immunity measuring apparatus and methods - Methods of measurement of disturbances and immunity - Measurement of disturbance power EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods - Methods of measurement of disturbances and immunity - Radiated disturbance measurements Gültigkeitsdauer: bis Ausstellungsdatum: Seite 30 von 95

31 EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods - Methods of measurement of disturbances and immunity - Immunity measurements EMV AS/NZS CISPR 16.3: 2004 Specification for radio disturbance and immunity measuring apparatus and methods - CISPR technical reports EMV AS/NZS CISPR : 2006 Specification for radio disturbance and immunity measuring apparatus and methods - Uncertainties, statistics and limit modelling - Uncertainties in standardized EMC tests EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods - Uncertainties, statistics and limit modelling - Uncertainty in EMC measurements EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods - - Uncertainties, statistics and limit modelling - Statistical considerations in the determination of EMC compliance of mass-produced products EMV AS/NZS CISPR : 2004 Specification for radio disturbance and immunity measuring apparatus and methods - Uncertainties, statistics and limit modelling - Statistics of complaints and a model for the calculation of limits Gültigkeitsdauer: bis Ausstellungsdatum: Seite 31 von 95

32 EMV AS/NZS CISPR 20: 2009 Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measure EMV AS/NZS CISPR 22: 2009 Information technology equipment EMV AS/NZS CISPR 24: 2002 Information technology equipment EMV AS/NZS CISPR 25: 2010 Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers EMV EN 45501:1992 4) DIN EN 45501:1992 Metrologische Aspekte nichtselbsttätiger Waagen. Nur Punkt B.3 der Norm. EMV IEC : 2009 EN : 2010 DIN EN VDE : 2011 Semiconductor convertors General requirements and line commutated convertors Part 1-1: Specifications of basic requirements EMV RTCA DO-160G: 2010 Environmental Conditions and Test Procedures for Airborne Equipment EMV Germanischer Llyod: 2012 Rules for classification and construction - Additional rules and guidelines Guidelines for the performance of Type Approvals nur EMV Sektionen (15.0, 16.0, 18.0, 19.0, 20.0, 21.0 und 25.0) Nur Prüfung bzgl. der elektromagnetischen Phänomene EMV ISO : 2011 Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only Gültigkeitsdauer: bis Ausstellungsdatum: Seite 32 von 95

33 EMV ISO : 2007 Road vehicles - Electrical disturbances from conduction and coupling - Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines EMV ISO Technical Corrigendum 1: 2010 Road vehicles - Test methods for electrical disturbances from electrostatic discharge; Technical Corrigendum 1 EMV ISO : 2005 Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 1: General principles and terminology EMV ISO : 2005 Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 2: Off-vehicle radiation sources EMV ISO : 2006 Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Bulk current injection (BCI EMV ISO : Straßenfahrzeuge - Komponentenprüfverfahren für elektrische Störungen durch schmalbandige gestrahlte elektromagnetische Energie - Teil 1: Allgemeines und Definitionen EMV ISO : 2004 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 2: Absorber-lined shielded enclosure Gültigkeitsdauer: bis Ausstellungsdatum: Seite 33 von 95

34 EMV ISO : 2001 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromgnetic energy - Part 3: Transverse electromagnetic (TEM) cell EMV ISO : 2011 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4: Harness excitation methods EMV ISO : 2002 Road vehicles - Component test methods for electrical disturbances by narrowband radiated electromagnetic energy - Part 5: Stripline EMV ISO : 2007 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 8: Immunity to magnetic fields EMV ISO : 2012 Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 9: Portable transmitters EMV DIN : 1992 Elektromagnetische Verträglichkeit (EMV) in Straßenfahrzeugen; Leitungsgeführte impulsförmige Störgrößen auf Versorgungsleitungen in 12-V- und 24-V- Bordnetzen. Gültigkeitsdauer: bis Ausstellungsdatum: Seite 34 von 95

35 EMV DIN : 1991 Elektromagnetische Verträglichkeit (EMV) in Straßenfahrzeugen; Eingekoppelte Störungen auf Geber- und Signalleitungen. EMV DIN : 1990 Elektromagnetische Verträglichkeit (EMV) in Straßenfahrzeugen; Eingestrahlte Störgrößen. EMV IEC/CISPR 25: 2008 EN 55025: 2008 DIN EN VDE : 2009 Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers EMV FCC Part 15: 2012 Radio frequency devices EMV FCC Part 18: 2012 Industrial, scientific and medical equipment EMV FCC/OST MP 5: 1986 FCC Methods of Measurement of Radio Noise Emissions from Industrial, Scientific and Medical Equipment EMV EN 618: A1: 2010 DIN EN 618: 2011 EMV EN : A1: 2011 DIN EN : 2011 EMV EN : Corr A1: 2005 DIN EN VDE : 2006 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors Industrial, commercial and garage doors and gates Product standard - Part 1: Products without fire resistance or smoke control characteristics Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz - Part 2-1: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 khz to 148,5 khz and intended for use in residential, commercial and light industrial environments Nur Prüfung bzgl. der elektromagnetischen Phänomene Nur Prüfung bzgl. der elektromagnetischen Phänomene Gültigkeitsdauer: bis Ausstellungsdatum: Seite 35 von 95

36 EMV IEC : 2006 EN : 2006 DIN EN VDE : 2007 Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-5: Particular requirements Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC EMV EN : V1.4.1 Electromagnetic compatibility and Radio Matters (ERM); Telecommunication network equipment: Electromagnetic Compatibility (EMC) requirements EMV ANSI C63.4: 2009 Methods of Measurement of Radio Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the frequency range of 9 khz to 40 GHz EMV ANSI C63.4: 2003 Methods of Measurement of Radio Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the frequency range of 9 khz to 40 GHz EMV IEC 801-2:1991 Elektromagnetische Verträglichkeit von Betriebsmitteln der Prozessautomation Teil 2: Störfestigkeit gegen die Entladung statischer Elektrizität. EMV IEC 801-3:1984 Elektromagnetische Verträglichkeit von Mess-, Steuer- und Regelteinrichtungen in der industriellen Prozessleittechnik Teil 3: Störfestigkeit gegen elektromagnetische Felder, Anforderungen und Messverfahren. Ab 27 MHz EMV IEC 801-4:1988 Elektromagnetische Verträglichkeit von Mess-Steuer- und Regelteinrichtungen in der industriellen Prozessleittechnik Teil 4: Störfestigkeit gegen schnelle transiente Störgrößen (Burst). Gültigkeitsdauer: bis Ausstellungsdatum: Seite 36 von 95

37 EMV IEC 801-5:1991 Elektromagnetische Verträglichkeit von Mess-Steuer- und Regelteinrichtungen in der industriellen Prozessleittechnik Teil 5: Störfestigkeit gegen Stoßspannung (Surge) EMV ENV 50140:1994 Electromagnetic compatility - Basic immunity standard - Radiated radiofrequency electromagnetic field - Immunity test EMV ENV 50204:1995 Radiated electromagnetic field from digital radio telephones - immunity test EMV AS/NZS 1044:1995 Limits and methods of measurement of radio disturbance characteristics of electrical motor-operated and thermal appliances for household and similar purposes, electric tools and similar electric apparatus. EMV AS/NZS :1995 Specification for radio disturbance and immunity measuring apparatus and methods; Part 1: Radio disturbance and immunity measuring apparatus. EMV AS/NZS :1992 Limits and methods of mearsurement of electromagnetics of industrial, scientific and medical (ISM) radio-frequency equipment; Part 1: General requirements Part 2: Additional requirements for Australia and New Zealand EMV AS/NZS 3548:1995 +A1: A2:1997 Limits and methods of measurement of radio disturbance characteristics of information technology equipment. EMV AS/NZS 4268:2003 Radio equipment and systems Short range devices Limits and methods of measurement Gültigkeitsdauer: bis Ausstellungsdatum: Seite 37 von 95

38 EMV ANSI C63.4: 2014 Methods of Measurement of Radio Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the frequency range of 9 khz to 40 GHz Gültigkeitsdauer: bis Ausstellungsdatum: Seite 38 von 95

39 Funk EN V1.4.1 Electromagnetic compatibility and Radio Spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Part 1: Technical characteristics and methods of measurement Funk EN V1.3.1 Electromagnetic compatibility and Radio Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive Funk EN V1.7.1 Electromagnetic compatibility and Radio Matters (ERM);Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement Funk EN V1.5.1 Electromagnetic compatibility and Radio Matters (ERM);Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive Funk EN V1.2.1 Electromagnetic compatibility and Radio Spectrum Matters (ERM);Angle-modulated Citizens Band radio equipment (CEPT PR 27 Radio Equipment); Part 1: Technical characteristics and methods of measurement Gültigkeitsdauer: bis Ausstellungsdatum: Seite 39 von 95