LED BUILT-IN MODULES. LUGA Shop 2014 PCB FOOD LED Modules COB for Retail Environments lm LUGA SHOP 2014 PCB FOOD

Transkript

1 LED BUILT-IN MODULES LUGA SHOP 2014 PCB FOOD 3000 lm LUGA SHOP 2014 PCB FOOD LED MODULES COB FOR RETAIL ENVIRONMENTS DMS158G**E1 / DMS158P**E1 Typical Applications Integration in reflector luminaires Shop lighting especially for fresh food (bread, fruits, vegetables, meat) LUGA Shop 2014 PCB FOOD LONG SERVICE LIFETIME: 50,000 HOURS (L90; B10) SPECIAL SPECTRUM WITH WIDE COLOUR GAMUT (HiGa) NARROW COLOUR TOLERANCES: 3 STEP MACADAM (INITIAL) 4 STEP MACADAM SHIFT (AFTER 50,000 HRS) istockphoto.com HIGH ELECTRICAL ISOLATION DUE TO CERAMIC COB TECHNOLOGY

2 LUGA SHOP 2014 PCB FOOD Technical Notes LED built-in module for integration into luminaires Dimensions: 27.8x37.3x3.2 mm Light emitting surface (LES): 21 mm Use of external LED constant current driver On-board push-in terminal Electrical Characteristics at t c = 65 C Type Ref. No. Typ. voltage DC Temperature Typ. power consumption 700 ma 1050 ma coefficient 700 ma 1050 ma V V mv/k W W DMS158***E1 All types Voltage and power tolerance: ±10 % Maximum Ratings Exceeding the maximum ratings can lead to reduction of service life or destruction of the modules. Type Operation temperature range Ambient temperature Storage temperature Max. allowed Max. permitted output voltage range at t c -point range range repetitive of operating device C min. C max. C min. C max. C min. C max. peak current (ma) V DMS158***E Optical Characteristics at t c = 65 C Type Ref. No. Colour Correlated colour Typ. luminous flux** and efficiency at Typ. Typ. Phototemperature* 700 ma 1050 ma beam CRI metric K lm lm/w lm lm/w angle ( ) R a code DMS158G30E warm white (special spectrum: HiGa) 830/349 DMS158G40E neutral white (special spectrum: HiGa) 840/349 DMS158P40E "white effect" (special spectrum: HiGa) 740/349 DMS158P19E "pink effect" /349 * Colour tolerance: 3 MacAdam ** Production tolerance of luminous flux and efficiency: ± 10 % Luminous flux values can vary depending on the respective PCB holder system. Minimum order quantity: 80 pcs. Typical Applications DMS158G30E1 DMS158G40E1 DMS158P40E1 DMS158P19E "white effect" "pink effect" Bread & Bakery Fish Meat Meat Fruits Vegetables Drugstore Drapery Cheese LUGA Shop 2014_PCB_Food_GB 2/5 February,

3 LUGA SHOP 2014 PCB FOOD Operating Life at t p = 65 C Product Lumen DMS158***E1 maintenance I F 700 ma I F 1050 ma L90/B10 52,000 hrs. 38,000 hrs. L80/B10 61,000 hrs. 51,000 hrs. L70/B10 70,000 hrs. 59,000 hrs. The specified service life is based on the assumption that the module will exert a surface contact pressure of 28 N and that an optimal thermal connection will be ensured between the entire module and an aluminium heat sink. Internal CCT 2000K 2700K 3000K 3100K 3500K 4000K D B A c d g p Type DMS088 DMS128 DMS158 Internal Ra 80<Ra<90 >90 HiGa Meat/SMeat Typical Light Distribution Curve I (cd/klm) Mechanical Dimensions DMS158***E1 LES Ø tc/tp 4.4± Bins 0,42 0,41 0,40 0, K (Ga30) 0,38 0,37 0,36 0,35 0, K (Ga40) S Meat 0,33 0,32 Meat LUGA Shop 2014_PCB_Food_GB 3/5 February, ,31 0,30 0,35 0,36 0,37 0,38 0,39 0,40 0,41 0,42 0,43 0,44 0,45 0,46 0,47 0,48 0,49 Measurement tolerance x/y: ±

4 LUGA Shop 2014 PCB FOOD Assembly and Safety Information Installation must be carried out under observation of the relevant regulations and standards. The LED modules are designed for operation within a casing or luminaire. Installation must be carried out in a voltage-free state (i.e. disconnection from the mains). The following advice must be observed; non-observance can result in the destruction of the LED assembly modules, fire and/or other hazards. ESD (electrostatic discharge) protection measures must be observed when handling and installing the LED modules. See VS's application notes on ESD protection. LED assembly modules must not be subjected to any undue mechanical stress, e. g.: do not treat as bulk cargo avoid shear and compressive forces during handling and installation do not damage circuit paths do not touch the yellow phosphorus layer The module must be fixed onto a thermally conductive surface. Safe operation only possible by the use of external constant current sources (I max. see table "Electrical Characteristics"). Operation only with power supply units that feature the following protection: Short-circuit protection Overload protection Overheating protection SELV (Safety Extra Low Voltage); U max. 60 V I max. (see table "Maximum Ratings") must not be exceeded. When operating devices will be selected care has been taken to ensure that the maximum values (see table "Maximum Ratings") will not be exceeded. Please ensure the correct polarity of the leads prior to commissioning. Reversed polarity can destroy the modules. The LED modules are equipped with one on-board push-in terminal. Suitable connection leads see next page. Safety regulations acc. to EN (or further standards) has to be observed if the maximum output voltage exceed the permitted touchable value. Measurement tolerances: luminous flux: ± 7 % voltage: ± 3 % CRI: ± 1 % A parallel or serial connection of the modules is not allowed. To ensure problem-free operation, the specified maximum temperature at the t c point (see "Operating Life") must be observed (and measured in accordance with EN ). To satisfy this point, it may be necessary to put measures in place to ensure any heat is dissipated from the PCB to the environment. In the event of outdoor applications or applications in damp locations, care must be taken to protect LED assembly modules against humidity, splashes and jets of water. Any corrosion damage resulting from humidity or contact with condensation will not be recognised as a defect or manufacturing fault. LED assembly modules are not specially protected against foreign bodies or dust. Depending on the type of application, further protection must be ensured to prevent dust and foreign bodies from entering. Operating LED modules in the presence of certain chemical substances or in chemically enriched (aggressive) environments can impair module functionality or even cause total module failure. Detailed information can be found in our "Chemical Incompatibility" PDF on our website The photobiological safety of the LED modules must be classified into risk groups in accordance with EN 62471: general lighting exempt group: DMS158G**E1 / DMS158P**E1 other applications risk group 1: DMS158G**E1 / DMS158P**E1 LUGA Shop 2014_PCB_Food_GB 4/5 February,

5 LUGA SHOP 2014 PCB FOOD Reflectors: ACL-Lichttechnik GmbH Jordan Luxar GmbH & Co. KG JORDAN REFLEKTOREN GmbH & Co. KG LEDIL Heat sinks with active cooling: AVC Nuventix, Inc. Sunon MechaTronix Colliance, Inc. Heat sinks with passive cooling: AVC Fischer Elektronik GmbH & Co. KG Frigo Dynamics MechaTronix LED Constant Current Drivers Please visit our homepage for details for suitable LED constant current drivers: LUGA Shop 2014_PCB_Food_GB 5/5 February,

6 LUGA Shop 2014 PCB Platinenhalter Platinenhalter für LUGA Shop lm bis 5000 lm LUGA Shop-Platinen-Halter, 2-teilig Für LED-Platine LUGA Shop mit LES 15 bzw. 21 mm Abmessungen (ØxH): Ø50x4,8 mm bzw. 7 mm Basishalter: Cr-Ni-Stahl, Kunststoffabdeckung: PBT Befestigung Basishalter: Durchgangslöcher für Schrauben M3, Lochabstand: 35 mm Verp.-Einh.: 500 Stück Typ: Basishalter Best.-Nr.: Typ: Kunststoffabdeckung für Höhe: 4,8 mm Best.-Nr.: weiß Best.-Nr.: schwarz Typ: Kunststoffabdeckung für Höhe: 7 mm Best.-Nr.: weiß Best.-Nr.: schwarz Typ: Kunststoffabdeckung für Höhe: 7 mm Geschlossener Innenring Best.-Nr.: weiß Best.-Nr.: schwarz Die Kunststoffabdeckung wird auf dem Basishalter durch eine 15 -Drehung befestigt, nachdem die Leitungen mit Stecker auf der Platine eingesteckt wurden. Sie verfügt über eine Bajonettbefestigung für Optiken und Reflektoren. Je anch verwendetem thermischen Wärmeleitmaterial und der Leistungsklasse, können die Lebensdauererwartungen von den Angaben im Datenblatt LUGA Shop 2014 PCB abweichen. Anschlussleitungen Für LED-Platine LUGA Shop Leitung: Cu vz, eindrähtig, 0,2 mm² (AWG24), PVC-Isolation, Stecker und Aderendhülsen Best.-Nr.: Länge: 200 mm Best.-Nr.: Länge: 300 mm Best.-Nr.: Länge: 400 mm Platinenhalter_LUGA Shop 2014_PCB_D 1/1 Februar, 2016 Die Werte in diesem Datenblatt können sich aufgrund technischer Innovationen verändern und werden ohne gesonderte Benachrichtigung vorgenommen. Vossloh-Schwabe Deutschland GmbH Hohe Steinert Lüdenscheid Deutschland Tel. +49 (0) 23 51/10 10 Fax +49 (0) 23 51/

7 LUGA Shop 2014 PCB Holder PCB Holder for LUGA Shop 2014 Kit 2000 lm to 5000 lm LUGA Shop Kit holder, 2-pieces For LED PCB LUGA Shop with LES 15 or 21 mm Dimensions (ØxH): Ø50x4.8 mm or 7 mm Base holder: Cr-Ni steel, plastic cover: PBT Fixation base holder: Fixing holes for screws M3 hole distance: 35 mm Packaging unit: 500 pcs. Type: base holder Ref. No.: Type: plastic cover for height: 4.8 mm Ref. No.: white Ref. No.: black Type: plastic cover for height: 7 mm Ref. No.: white Ref. No.: black Type: plastic cover for height: 7 mm Closed inner ring Ref. No.: white Ref. No.: black Once the cables have been inserted in the push-in connector of the PCB, the plastic cover is attached to the base holder with a 15 turn. Plastic cover with bayonett fixing for optics and reflectors. Dependent on the used thermal conductive material and the power classes the expected service life times can differ from the values on the data sheet LUGA Shop 2014 PCB. Connection leads For LED PCB LUGA Shop Lead: Cu tinned, single-core, 0.2 mm² (AWG24), PVC-insulation, plug and ferrule bare end of core Ref. No.: length: 200 mm Ref. No.: length: 300 mm Ref. No.: length: 400 mm PCB Holder_LUGA Shop 2014_PCB_GB 1/1 February,