LED dimmer 6524U

Transkript

1 .00Pos: 2 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Titelblätter/Dimmer/Titelblatt U -- @ 1 === Ende der Liste für Textmarke Cover === LED dimmer 6524U

2 Pos: 4 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Inhaltsverzeichnis (--> Für alle Dokumente @ 1 === Ende der Liste für Textmarke TOC === 1 Safety Intended use Environment Technical data Setup and function Possible combinations Reduction of the connection load (derating) Installation and electrical connection Requirements for the electrician Mounting Electrical connection Commissioning Operation with incandescent lamps LEDi operation

3 Pos: 7 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit @ 1 Pos: 10.2 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise/Hinweis - Umwelt - Hinweis @ 1 Pos: 11 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Safety Pos: 6 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/S Safety Warning Electric voltage! Risk of death and fire due to electrical voltage of 230 V. Work on the 230V supply system may only be performed by authorised electricians! Disconnect the mains power supply prior to installation and/or disassembly! Pos: 8 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/A - F/Bestimmungsgemäßer Intended use Pos: 9 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Bestimmungsgemäßer Gebrauch/Dimmer/Bestimmungsgemaesser Gebrauch - @ 1 The Busch LED dimmer is used for light control in connection with suitable Busch-Jaeger control elements, timers and sensors. Pos: 10.1 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/U Environment Consider the protection of the environment! Used electric and electronic devices must not be disposed of with domestic waste. The device contains valuable raw materials which can be recycled. Therefore, dispose of the device at the appropriate collecting depot. Pos: 10.3 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise/Hinweis - Umwelt - Entsorgung @ 1 All packaging materials and devices bear the markings and test seals for proper disposal. Always dispose of the packaging material and electric devices and their components via the authorized collecting depots and disposal companies. The products meet the legal requirements, in particular the laws governing electronic and electrical devices and the REACH ordinance. (EU Directive 2002/96/EC WEEE and 2002/95/EC RoHS) (EU REACH ordinance and law for the implementation of the ordinance (EC) No.1907/2006)

4 Pos: 13 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Technische Daten/Dimmer/Technische Daten - @ 1 Pos: 14 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Technical data Pos: 12 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/S - T/Technische Technical data General Nominal voltage: 230 V~ ±10%, 50 / 60 Hz Nominal power: W/VA (dependent on ambient temperature) Back-up fuse: electronic Overload protection: electronic Ambient temperature range: 0 C +35 C Protective class: IP 20 Pushbutton input: Maximum cable length 100 m Input voltage 230 V~ ±10% Permissible loads Dimmable retrofit LEDi, 230 V~ Min./max. load 2 W/VA, 25 W/VA 1 Minimum current 8 ma Maximum number 20 Halogen lamps, 230 V~ Min./max. load 10 W, 100 W Minimum current 43 ma Dimmable retrofit LEDi, 12 V~ Min./max. load 4 W/VA, 25 W/VA 1 Minimum current 16 ma Maximum number 20 Dimmable energy-saving lamps Min./max. load 10 W, 100 W Minimum current 43 ma Incandescent lamps, 230 V~ Min./max. load 10 W, 100 W Minimum current 43 ma 1) Connection load for LEDi loads Above a connection load of 25 W/VA, suitable measures must be taken to increase the connection load to a maximum of 100 VA, for example, through the use of harmonic wave filters, in case of a connection of LEDi according to IEC

5 Pos: 18 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Hinweis/Dimmer/Hinweis - Optimiert feur Philips @ 1 Pos: 19 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Setup and function Pos: 15 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/A - F/Aufbau und Setup and function Pos: 16 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Lastarten/Lastarten -- @ 1 The device is intended for the activation and dimming of the following types of loads: Types of load in incandescent lamp operation 230 V~ 230 V~ 230 V~ Halogen lamps, 230 V~ Incandescent lamps, 230 V~ Dimmable halogen energy-saving lamps 1) Types of loads in LEDi operation LEDi 230 V~ LEDi Dimmable retrofit LED lamps (LEDi) 230 V. Dimmable low-voltage retrofit LED lamps (LEDi) on conventional or electronic transformers (L, C) Dimmable low-volt halogen lamps on conventional transformers or electronic transformers (L, C) Pos: 17 /#Neustruktur#/Online-Dokumentation/Lastarten/ZusätzeLastarten - Zusatz - Dimmbare @ 1 1) Use only halogen energy-saving lamps that are labelled as dimmable. Note The device has been optimised for dimming of Philips retrofit LED lamps (LEDi)

6 Pos: 21 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Kombinationsmöglichkeiten/Dimmer/Kombinationsmöglichkeiten - @ 1 Pos: 22 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Setup and function Pos: 20 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/2. Ebene/G Possible combinations 6524 U 6543-xxx-10x 6066-xxx-xxx x xxx-104(M) xxx /11-xxx

7 Pos: 25 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Derating/Derating - Berechnung Nennleistung eleltronische-konventionelle @ 1 Pos: 26 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Derating/Derating - Kurve @ 1 Pos: 27 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Reduction of the connection load (derating) Pos: 23 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/A Reduction of the connection load (derating) Pos: 24 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Derating/Derating - Dimmer (Leistungsminderung 20 prozent bei Einbau in @ 1 The dimmer heats up during operation because part of the connected load is lost and converted into heat. The specified rated power is designed for dimmer installation in a solid masonry wall. When installing the dimmer in a wall made of gas concrete, wood, or plasterboard, the maximum connection load must be reduced by 20%. The connected load must always be reduced when several dimmers are installed one below the other or when other heat sources cause additional heating. In intensely heated-up rooms, the maximum connected load must be reduced according to the diagram. Use the following formula for the calculation of the nominal power: Nominal power = transformer losses* + lamp power * 5% of the nominal transformer power in the case of electronic transformers * 20% of the nominal transformer power in the case of conventional transformers Fig. 1: Derating Unit Meaning % Nominal power C Ambient temperature

8 Pos: 29 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit - Niederspannungs- und 230 @ 1 Pos: 30 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit - Vorgeschaltete Sicherung @ 1 Pos: 32 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Installation and electrical connection Pos: 28 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/M - O/Montage und elektrischer Installation and electrical connection Warning Electric voltage! Risk of death due to electrical voltage of 230 V during short-circuit in the low-voltage line. - Low-voltage and 230 V lines must not be installed together in a flush-mounted socket! Warning Electric voltage! The upstream fuse must be disconnected when working on the lighting system. Pos: 31 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit Requirements for the electrician Warning Electric voltage! Install the device only if you have the necessary electrical engineering knowledge and experience. Incorrect installation endangers your life and that of the user of the electrical system. Incorrect installation can cause serious damage to property, e.g. due to fire. The minimum necessary expert knowledge and requirements for the installation are as follows: Apply the "five safety rules" (DIN VDE 0105, EN 50110): 1. Disconnect from power; 2. Secure against being re-connected; 3. Ensure there is no voltage; 4. Connect to earth and short-circuit; 5. Cover or barricade adjacent live parts. Use suitable personal protective clothing. Use only suitable tools and measuring devices. Check the supply network type (TN system, IT system, TT system) to secure the following power supply conditions (classic connection to ground, protective earthing, necessary additional measures, etc.)

9 Pos: 37 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Anschluss/Dimmer/Anschluss @ 1 Pos: 38 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Installation and electrical connection Pos: 33 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/2. Ebene/M Mounting Pos: 34 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Montage/alle Geräte/Montage - UP-Dosen - DIN @ 1 The device must only be installed in suitable flush-mounted sockets (DIN ). Pos: 35 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/2. Ebene/A - F/Elektrischer Electrical connection Pos: 36 /#Neustruktur#/Online-Dokumentation/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise - Sachschäden/Achtung - Überhitzung bei Transformatorbetrieb - konv. @ 1 Caution Risk of damaging the device due to overheating! - When using transformers, ensure that each transformer is fused individually on the primary side or with a thermal fuse according to the manufacturer's specifications. - Use exclusively wound safety isolating transformers according to DIN VDE L N 16A L 1 ~ N Fig. 2: Standard operation: for possible load types, see chapter " on page 5 If illuminated pushbuttons are used, only push-buttons with a separate N-connection are allowed. (2020 US / 2021 UK). A contact-parallel illumination is not admissible!

10 Commissioning Pos: 39 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/G Commissioning Pos: 40 /#Neustruktur#/Modul-Struktur/Online-Dokumentation/Inbetriebnahme/Dimmer/Inbetriebnahme The minimum brightness is set on the device prior to commissioning. The device has two operating modes. Incandescent lamp operation and LEDi operation. 8.1 Operation with incandescent lamps When operating with incandescent lamps the minimum brightness is fixed. When operating with incandescent lamps the following loads are used: 230 V~ Halogen lamps, 230 V~ 230 V~ 230 V~ Incandescent lamps, 230 V~ Dimmable halogen energy-saving lamps min klick Fig. 3: Minimum brightness when operating with incandescent lamps 1. Set the selector switch for the minimum brightness on the potentiometer on the front of the device. - Turn the potentiometer fully to the left until you can hear a click

11 === Ende der Liste für Textmarke Content === Commissioning 8.2 LEDi operation In LEDi operation the minimum brightness is continuously variable. In LEDi operation the following loads are used: LEDi 230 V~ LEDi Dimmable retrofit LED lamps (LEDi) 230 V~ Dimmable low-voltage retrofit LED lamps (LEDi) on conventional or electronic transformers (L, C) Dimmable low-volt halogen lamps on conventional transformers or electronic transformers (L, C) min Fig. 4: Minimum brightness in LEDi operation 1. Set the minimum brightness on the potentiometer on the front of the device. - Turn the potentiometer in the adjustable range until the desired minimum brightness has been set

12 === Ende der Liste für Textmarke Backcover === Pos: 42 /#Neustruktur#/Online-Dokumentation/Rückseiten (--> Für alle Dokumente <--)Rückseite - Busch-Jaeger - Allgemein ( @ 1 A member of the ABB Group Busch-Jaeger Elektro GmbH PO box Lüdenscheid Freisenbergstraße Lüdenscheid Germany Notice We reserve the right to at all times make technical changes as well as changes to the contents of this document without prior notice. The detailed specifications agreed to at the time of ordering apply to all orders. ABB accepts no responsibility for possible errors or incompleteness in this document info.bje@de.abb.com Central sales service: Phone: +49 (0) Fax: +49 (0) We reserve all rights to this document and the topics and illustrations contained therein. The document and its contents, or extracts thereof, must not be reproduced, transmitted or reused by third parties without prior written consent by ABB. Copyright 2012 Busch-Jaeger Elektro GmbH All rights reserved