TABLE OF CONTENTS INTRODUCTION... 2 ENGLISH A1 9/2005. Retain for future use.

Transkript

1 Instruction Bulletin POWERLOGIC Ethernet Gateway EGX100 User s Guide Instrucciones en Español: página 19 Instructions en Français: page 39 Anweisungen auf Deutsch: Seite 59 Retain for future use A1 9/2005 ENGLISH TABLE OF CONTENTS INTRODUCTION... 2 Supported Ethernet Protocols... 2 Hardware... 2 Additional Resources... 3 ACCESSING THE EGX OVER A NETWORK... 3 Logging into the EGX... 3 Logging Out... 3 EGX USER INTERFACE OVERVIEW... 4 SETUP... 5 Ethernet and TCP/IP Settings... 5 Duplicate IP Address Detection... 6 Serial Port... 7 Device List... 8 Master Mode Device List Setup... 8 Slave Mode Device List Setup... 9 User Accounts Web Page Access Modbus TCP/IP Filtering SNMP Parameters DIAGNOSTICS Statistics Interpreting Statistics Read Device Registers FIRMWARE Finding the Firmware Version Getting New Firmware Updating the Firmware File

2 POWERLOGIC Ethernet Gateway A1 Introduction 9/2005 ENGLISH INTRODUCTION This manual is to be used with a POWERLOGIC EGX100 with firmware version 2.0 or higher. For installation information, see the installation manual. The EGX100 is a communications device that provides connectivity between Ethernet (Modbus TCP/IP) and serial line devices, allowing Modbus TCP/IP clients to access information from serial slave devices. It also allows serial master devices to access information from serial slave devices distributed across an Ethernet network. Supported Ethernet Protocols The EGX supports the following Ethernet protocols: Modbus TCP/IP: Modbus TCP/IP is a combination of the Modbus protocol, which provides master-slave communication between devices, and TCP/IP, which provides communications over an Ethernet connection. Modbus TCP/IP is used to exchange data between the EGX and other compatible Modbus TCP/IP devices via TCP port 502. Hypertext Transfer Protocol (HTTP): HTTP is a network protocol that handles the delivery of files and data on the World Wide Web. It provides web server functionality via TCP port 80. Remote configuration of the EGX and the viewing of diagnostic data is possible using a web browser. File Transfer Protocol (FTP): FTP is a network protocol that provides the ability to transfer files over the Internet from one computer to another. FTP is used to transfer firmware updates to the EGX via TCP port 21. Simple Network Management Protocol (SNMP): Based on MIB2 format, SNMP provides the ability to store and send identifying and diagnostic information used for network management purposes via UDP port 161. Address Resolution Protocol (ARP): ARP is used to convert IP addresses to Ethernet addresses. ARP requests are sent by the EGX to determine if its address is a duplicate IP address (see Duplicate IP Address Detection on page 6). Hardware Control power RJ45 Ethernet port LEDs for Ethernet and serial communications Power and Status LED Reset button RS485 serial port Bias, termination, and 2-wire/4-wire jumper switches RS232 serial port (RJ45 connector) Schneider Electric. All Rights Reserved.

3 A1 POWERLOGIC Ethernet Gateway 9/2005 Accessing the EGX Over a Network Additional Resources Documentation: Go to select your country > literature > Communication Devices > Ethernet EGX > Instructional, and then click the manual you want to download. Firmware: Go to select your country > downloads > ECC/EGX Firmware, and then click the firmware file you want to download. NOTE: If you do not have a user name and password, follow the instructions on the web site. ENGLISH ACCESSING THE EGX OVER A NETWORK After you set up the Ethernet parameters (see the installation guide), you can access the EGX over an Ethernet LAN using Internet Explorer 6.0 or higher. Logging into the EGX Action Result 1. Launch Internet Explorer 6.0 or higher. Opens Internet Explorer. 2. In the Address text box, type the address of your EGX ( is the default), then press Enter. Opens the Login dialog box. 3. Type your user name (Administrator is the default) and password (Gateway is the default) into the text boxes, then click OK. 4. Click Setup to access the EGX setup page, or click Diagnostics to access the EGX diagnostics page. Enters the user name and password, then opens the EGX home page. Opens the Setup or Diagnostics pages. Figure 1: The EGX Home Page Menu bar Logging Out We recommend logging out whenever you do not need access to the EGX. To log out of the EGX configuration session, click Log Out to end your session Schneider Electric. All Rights Reserved. 3

4 POWERLOGIC Ethernet Gateway A1 EGX User Interface OVERVIEW 9/2005 ENGLISH EGX USER INTERFACE OVERVIEW The EGX ships with seven pre-installed web pages used for EGX setup and configuration. See Table 1 for a description of each web page. Table 1: EGX static web pages EGX Web Page Description See Page Setup Ethernet & TCP/IP Configure Ethernet and TCP/IP communication settings. 5 Serial Port Set up or change serial communication parameters. 7 Device List Identify serial devices on the daisy chain. 8 User Accounts ➀ Create and edit groups and users. 10 Web Page Access ➀ Select web page access rights for each user group. 11 Modbus TCP/IP Filtering ➀ Set up which IP addresses can access the EGX through 12 Modbus TCP/IP. SNMP Parameters ➀ Enable and configure the Simple Network Management Protocol (SNMP), which allows the EGX to identify itself to network devices requesting SNMP data. 13 Diagnostics Statistics Read Device Registers ➀ Accessible by administrator only Displays diagnostic data used to troubleshoot network problems. This page also contains information about your specific EGX, including the serial number, manufacturing date, and Media Access Control (MAC) address. Allows EGX administrators to read register data from a serial device connected to the EGX Schneider Electric. All Rights Reserved.

5 A1 POWERLOGIC Ethernet Gateway 9/2005 Setup SETUP To access the Setup web page links, click Setup on the EGX menu bar. Ethernet and TCP/IP Settings Action 1. From the Setup page, click Ethernet & TCP/IP. 2. Select your frame format and media type. Contact your network administrator if you do not know. 3. Enter your IP address, subnet mask, and default gateway address assigned to your EGX by your network administrator. Result Opens the Ethernet & TCP/IP page. Selects the frame format and media type. Enters the Ethernet parameters for the EGX. NOTE: If you enter an IP address that is used by another device, you will be prompted to select a new IP address. See Duplicate IP Address Detection on page Click Apply. Updates the EGX Ethernet and TCP/IP settings. * See Table 2 on page 5 for a list of options. ENGLISH NOTE: After making changes to the Ethernet parameters and clicking Apply, the EGX will reboot. Figure 2: Ethernet & TCP/IP Page Table 2: EGX Ethernet and TCP/IP Settings Option Description Setting Frame Format Media Type IP Address Subnet Mask Default Gateway Used to select the format for data sent over an Ethernet connection. Used to define the physical Ethernet connection or media type. Used to enter the static IP address of the EGX. Used to enter the Ethernet IP subnet mask address of your network. Used to enter the gateway (router) IP address used for wide area network (WAN) communications. Ethernet II, SNAP Default: Ethernet II 10T/100Tx Auto 10BaseT-HD 10BaseT-FD 100BaseTX-HD 100BaseTX-FD Default: 10T/100Tx Auto to Default: to Default: to Default: Schneider Electric. All Rights Reserved. 5

6 POWERLOGIC Ethernet Gateway A1 Setup 9/2005 ENGLISH Duplicate IP Address Detection While connected to your network, the EGX publishes its IP address. To avoid any duplicate IP address conflicts, the EGX uses the Address Resolution Protocol (ARP) to see if any other device on your network is using the same IP address. Table 3 below explains how the EGX handles a duplicate IP address when it is detected. Table 3: Duplicate IP Detection Scenarios Scenario Duplicate IP Detected Power/Status LED Boot Process / Power Restore Ethernet Link Detected Reverts to the default EGX IP address, subnet mask, and gateway address. ARP requests are sent every 15 seconds until the IP address is available. When the IP address becomes available, the EGX will use it. Manual Address Change EGX keeps it s previous IP address and displays a message indicating that the IP address is already in use by another device. Receives an ARP request Reverts to the default EGX IP address, subnet mask, and gateway address if a connected device sends four ARP requests for the EGX s IP address. The EGX will send ARP requests every 15 seconds until the IP address is available again. When the IP address becomes available, the EGX will use it. Four blinks, pause pattern Four blinks, pause pattern Schneider Electric. All Rights Reserved.

7 A1 POWERLOGIC Ethernet Gateway 9/2005 Setup Serial Port Action Result 1. From the Setup page, click Serial Port. Opens the Serial Port page. 2. Select your mode, physical interface, transmission mode, baud rate, parity, and response timeout (see Table 4 on page 7). Selects the serial port options. 3. If you select Slave mode, enter the IP addresses for the remotely connected devices (see Table 4 on page 7). Enters the IP addresses of the remote devices. 4. Click Apply. Updates the EGX Serial Port settings. ENGLISH Figure 3: Serial Port Page Table 4: Serial Port Settings Mode Option Description Setting Physical Interface Transmission Mode Used to select how the COM port on the EGX is utilized (master or slave). NOTE: When the Mode is changed, the EGX reboots. Used to select how the EGX serial port is physically wired. Used to select how data is transmitted over a serial connection. Master, Slave Default: Master RS485 4-wire, RS485 2-wire, or RS232 Default: RS485 2-wire Automatic, Modbus ASCII Default: Automatic NOTE: Automatic mode allows you to communicate to Modbus RTU, Jbus, and POWERLOGIC(SY/MAX) slave devices on the same daisy chain. Baud Rate Parity Used to select the data transmission speed over a serial connection. Used to select if data is checked for accuracy using a parity bit. Response Timeout Used to select how long the EGX will wait to receive a response from a serial device. Remote Modbus TCP/IP Connections (Slave mode only) Used to define a list of Modbus TCP/IP addresses for the EGX to use during slave mode communications. 2400, 4800, 9600, 19200, 38400, 56000*, 57600* Default: Even, None Default: Even 0.1 to 20 seconds Default: 3 seconds * Available only if the physical interface and transmission mode is RS232/Modbus ASCII Schneider Electric. All Rights Reserved. 7

8 POWERLOGIC Ethernet Gateway A1 Setup 9/2005 ENGLISH Device List Before you begin, keep in mind the following: For master mode usage of the COM port: Modbus RTU/Jbus devices do not have to be defined in the Device List, but it helps you manage your system. POWERLOGIC protocol (SY/MAX) devices must be defined in the Device List. NOTE: Do not use serial slave addresses 1 or 16 in Automatic transmission mode on a daisy chain with mixed protocols (for example, a single daisy chain with some devices using POWERLOGIC protocol and others using Modbus RTU/Jbus protocol). Master Mode Device List Setup Figure 4: Master Mode Topology Ethernet Connection RS485 connection EGX in master mode Up to 128 serial slave devices using repeaters Serial Slave Devices If you selected Master mode on the Serial Port page, follow the steps below to set up the device list: Action Result 1. From the Setup page, click Device List. Opens the Device List page. 2. Select the number of viewable devices (1 to 128), then click Apply. Selects the number of viewable locations that can be used to define serial slave devices connected to the EGX. 3. In the Local ID text box, type the local ID Enters the local address of the device. (address) of the serial slave device. 4. Select the Protocol. Selects the protocol of the connected device. 5. Repeat steps 3 and 4 until all of the devices Enters all of the connected devices. are entered. 6. Click Apply. Updates the Device List settings. Figure 5: Device List Page in Master Mode Schneider Electric. All Rights Reserved.

9 A1 POWERLOGIC Ethernet Gateway 9/2005 Setup Slave Mode Device List Setup Figure 6: Slave Mode Topology EGX in master mode IP address: EGX in master mode IP address: Serial port slave mode allows serial Modbus master devices to access information from serial slave devices across a TCP/IP network. Figure 6 below illustrates how the devices are connected using the device list settings in Figure 7. Ethernet Connection EGX in slave mode Up to 16 remote IP connections with up to 128 serial slave devices are possible ENGLISH RS485 connection RS485 connection RS232 or RS485 connection Serial Slave Devices Serial Slave Devices If you selected Slave mode on the Serial Port page, follow the steps below to set up the device list: Action Result 1. From the Setup page, click Device List. Opens the Device List page. 2. Select the number of viewable devices (1 to 128), then click Apply. 3. In the Local ID text box, type the local ID (address) of the serial slave device. 4. In the Remote ID text box, type the remote ID (address) of the serial slave device. Selects the number of viewable locations that can be used to define remote Modbus TCP/IP devices. Enters the address of the device that the local Modbus master device will use to access the remote device. Enters the serial slave address of the remotely connected device. 5. Select the Connection. Selects the Modbus TCP/IP address to associate with the remote ID. 6. Repeat steps 3 through 5 until all of the devices are entered. Enters all of the mapping information for the EGX to communicate to the remote devices. 7. Click Apply. Updates the Device List settings. Figure 7: Device List Page in Slave Mode 2005 Schneider Electric. All Rights Reserved. 9

10 POWERLOGIC Ethernet Gateway A1 Setup 9/2005 ENGLISH User Accounts EGX users are assigned user names and passwords. Each user belongs to a group, and each group has access rights to the EGX Web pages assigned by the EGX administrator. NOTE: There are two default user accounts: Administrator (password is Gateway) and Guest (password is Guest). Action 1. From the Setup page, click User Accounts. 2. If you want to change a group name, type a new name in one of the Groups text boxes (the Administrator group name cannot be changed). 3. In the Users section, enter a Name (1 to 24 characters) and Password (0 to 12 characters) for a new user. NOTE: User names and passwords are case-sensitive and can contain only alphanumeric characters. Result Opens the User Accounts page. Enters a new group name. Enters the name and password for a user. 4. Select a group and the default language for Selects the group and language for a user. the new user. 5. Repeat steps 3 and 4 for each additional Continues adding users. user you want to add. 6. Click Apply. Saves all of the user account settings. Table 5: EGX accounts and passwords Account Administrator Guest User-defined accounts (up to 11 accounts possible) Default Password Gateway Guest No default Password is user-defined Figure 8: User Accounts Page Schneider Electric. All Rights Reserved.

11 A1 POWERLOGIC Ethernet Gateway 9/2005 Setup Web Page Access Action 1. From the Setup page, click Web Page Access. 2. In the Ethernet & TCP/IP row, select the access level (None, Read-only, or Full) that each user group will have for the Ethernet & TCP/IP web page. 3. To allow Guest access to the web page, select Read-only under the Guest column. NOTE: If the Guest group is Read-only, other groups may only be set to Read-only or Full. 4. Repeat steps 2 and 3 for the Serial Port, Device List, Statistics, and Read Device Registers rows. Result Opens the Web Page Access page. See Table 6 below for an explanation of access levels for each group. Allows the default Guest group to access the web page. Selects the access level for each web page. 5. Click Apply. Saves the password settings. ENGLISH Table 6: Group Access Group Administrator Guest Three user-defined groups Access Full access to all web pages NOTE: We recommend that you change the default administrator password for system security the first time you log in. Read-only access to selected web pages. Choosing from the following options, the administrator assigns web page access for each group. Access levels are as follows: None: a group has no access to selected web page Read-only: password grants a group read-only access to the selected web page Full: a group has the same access as the Administrator group to the selected web page Figure 9: Web Page Access Page 2005 Schneider Electric. All Rights Reserved. 11

12 POWERLOGIC Ethernet Gateway A1 Setup 9/2005 ENGLISH Modbus TCP/IP Filtering This function allows the administrator to specify Modbus TCP/IP client devices that have or do not have access to serial slave devices connected to the EGX. NOTE: There is an anonymous Modbus TCP/IP address (***.***.***.***) that can be set to Read-only or None. Setting it to Read-only allows any Modbus TCP/IP client not in the filtered list to access serial slave devices with read-only access. Setting it to None blocks all Modbus TCP/IP clients not in the filtered list. Action Result 1. From the Setup page, click Modbus Opens the Modbus TCP/IP Filtering page. TCP/IP Filtering. 2. Check Enable Filtering. Activates filtering. 3. In the IP address column, enter the Modbus TCP/IP client address 4. In the Access Level column, select Readonly or Full. Enters an IP address for a Modbus TCP/IP client that will have access to the serial devices connected to the EGX. Selects the access level for the corresponding IP address. When set to Read-only, only the following Modbus TCP/IP function codes are allowed: Decimal: 1, 2, 3, 4, 7, 8, 11, 12, 17, 20, 24, 43, 100 Hexadecimal: 01, 02, 03, 04, 07, 08, 0B, 0C, 11, 14, 18, 2B, Repeat steps 3 and 4 to add more IP Continues adding IP addresses for filtering. addresses. 6. Click Apply. Saves the Modbus TCP/IP address filtering list. Figure 10: Modbus TCP/IP Filtering Page Schneider Electric. All Rights Reserved.

13 A1 POWERLOGIC Ethernet Gateway 9/2005 Setup SNMP Parameters The EGX supports SNMP, allowing a network administrator to remotely access an EGX with an SNMP manager and view the networking status and diagnostics in the MIB2 format. Action 1. From the Setup page, click SNMP Parameters. 2. Check Enable SNMP to turn ON the simple network management protocol. NOTE: If you uncheck Enable SNMP and click Apply, the EGX will reboot and SNMP functionality will be turned OFF. Result Opens the SNMP Parameters page. Activates SNMP. 3. Enter the system contact, system name, system location, read-only community Enters the SNMP system information and community access names. name, and the read-write community name. 4. Click Apply. Saves the SNMP settings. ENGLISH Figure 11: SNMP Parameters Page 2005 Schneider Electric. All Rights Reserved. 13

14 POWERLOGIC Ethernet Gateway A1 Diagnostics 9/2005 ENGLISH DIAGNOSTICS Statistics To access the Diagnostics web page links, click Diagnostics on the EGX menu bar. Action Result 1. From the Diagnostics page, click Statistics. Opens the Statistics page (see Figure 12). NOTE: The Statistics page displays data based on the mode selected in Serial Port on page View the data. See Interpreting Statistics below. 3. Click Reset. Resets the EGX cumulative diagnostic data to 0. NOTE: This page will show accumulated readings since the EGX was last activated. If power to the EGX is lost, all cumulative values reset to zero. Figure 12: Statistics Page Reading with Serial Port in MASTER MODE Reading with Serial Port in SLAVE MODE Schneider Electric. All Rights Reserved.

15 A1 POWERLOGIC Ethernet Gateway 9/2005 Diagnostics Interpreting Statistics Ethernet Link Status Statistic Frames Transmitted OK Collisions Excessive Collisions Frames Received OK CRC Errors Alignment Errors Frames Too Long Frames Too Short Modbus TCP/IP Frames Sent Frames Received Protocol Errors Active Connections Accumulative Connections Maximum Connections Inbound Read Messages Outbound Read Messages Inbound Write Messages Outbound Write Messages Inbound Reply Messages Outbound Reply Messages Available when the serial port is in Master mode. Description A status string that represents the speed and duplex setting being used to communicate with the linking partner. A counter that increments each time a frame is successfully transmitted. A counter that increments each time a frame is retransmitted due to collision detection. A counter that increments each time a frame is not able to be sent due to reaching the maximum collision status based on the Truncated Binary Exponential Backoff algorithm. A counter that increments each time a frame is successfully received. A counter that increments each time a frame is received that has a checksum/crc that does not match what is calculated. A counter that increments each time a frame is received that has a checksum/crc error and does not end on an 8-bit frame boundary. A counter that increments each time a frame is received that is larger than the allowed maximum size defined in the standards (frames larger than 1518 bytes). A counter that increments each time a frame is received that is smaller than the allowed minimum size defined in the standards (frames smaller than 64 bytes). A counter that increments each time a frame is sent. A counter that increments each time a frame is received. A counter that increments each time an ill-formed message is received. A status value that represents the number of connections that are active at the moment the diagnostics page is refreshed. A maximum of 32 connections are supported. Clicking Active Connections opens a new window with a list of all of the active client connections. A counter that increments each time a connection is made to the EGX. A status value that represents the maximum number of connections that were active at any given moment. A counter that increments each time a read request message is received. A counter that increments each time a read request message is sent. A counter that increments each time a write request message is received. A counter that increments each time a write request message is sent. A counter that increments each time a reply message is received. A counter that increments each time a reply message is sent. ENGLISH Available when the serial port is in Slave mode 2005 Schneider Electric. All Rights Reserved. 15

16 POWERLOGIC Ethernet Gateway A1 Diagnostics 9/2005 Statistic Description ENGLISH Serial Port Frames Sent Frames Received CRC Errors Protocol Errors Timeouts Inbound Read Messages Outbound Read Messages Inbound Write Messages Outbound Write Messages A counter that increments each time a frame is sent. A counter that increments each time a frame is received. A counter that increments each time a message is received that has a CRC that does not match what is calculated. Typically the result of wiring issues. A counter that increments each time an illformed message is received. A counter that increments each time a request message is sent without receiving a corresponding response message within the allowed time. Timeouts are typically the result of configuration errors or a non-responsive device. A counter that increments each time a read request message is received. A counter that increments each time a read request message is sent. A counter that increments each time a write request message is received. A counter that increments each time a write request message is sent. Gateway Information Firmware Version The firmware version that is installed on the EGX. System Idle Time A percentage from 0% to 100% indicating the average processor time that is not being used. MAC Address The unique Ethernet hardware address of an EGX. Serial Number The serial number of the EGX. Model Number The EGX model number (100). Hardware Version EGX hardware version. Manufacture Date Date the EGX was manufactured. Available when the serial port is in Master mode. Available when the serial port is in Slave mode Schneider Electric. All Rights Reserved.

17 A1 POWERLOGIC Ethernet Gateway 9/2005 Diagnostics Read Device Registers Action 1. From the Diagnostics page, click Read Device Registers. 2. Enter the device ID, starting register number, and the number of registers to read. 3. Click Read Holding Registers or Read Input Registers. 4. To change how the data is displayed in the Value column, select Decimal, Hexadecimal, Binary, or ASCII. Result Opens the Read Device Registers page. Enters the values to begin reading registers for the specified device. Displays the values for the listed registers. Selects how the data values are displayed. ENGLISH Table 7: EGX Read Device Register Settings Option Description Default Device ID The address of the device that registers are read. 1 Starting Register The first register to read Number of Registers The number of registers to read (1 to 10). 10 Register column Lists the register numbers Value column Lists the data stored in a register. Decimal, Hexadecimal, Binary, or ASCII options Select an option to specify how the Value column data is displayed. Decimal Figure 13: Read Device Registers Page 2005 Schneider Electric. All Rights Reserved. 17

18 POWERLOGIC Ethernet Gateway A1 Instruction Bulletin 9/2005 ENGLISH FIRMWARE Finding the Firmware Version Firmware on the EGX can be updated using File Transfer Protocol (FTP). Check or with your local sales representative for the latest firmware update. Action Result 1. Log into the EGX. Opens the EGX home page. 2. Locate the firmware version on the bottom-left corner of the page. NOTE: If you recently updated your firmware, press F5 to refresh the web page and update the displayed firmware number. Determines the firmware version of the EGX. 3. Alternatively, you can select Diagnostics > Statistics to find the firmware version in the Gateway Information section. Also determines the firmware version of the EGX. Getting New Firmware Action 1. Launch Internet Explorer, type in the Address text box, then press Enter. Result Opens the POWERLOGIC web site. 2. Click downloads. Opens the downloads page. 3. Enter your user name and password, then Logs into the Technical Support page. click LogIn. 4. Click the ECC/EGX Firmware link. Opens the ECC/EGX Firmware page. 5. Click the firmware file link (eg#####.bin, where ##### is the firmware number), then click Save. Opens the File Download dialog box, then saves the firmware file. Updating the Firmware File Action 1. Launch Internet Explorer, type ftp:// and the IP address of the EGX in the Address text box (for example, ftp:// ), then press Enter. 2. Type the user name Administrator and the administrator password in the text boxes, then click Log On. 3. Locate the saved firmware file on your computer, select it, then press CTRL+C. 4. Right-click in the Internet Explorer window, then click Paste. NOTE: Instead of copying and pasting the firmware file, you can drag-and-drop the firmware file into Internet Explorer. 5. Click the Close button on the Internet Explorer window. Result Opens the Log On As dialog box. Opens an FTP session with the EGX. Copies the firmware file to the clipboard. Copies the firmware to the EGX, and the EGX reboots. Closes Internet Explorer and ends the FTP connection to the EGX. 6. To verify that the firmware version was Verifies the updated firmware version. updated successfully, follow the steps in Finding the Firmware Version on page 18. Schneider Electric Power Monitoring and Control 295 Tech Park Drive, Suite 100 LaVergne, TN USA Tel: +1 (615) Electrical equipment should be installed, operated, serviced, and maintained only by qualified electrical personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material Schneider Electric. All Rights Reserved.

19 Manual de instrucciones Pasarela Ethernet EGX100 de POWERLOGIC Manual del usuario Instructions in English: page 1 Instructions en français: page 39 Anweisungen auf Deutsch: Seite A1 9/2005 Consérvese para futuras consultas. ÍNDICE INTRODUCCIÓN Protocolos Ethernet aceptados Equipo físico Otros recursos ACCESO A LA EGX A TRAVÉS DE UNA RED Conexión a la EGX Desconexión del sistema DESCRIPCIÓN GENERAL DE LA INTERFAZ DE USUARIO DE LA EGX 23 CONFIGURACIÓN Configuración Ethernet y TCP/IP Detección de direcciones IP duplicadas Puerto serie Lista de dispositivos Configuración de la lista de dispositivos en modo maestro Configuración de la lista de dispositivos en modo esclavo Cuentas de usuario Acceso a página Web Filtrado de Modbus TCP/IP Parámetros del SNMP DIAGNÓSTICOS Estadísticas Interpretación de las estadísticas Lectura de registros de dispositivo FIRMWARE Identificación de la versión del firmware Obtención de nuevo firmware Actualización del archivo de firmware ESPAÑOL 19

20 Pasarela Ethernet de POWERLOGIC A1 Introducción 9/2005 INTRODUCCIÓN Este manual debe utilizarse con una POWERLOGIC EGX100 con versión del firmware 2.0 o superior. Para obtener información sobre la instalación, consulte el manual de instalación La EGX100 es un dispositivo de comunicación que ofrece conectividad entre Ethernet (Modbus TCP/IP) y dispositivos en línea serie, permitiendo que los clientes Modbus TCP/IP accedan a la información desde dispositivos esclavos en serie. También permite que los dispositivos maestros serie accedan a información desde dispositivos esclavos en serie distribuidos en una red Ethernet. ESPAÑOL Protocolos Ethernet aceptados La EGX acepta los siguientes protocolos Ethernet: Modbus TCP/IP: Modbus TCP/IP es una combinación del protocolo Modbus, que proporciona comunicación maestro-esclavo entre dispositivos, y TCP/IP, que proporciona comunicación a través de una conexión Ethernet. Se utiliza Modbus TCP/IP para intercambiar datos entre la EGX y otros dispositivos compatibles con Modbus TCP/IP por medio del puerto TCP 502. Protocolo de transferencia de hipertexto (HTTP): HTTP es un protocolo de red que realiza los envíos de archivos y datos en Internet. Proporciona funcionalidad de servidor Web por medio del puerto TCP 80. Con un explorador Web, es posible configurar la EGX y ver los datos de diagnóstico de manera remota. Protocolo de transferencia de archivos (FTP): FTP es un protocolo que ofrece la capacidad de transferir archivos por Internet de un ordenador a otro. Se utiliza FTP para transferir las actualizaciones del firmware a la EGX por medio del puerto TCP 21. Protocolo simple de administración de redes (SNMP): SNMP se basa en el formato MIB2 y proporciona la capacidad de almacenar y enviar información de identificación y diagnóstico utilizada en la red por razones de administración por medio del puerto UDP 161. Protocolo de resolución de dirección (ARP): ARP se utiliza para convertir las direcciones IP en direcciones Ethernet. Las solicitudes de ARP se envían a través de la EGX para determinar si su dirección es el duplicado de una dirección IP (consulte Detección de direcciones IP duplicadas en la página 25) Schneider Electric. Reservados todos los derechos.