8950/8955/8960/ /8909C Control panel v1.0.1

Transkript

1 SIDE-POWER Thruster Systems 8950/8955/8960/ /8909C Control panel v1.0.1 Keep this manual onboard! EN NO Installation and user s manual Installasjon og brukermanual DE Installationsanleitung SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: Fax: sidepower@sleipner.no Made in Norway Sleipner Motor AS 2016

2 Content Product Features... 3 Cut-out dimensions... 3 Installation... 4 Visual wiring diagram... 6 General use... 8 IMPORTANT! This panel will only work with Sidepower electric thrusters with a built in electronic control box and a 4/5 lead control cable system. These panels are waterproof from the front end when correctly installed. However, you must ensure that they can never be submerged in water as this might cause a shortcircuit and thereby causing the thruster to start unintededly. VIKTIG! Dette kontrollpanelet fungerer bare med Sidepower elektriske trustere med integrert elektronisk kontrollboks og 4/5 leders kontrollkabel system. Disse panelene er vantette fra fronten når de er korrekt installert. Men, de må aldri stå slik att de er under vann da dette kan gi en kortslutning som kan føre til selvstarting av trusteren. WICHTIG! Das Panel funktioniert nur mit elektrischen Sidepower Systemen mit integrierter elektronischer Kontrolleinheit und einem Kabelstrang mit 4/5 Leitungen, und ist bei korrektem Einbau an der Vorderseite wasserdicht. Trotzdem muß sichergestellt sein, daß das Panel nicht unter Wasser kommt, da dies zu einem Kurzschluß führen kann. Hierdurch kann es zu einem unbeabsichtigten Start des Thrusters kommen. DECLARATION OF CONFORMITY We, Sleipner Motor AS P.O. Box 519 N-1612 Fredrikstad, Norway declare that this product with accompanying standard remote control systems complies with the essential health and safety requirements according to the Directive 89/336/EEC of 23 May 1989 amended by 92/31/EEC and 93/68/EEC. 2 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

3 Product features b 3 1 n: 2 Ref: Pcs. Parts Deler Teile 1 1 Control panel Kontrolpanel Steuerpanel 2 1 Gasket Pakning Dichtung 3 4 Screws (A4) Skruer (A4) Schraube (A4) 4 4 Corner clips Hjørneklips Eckstück 4b 1 Front ring Frontring Blendenring Cut-out dimensions For control panels 8950 / ,1mm IMPORTANT! Use only attached template! Cut out area: Ø 51,8 mm / 2" 61,0 mm / 2,4" This way Up! Ø52 Ø 3,0 mm / 0,12" WICHTIG! Verwenden Sie nur beigefügten Vorlage! 61,0 mm / 2,4" For control panels 8955/8965/8990 Ø 2,5 mm / 0,10" 50,5mm 111,1mm Cut out area: Ø52 VIKTIG! Bare bruk vedlagt utskjæringsmal! Ø 51,8 mm / 2" 53,0 mm / 2,09" 38,4mm 53,0 mm / 2,09" Cut-Out Template double joystick panel Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

4 Installation EN Installation Find a comfortable position for the panel where it does not obstruct or are obstructed by other controls. Use the enclosed cut-out pattern to mark the area. Cut out the circular area as shown on pattern. If the front surface around your cut out is jaggered or chipped, use a sealant to assist the gasket. A Put the gasket (2) in its designated track in the back face of the panel (1) B Plug the S-link Spur cable into the connector at the rear of panel. Twist the locking ring on the connector clockwise to secure connector. C Put the panel (1) in place and screw in and tighten the four screws (3) D Press gently each of the four corner clips (4) into their corner slot Note! If the thruster runs the opposite way of the panel, swap positions of the grey and the blue control cables in one contact, either by the thruster or by the panel. NO Installasjon Finn en god posisjon for panelet hvor det er lett tilgjengelig og ikke blokkerer andre kontroll enheter. Bruk den medsendte malen til å merke av området, og skjær ut det merkede området. Dersom kantene rundt utskjæringen blir skadet/ujevne på fremsiden må det benyttes en tetningsmasse sammen med pakningen for å sikre god tetning. A Sett inn pakningen (2) i sporet på baksiden av panelet (1). B Koble kontakten sammen med kontroll kabelen fra trusteren. C Koble kontroll signalet til Sidepower automatisk hovedstrømsbryter dersom installert. D Sett panelet (1) inn og skru inn de fire skruene (3). E Press forsiktig inn hver av de fire hjørne klipsene (4) i hvert sitt hjørne. NB! Dersom trusteren skulle gå motsatt vei av panelet, bytt plassering på den grå og den blå kontroll ledning i en kontakt, enten ved trusteren eller ved panelet. 4 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

5 Installation DE Installation Für das Panel eine geeignete Position finden; diese Position muß gut zugänglich sein. Das Panel darf nicht von anderen Teilen blockiert werden. Benutzen Sie die beiliegende Schablone und schneiden Sie das Loch entsprechend der Vorlage aus. Sollte die Schnittkante beschädigt oder uneben sein, bitte zusätzlich zur Dichtung noch Dichtmasse verwenden. A Die Dichtung (2) in die dafür vorgesehene Vertiefung in der Rückseite des Panels einlegen (1). B Den Stecker des Panels mit dem vom Sidepower kommenden Kon trollkabel verbinden. C Falls ein automatischer Hauptschalter installiert ist (optional), diesen mit dem Stecker des Panels verbinden. D Das Panel einsetzen (1) und die vier Schrauben eindrehen (3). E Die vier Eckstücke (4) vorsichtig einsetzen und festpressen. Achtung! Sollte der Sidepower entgegengesetzt zur Panelvorgabe laufen, so sind das graue und das blaue Kabel gegeneinander zu vertauschen; entweder am Sidepower oder am Panel. Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

6 Visual wiring diagram BOW xxM 5-LEAD CONTROL CABLE xxM 5-LEAD CONTROL CABLE STERN LEAD Y-CONNECTOR LEAD Y-CONNECTOR STERN Switch Switch STERN BOW 5A fuse 5A fuse xxM 5-LEAD xxM 5-LEAD CONTROL CABLE CONTROL CABLE xxM 4-LEAD xxM 4-LEAD CONTROL CABLE CONTROL CABLE 6 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

7 Visual wiring diagram (without Automatic Main Switch) BOW xxM 4-LEAD CONTROL CABLE xxM 4-LEAD CONTROL CABLE STERN LEAD Y-CONNECTOR LEAD xa fuse xa fuse Y-CONNECTOR STERN STERN BOW xxM 4-LEAD xxM 4-LEAD CONTROL CABLE CONTROL CABLE Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

8 General use To turn panel ON Turn boat to port To turn panel OFF Turn boat to starboard Bow+Stern Thruster 8 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

9 EN How to use Sidepower thrusters 1. Turn main power switch for the bowthruster on. (Always turn off the main power switch when not onboard.) 2. Please take some time to exercise thruster usage in open water to avoid damages to your boat. 3. Turn the control panel on by pushing both ON buttons on the original Sidepower panel simultaneously. If another type of control is installed, engage the On/Off switch for the bowthruster. 4. Turn the bow in the desired direction by pushing the red button for port movement or the green button for starboard movement. If you have a joystick control, move it in the direction you wish the bow to move. Other controls like footswitches or toggle-switches on the throttle can be used. These are normally logically installed, so by engaging the port control, the bow goes port etc. In case of any doubts, try in open waters first. 5. Depending on the sideways speed of the bow, you must disengage the control device shortly before the bow is in the desired direction, as the boat will continue to move after stopping the bowthruster. How to use a single stern thruster Some boats might however have installed a single stern thruster because of space limitation in the bow. In this case the stern thruster is used in the same way as a single bow thruster (see above) for moving the boat s stern. How to use a bow and stern thruster combined The combination of a bow and stern thruster offers total manoeuvrability to the boat and the opportunity to move the bow and the stern separately from each other. This enables you to move the boat sideways in both directions and to turn the boat around its own axis staying at the same place. Again, if in doubt, try in open water first! If original Sidepower panel is used, the panel shuts off automatically approx 6-9 minutes after last use. Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

10 NO Hvordan bruke Sidepower thruster 1. Skru på hovedstrømmen (skru alltid av hovedstrømmen når du ikke er om bord i båten). 2. Det er fordel om de prøver baugthrusteren på åpent vann den første gangen. 3. Skru på kontrollpanelet ved å trykke inn begge on knappene på Sidepower panelet. Hvis annet en originalt panel brukes må dette skrus på. 4. Snu baugen i ønsket retning ved å trykke rød knapp for babord, og grønn knapp for styrbord. Hvis du har joystickpanel så må stikka dyttes i den retning baugen skal vendes. Andre kontrollenheter som fotbrytere, eller brytere på gass hendel kan også brukes. Disse er vanligvis logisk installert og lette og operere. Ved tvil lønner det seg og prøve på åpent vann først. 5. Avhengig av hvor stor fart baugen får sideveis må thrusteren stoppes før baugen er i riktig posisjon, dette fordi baugen vil fortsette sideveis litt etter thrusteren skruses av. Hvordan bruke en enkel hekkthruster Enkelte båter vil av plassmessige, eller andre hensyn bare installere en hekkthruster. I disse tilfeller brukes hekkthrusteren på samme måte som baugthrusteren. Hvordan bruke hekk og baugthruster kombinert Kombinasjonen av baug og hekkthruster gir en total kontroll over båtens bevegelser p.g.a. muligheten til å bevege hakken og baugen uavhengig av hverandre. Båten kan skyves sidelengs og dreies rundt sin egen akse. Det er også her fordel å prøve ut systemet på åpent vann. Om orginalt Side-Power panel blir brukt så vil dette slås av automatisk etter ca. 6-9 minutter etter siste gang thrusteren ble brukt. 10 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

11 DE Benutzung von Sidepower Thrustern 1. Die Bugschraube über deren Hauptschalter einschalten. Den Hauptschalter immer ausschalten, wenn niemand an Bord ist. 2. Nehmen Sie sich etwas Zeit, um sich auf offenem Gewässer mit der Steuerung de Bugschraube vertraut zu machen. 3. Original Sidepower Panels durch gleichzeitiges Drücken der ON Knöpfe einschalten. Falls eine anderes Panel verwendet wird, den On/Off Schalter für die Bugschraube einschalten. 4. Den Bug in die gewünschte Richtung bewegen; rot / Backbord Knopf für Richtung Backbord, grün / Steuerbord Knopf für Richtung Steuerbord. Bei Verwendung eines Joystick Panels, dieses in die gewünschte Richtung bewegen. Kontrollpanels wie Fuß- und Kippschalter können ebenfalls verwendet werden. Diese sind normalerweise logisch installiert, d.h. der Bug folgt der entsprechenden Panelvorgabe. Bei Unklarheit, zunächst auf offenem Gewässer ausprobieren. 5. Abhängig von der Geschwindigkeit, mit der sich der Bug seitwärts bewegt, muß die Steuerung bereits vor Erreichen des Endpunktes aufhören, da sich der Bug noch etwas in die entsprechende Richtung nachbewegt. Benutzung einer Heckschraube Einige Schiffe haben aufgrund von Platzmangel im Bug stattdessen eine Heckschraube installiert. In diesem Fall ist die Heckschraube wie eine Bugschraube (siehe oben) zu verwenden, um das Heck zu bewegen. Gemeinsame Benutzung von Bug- und Heckschraube Die Kombination von Bug- und Heckschraube bietet die unabhängige Manövrierbarkeit von Bug und Heck. Dies eröffnet die Möglichkeit, das Boot seitwärts in beiden Richtungen oder auf der Stelle um die eigene Achse zu bewegen. Bei Unklarheit, zunächst auf offenem Gewässer ausprobieren. Nach der letzten Benutzung schaltet das Original Side-Power Panel automatisch nach ca. 6-9 Minuten ab. Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

12 EN Warranty Statement 1. The equipment manufactured by Sleipner Motor AS (The Warrantor ) is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years (Leisure Use) or one year (Commercial use) from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferable and covers the product for the specified time period. 4. In case any part of the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) Prepare a detailed written statement of the nature and circumstances of the defect, to the best of the Owner s knowledge, including the date of purchase, the place of purchase, the name and address of the installer, and the Purchaser s name, address and telephone number; (b) The Owner should return the defective part or unit along with the statement referenced in the preceding paragraph to the warrantor, Sleipner Motor AS or an authorized Service Centre, postage/shipping prepaid and at the expense of the Purchaser; (c) If upon the Warrantor s or Authorized Service Centre s examination, the defect is determined to result from defective material or workmanship, the equipment will be repaired or replaced at the Warrantor s option without charge, and returned to the Purchaser at the Warrantor s expense; (d) no refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable to remedy the defect after having a reasonable number of opportunities to do so. Prior to refund of the purchase price, Purchaser must submit a statement in writing from a professional boating equipment supplier that the installation instructions of the Installation and Operation Manual have been complied with and that the defect remains; (e) warranty service shall be performed only by the Warrantor, or an authorized Service Centre, and any attempt to remedy the defect by anyone else shall render this warranty void. 5. There shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse or misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or water immersion except for equipment specifically designed as waterproof. 6. No other express warranty is hereby given and there are no warranties which extend beyond those described in section 4 above. This Warranty is expressly in lieu of any other expressed or implied warranties, including any implied warranty of merchantability, fitness for the ordinary purposes for which such goods are used, or fitness for a particular purpose, and any other obligations on the part of the Warrantor or its employees and representatives. 7. There shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees and representatives for injury to any person or persons, or damage to property, loss of income or profit, or any other consequential or resulting damage or cost which may be claimed to have been incurred through the use or sale of the equipment, including any possible failure or malfunction of the equipment, or part thereof. 8. The Warrantor assumes no liability for incidental or consequential damages of any kind including damages arising from collision with other vessels or objects. 9. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country. 12 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

13 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

14 14 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

15 Control Panel 8950, 8955, 8960, 8965, 8940, 8909C version

16 Worldwide sales and service SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: Fax: The information given in the document was correct at the time it was published. However, Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain. Continuous product improvement may change the product specifications without notice. Therefore, Sleipner Motor AS can not accept liability for any possible differences between product and document.