Anlage zur Akkreditierungsurkunde D-PL nach DIN EN ISO/IEC 17025:2005

Transkript

1 Deutsche Akkreditierungsstelle GmbH Anlage zur Akkreditierungsurkunde D-PL nach DIN EN ISO/IEC 17025:2005 Gültigkeitsdauer: bis Ausstellungsdatum: Urkundeninhaber: EMCCons DR. RAŠEK GmbH & Co. KG Moggast, Boelwiese 8, Ebermannstadt Prüfungen in den Bereichen: Elektromagnetische Verträglichkeit (), Funkanwendungen, Sicherheit elektrischer Betriebsmittel (SEB) und Umweltprüfungen Innerhalb der mit * gekennzeichneten Akkreditierungsbereiche ist dem Prüflaboratorium, ohne dass es einer vorherigen Information und Zustimmung der DAkkS bedarf, die Anwendung der hier aufgeführten genormten Prüfverfahren mit unterschiedlichen Ausgabeständen der Normen gestattet. Standorte: Moggast: Boelwiese 8, Ebermannstadt (Seite 2-48) Unterleinleiter: Störnhofer Berg 15, Unterleinleiter (Seite 2-48) * flexibler Bereich Seite 2-42 nicht flexibler Bereich Seite Unterleinleiter: Störnhofer Berg 15, Unterleinleiter (Seite ) * flexibler Bereich Seite nicht flexibler Bereich Seite Seite 1 von 116

2 Standort: Moggast: Boelwiese 8, Ebermannstadt Unterleinleiter: Störnhofer Berg 15, Unterleinleiter * flexibler Bereich Seite 2-42 AECTP 250: Electrical; Electromagnetic Environmental Conditions AECTP 500: Electrical; Electromagnetic Environmental Tests 01 ASTM D Standard Test Method for Measuring the Electromagnetic Shielding Effectiveness of Planar Materials EN : 2011 Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz Part 1: General requirements, frequency bands and electromagnetic disturbances EN : Corrigendum A1: 2005 EN : Corrigendum A1: 2005 EN : A1: 2005 Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz; Part 2-1: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 khz to 148,5 khz and intended for use in residential, commercial and light industrial environments Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz; Part 2-2: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 khz to 148,5 khz and intended for use in industrial environments Signalling on low-voltage electrical installations in the frequency range 3 khz to 148,5 khz; Part 2-3: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 3 khz to 95 khz and intended for use by electricity suppliers and distributors Gültigkeitsdauer: bis Ausstellungsdatum: Seite 2 von 116

3 EN : 2012 Cable networks for television signals, sound signals and interactive services; Part 2: Electromagnetic compatibility for equipment EN : A1: A2: 2007 Home and building electronic Systems (HBES); Part 2-2: System overview; General technical requirements EN : 2011 Alarm systems; Part 4: Electromagnetic compatibility; Product family standard: Immunity requirements for components of fire, intruder and social alarm systems EN : 1996 Anechoic chambers; Part 1: Shield attenuation measurement EN : 1996 Anechoic chambers; Part 2: Alternative test site suitability with respect to site attenuation EN 50148: 1995 Electronic taximeters EN 50199: 1995 Electromagnetic compatibility (EMC); Product Standard for arc-welding equipment EN 50263:2000 Electromagnetic compatibility (EMC) - Product standard for measuring relays and protection equipment EN 50270: 2006 Electromagnetic compatibility; Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen EN 50293: 2012 Electromagnetic compatibility; Road traffic signal systems; Product standard EN 50295: 1999 Low-voltage switchgear and control gear; Controller and device interface systems; Actuator Sensor interface (AS-I) EN : 2005 Electromagnetic compatibility (EMC); Product family standard for machine tools; Part 1: Emission EN : 2003 Electromagnetic compatibility (EMC); Product family standard for machine tools; Part 2: Immunity Gültigkeitsdauer: bis Ausstellungsdatum: Seite 3 von 116

4 EN 50498: 2010 Electromagnetic compatibility (EMC); Product family standard for aftermarket electronic equipment in vehicles EN 55011: A1: 2010 EN 55012: A1: 2009 EN 55013: A1: A2: 2006 EN : A1: A2: 2011 EN : Corrigendum A1: A2: 2008 EN 55015: A1: A2: 2009 Industrial, scientific and medical (ISM) radiofrequency equipment; Radio disturbance characteristics; Limits and methods of measurement (CISPR 11: 1997 modified) Vehicles, boats and internal combustion engine driven devices; Radio disturbance characteristics; Limits and methods of measurement for the protection of receivers except those installed in the vehicle; boat; device itself or in adjacent vehicles; boats; devices Sound and television broadcast receivers and associated equipment; Radio disturbance characteristics; Limits and methods of measurement Electromagnetic compatibility; Requirements for household appliances, electric tools and similar apparatus; Part 1: Emission Electromagnetic compatibility; Requirements for household appliances, electric tools and similar apparatus; Part 2: Immunity; Product family standard Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EN 55020: 2007 Sound and television broadcast receivers and associated equipment; Immunity characteristics; Limits and methods of measurement EN 55022: 2010 Information technology equipment; Radio disturbance characteristics; Limits and methods of measurement EN 55024: 2010 Information technology equipment; Immunity characteristics; Limits and methods of measurement Gültigkeitsdauer: bis Ausstellungsdatum: Seite 4 von 116

5 EN : 2009 Electromagnetic compatibility; Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use; Part 1: Emission EN : 2009 Electromagnetic compatibility; Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use; Part 2: Immunity EN : Cor.: 2010 EN : 1998 EN : A1: 2004 DIN EN : Rotating electrical machines; Part 1: Rating and performance Safety of machinery; Electrical equipment of machines; Part 31: Particular safety and EMC requirements for sewing machines, units and systems Low-voltage switchgear and controlgear assemblies; Part 1: Type-tested and partially type-tested assemblies Niederspannungs-Schaltgerätekombinationen; Teil 1: Typgeprüfte und partiell typgeprüfte Kombinationen; Technischer Bericht: Verfahren für die Prüfung unter Störlichtbogenbedingungen EN 60521: 1995 Class 0.5, 1 and 2 alternating-current watthour meters EN : A1: A12: 2010 EN : 2006 / IEC : 2006 EN : 2006 / IEC : 2006 Switches for household and similar fixed electrical installations; Part 2-1: Particular requirements; Electronic switches Switches for household and similar fixed electrical installations; Part 2: Particular requirements; Section 2: Electromagnetic remote-control switches (RCS) Switches for household and similar electrical installations; Part 2-3: Particular requirements; Time-delay switches (TDS) EN 60687: 1992 Alternating current static watt-hour meters for active energy (Classes 0.2 S and 0.5 S) Gültigkeitsdauer: bis Ausstellungsdatum: Seite 5 von 116

6 EN : 2011 Automatic electrical controls for household and similar use; Part 1: General requirements EN : A1: A11: A2: 2010 EN : 2008 EN : 2010 EN : A1: 2003 EN : 2010 EN : 2008 EN : 2008 EN : A1: A11: A2: 2008 EN : 2005 EN : 1996 / IEC : 1995 Automatic electrical controls for household and similar use; Part 2: Particular requirements for automatic electrical burner control systems Automatic electrical controls for household and similar use; Part 2: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements Automatic electrical controls for household and similar use; Part 2: Particular requirements for timers and time switches Automatic electrical controls for household and similar use; Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements Automatic electrical controls for household and similar use; Part 2-9: Particular requirements for temperature sensing controls Automatic electrical controls for household and similar use; Part 2: Particular requirements for energy regulators Automatic electrical controls for household and similar use; Part 2-13: Particular requirements for humidity sensing controls Automatic electrical controls for household and similar use; Part 2: Particular requirements for electric actuators Automatic electrical controls for household and similar use; Part 2: Particular requirements for automatic electrical water and air flow sensing controls, including mechanical requirements Telecontrol equipment and systems; Part 2: Operating conditions; Section 1: Power supply and electromagnetic compatibility Gültigkeitsdauer: bis Ausstellungsdatum: Seite 6 von 116

7 EN 60945: 2002 Marine navigation and radiocommunication equipment and systems; General requirements; Methods of testing and required test results EN : A1: 2011 / IEC : A1: 2010 EN : A1: 2009 / IEC : A1: 2009 EN : A1: 2012 EN : 2010 / IEC : 2009 EN : A1: A2: 2006 / IEC : A1: A2: 2006 EN : A1: A2: 2011 / IEC : A1: A2: 2011 Low-voltage switchgear and controlgear; Part 1: General rules Low-voltage switchgear and controlgear; Part 2: Circuit-breakers Low-voltage switchgear and controlgear; Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units Low-voltage switchgear and controlgear; Part 4-1: Contactors and motor-starters; Section 1: Electromechanical contactors and motor-starters Low-voltage switchgear and controlgear; Part 4-2: Contactors and motor-starters; AC semiconductor motor controllers and starters Low-voltage switchgear and controlgear; Part 4-3: Contactors and motor-starters; AC semiconductor controllers and contactors for non-motor loads EN : Corrigendum A1: 2009 / IEC : A1: 2009 Low-voltage switchgear and controlgear; Part 5-2: Control circuit devices and switching elements; Electromechanical control circuit devices EN : 2007 / IEC : 2007 Low-voltage switchgear and controlgear; Part 5: Control circuit devices and switching elements; Section 2: Proximity switches Gültigkeitsdauer: bis Ausstellungsdatum: Seite 7 von 116

8 EN : A1: Corrigendum 1: 2010 EN : 2002 EN : 2005 EN : A1: 2007 / IEC : A1: 2007 EN : A1: 2006 / IEC : A1: 2006 EN : 2007 / IEC : 2007 EN : A1: A2: 2009 / IEC : A1: A2: 2009 EN : 2008 / IEC : 2008 EN : 2000 / IEC : 2000 Low-voltage switchgear and controlgear; Part 5-3: Control circuit devices and switching elements; Requirements for proximity devices with defined behaviour under fault conditions (PDF) Low-voltage switchgear and controlgear; Part 5-6: Control circuit devices and switching elements; DC interface for proximity sensors and switching amplifiers (NAMUR) Low-voltage switchgear and controlgear; Part 6-1: Multiple function equipment; Section 1: Automatic transfer switching equipment Low-voltage switchgear and controlgear; Part 6-2: Multiple function equipment; Section 2: Control and protective switching devices (or equipment) (CPS) Low-voltage switchgear and controlgear; Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines Arc welding equipment; Part 10: Electromagnetic compatibility (EMC) requirements Electromagnetic compatibility (EMC); Part 3-2: Limits; Limits for harmonic current emissions (equipment input current up to and including 16 A per phase) Electromagnetic compatibility (EMC); Part 3: Limits; Section 3: Limits of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current 16 A per phase Electromagnetic compatibility (EMC); Part 3-11: Limits; Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems; Equipment with rated current 75 A and subject to conditional connection Gültigkeitsdauer: bis Ausstellungsdatum: Seite 8 von 116

9 EN : 1996 / IEC : 1996 EN : 2001 / IEC : 2001 EN : 2007 / IEC : 2005 EN : 2005 / IEC : 2005 EN : 2006/A1: 2010 / IEC : 2007/A1: 2011 Electromagnetic compatibility (EMC); Part 5: Installation and mitigation guidelines; Section 5: Specification of protective devices for HEMP conducted disturbance Electromagnetic compatibility (EMC) - Part 5-7: Installation and mitigation guidelines; Degrees of protection by enclosures against electromagnetic disturbances (EM code) Electromagnetic compatibility (EMC); Part 6-1: Generic standards; Immunity for residential, commercial and light-industrial environments Electromagnetic compatibility (EMC); Part 6-2: Generic standards; Immunity for industrial environments Electromagnetic compatibility (EMC); Part 6-3: Generic standards; Emission standard for residential, commercial and light industrial environments EN : Electromagnetic compatibility (EMC); Part 6-4: A1: 2011 / Generic standards; Emission standard for IEC : industrial environments A1: 2010 EN : 2012 IEC Ed. 3.2: 2013 EN : 2012 IEC Ed. 3.2: 2013 EN 61037: 1992/A2: Corrigendum: Electrical accessories; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB s); Part 1: General rules Electrical accessories; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO s); Part 1: General rules Electricity metering; Tariff and load control; Particular requirements for electronic ripple control receivers Gültigkeitsdauer: bis Ausstellungsdatum: Seite 9 von 116

10 EN 61038: 1992/A2: Corrigendum: EN : 2007 / IEC : 2007 EN : 2000 / IEC : 2000 EN : 2013 / IEC : 2012 EN : 2013 / IEC : 2012 EN : 2013 / IEC : 2012 EN : 2013 / IEC : 2012 Electricity metering; Tariff and load control; Particular requirements for time switches (IEC 61038: 1990 modified) Programmable controllers; Part 2: Equipment requirements and tests Low voltage power supplies, d.c. output; Part 3: Electromagnetic compatibility (EMC) Electrical equipment for measurement, control and laboratory use; EMC requirements; Part 1: General requirements Electrical equipment for measurement, control and laboratory use; EMC requirements; Part 2-1: Particular requirements; Test configurations, operational conditions and performance criteria for sensitive test and measurements equipment for EMC unprotected applications Electrical equipment for measurement, control and laboratory use; EMC requirements; Part 2-2: Particular requirements; Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low-voltage distributions systems. Electrical equipment for measurement, control and laboratory use; EMC requirements; Part 2-3: Particular requirements; Test configurations, operational conditions and performance criteria for transducers with integrated or remote signal conditioning. Gültigkeitsdauer: bis Ausstellungsdatum: Seite 10 von 116

11 EN : 2013 / IEC : 2012 EN : 2013 / IEC : 2012 EN 61543: Corrigendum A11: Corrigendum A12: A2: 2006 / IEC 61543: A2: 2005 EN 61547: 2009 / IEC 61547: 2009 EN : 2006 / IEC : 2006 EN : A1: 2012 / IEC : A1: 2011 EN : 2011 / IEC : 2011 EN : 2006 / IEC : 2005 Electrical equipment for measurement, control and laboratory use; EMC requirements; Part 2-4: Particular requirements; Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC and for equipment for insulation fault location according to IEC Electrical equipment for measurement, control and laboratory use; EMC requirements; Part 2-5: Particular requirements; Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC , CP 3/2. Residual current-operated protective devices (RCD s) for household and similar use; Electromagnetic compatibility Equipment for general lighting purposes; EMC immunity requirements Mechanical structures for electronic equipment; Tests for IEC and IEC Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks Adjustable speed electrical power drive systems; Part 3: EMC product standard including specific test methods Specified time relays for industrial use; Part 1: Requirements and tests Uninterruptible power systems (UPS); Part 2: Electromagnetic compatibility (EMC) requirements Gültigkeitsdauer: bis Ausstellungsdatum: Seite 11 von 116

12 EN : 2003 / IEC : 2003 EN : 2003 / IEC : 2003 EN : 2003 / IEC : 2003 EN : 2003 / IEC : 2003 EN : 2003 / IEC : 2003 Electricity metering equipment (AC); General requirements, tests and test conditions; Part 11: Metering equipment Electricity metering equipment (a.c.); Particular requirements; Part 11: Electromechanical meters for active energy (classes 0.5, 1 and 2) Electricity metering equipment (a.c.); Particular requirements; Part 21: Static meters for active energy (classes 1 and 2) Electricity metering equipment (a.c.); Particular requirements; Part 22: Static meters for active energy (classes 0.2 S and 0.5 S) Electricity metering equipment (a.c.); Particular requirements; Part 23: Static meters for reactive energy (classes 2 and 3) EN 12015: 2004 Electromagnetic compatibility; Product family standard for lifts, escalators and passenger conveyors; Emission EN 12016: A1: 2008 EN 12635: A1: 2008 Electromagnetic compatibility; Product family standard for lifts, escalators and passenger conveyors; Immunity Industrial, commercial and garage doors and gates; Installation and use EN 12895: 2000 Industrial trucks; Electromagnetic compatibility EN 13309: 2010 Construction machinery; Electromagnetic compatibility of machines with internal electrical power supply EN ISO 14982: A1: 2010 Agricultural and forestry machines; Electromagnetic compatibility; Test methods and acceptance criteria Gültigkeitsdauer: bis Ausstellungsdatum: Seite 12 von 116

13 EN V1.6.1: spectrum Matters (ERM); Telecommunication network equipment; Electromagnetic Compatibility (EMC) requirements EN : 1987 Disturbances in supply systems caused by household appliances and similar electrical equipment Part 1: Definitions EN : 1987; DIN VDE : 1987 IEC/TS : IEC/TR : IEC/TR : 2008 IEC/TR : 2008 IEC : EN : 2011 Rückwirkungen in Stromversorgungsnetzen, die durch Haushaltsgeräte und durch ähnliche elektrische Einrichtungen verursacht werden; Teil 1: Begriffe Electromagnetic compatibility (EMC); Part 3-4: Limits; Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 16 A Electromagnetic compatibility (EMC); Part 3: Limits; Section 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16 A Electromagnetic compatibility (EMC) Part 3: Limits; Section 6: Assessment of emission limits for distorting loads in MV and EHV power systems; Basic EMC publication Electromagnetic compatibility (EMC); Part 3: Limits; Section 7: Assessment of emission limits for fluctuating loads in MV and HV power systems; Basic EMC publication Electromagnetic compatibility (EMC); Part 3: Limits; Section 8: Signalling on low-voltage electrical installations; Emission levels, frequency bands and electromagnetic disturbance levels Electromagnetic compatibility (EMC); Part 3-12: Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current < 75 A per phase and subject to restricted connection Gültigkeitsdauer: bis Ausstellungsdatum: Seite 13 von 116

14 EN : 2009 / IEC : 2008 EN : 2006 / IEC : 2006 EN : 2012 / IEC : 2012 EN : 2006 / IEC : 2005 EN : 2009 / IEC : 2008 EN : 2010 / IEC : 2009 Electromagnetic compatibility (EMC); Part 4-2: Testing and measurement techniques; Electrostatic discharge immunity test Electromagnetic compatibility (EMC); Part 4-3: Testing and measurement techniques; Radiated, radio-frequency, electromagnetic field immunity test Electromagnetic compatibility (EMC); Part 4-4: Testing and measurement techniques; Electrical fast transient/burst immunity test Electromagnetic compatibility (EMC); Part 4-5: Testing and measurement techniques; Surge immunity test Electromagnetic compatibility (EMC); Part 4-6: Testing and measurement techniques; Immunity to conducted disturbances, induced by radiofrequency fields Electromagnetic compatibility (EMC); Part 4-8: Testing and measurement techniques; Power frequency magnetic field immunity test EN : Electromagnetic compatibility (EMC); Part 4-9: A1: 2001 / Testing and measurement techniques; Pulse IEC : magnetic field immunity test A1: 2000 EN : Electromagnetic compatibility (EMC); Part 4-10: A1: 2001 / Testing and measurement techniques; Damped IEC : oscillatory magnetic field immunity test A1: 2000 EN : 2004 / IEC : 2004 EN : 2006 / IEC : 2006 Electromagnetic compatibility (EMC); Part 4-11: Testing and measurement techniques; Voltage dips, short interruptions and voltage variations immunity tests Electromagnetic compatibility (EMC); Part 4-12: Testing and measurement techniques; Oscillatory waves immunity test; Basic EMC publication Gültigkeitsdauer: bis Ausstellungsdatum: Seite 14 von 116

15 EN : A1: 2009 / IEC : A1: 2009 EN : A1: A2: 2009 / IEC : A1: A2: 2009 EN : A1: A2: 2011 / IEC : A1: A2: 2011 Electromagnetic compatibility (EMC); Part 4-13: Testing and measurement techniques; Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity tests; Basic EMC publication Electromagnetic compatibility (EMC); Part 4-14: Testing and measurement techniques; Voltage fluctuation immunity test Electromagnetic compatibility (EMC); Part 4-16: Testing and measurement techniques; Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 khz EN : Electromagnetic compatibility (EMC); Part 4-17: A1: 2004 / Testing and measurement techniques; Ripple on IEC : d.c. input power port immunity test A1: 2001 EN : 2010 / IEC : 2010 EN : 2011 / IEC : 2011 EN : 2000 / IEC : 2000 EN : 1997 / IEC : 1997 Electromagnetic compatibility (EMC); Part 4-20: Testing and measurement techniques; Emission and immunity testing in transverse electromagnetic (TEM) waveguides Electromagnetic compatibility (EMC); Part 4-21: Testing and measurement techniques; Reverberation chamber test methods Electromagnetic compatibility (EMC); Part 4-23: Testing and measurement techniques; Test methods for protective devices for HEMP and other radiated disturbances Electromagnetic compatibility (EMC); Part 4: Testing and measurement techniques; Section 24: Test methods for protective devices for HEMP conducted disturbance; Basic EMC publication Gültigkeitsdauer: bis Ausstellungsdatum: Seite 15 von 116

16 EN : A1: 2012 / IEC : A1: 2012 Electromagnetic compatibility (EMC); Part 4-25: Testing and measurement techniques; HEMP immunity test methods for equipment and systems EN : Electromagnetic compatibility (EMC); Part 4-27: A1: 2009 / Testing and measurement techniques; IEC : Unbalance, immunity test A1: 2009 EN : A1: A2: 2009 / IEC : A1: A2: 2009 EN : 2000 / IEC : 2000 EN : 2009 / IEC : 2008 EN : 1996 / IEC : 1996 IEC : IEC : EN 62311: 2008 / IEC 62311: 2007 Electromagnetic compatibility (EMC); Part 4-28: Testing and measurement techniques; Variation of power frequency, immunity test Electromagnetic compatibility (EMC); Part 4-29: Testing and measurement techniques; Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests Electromagnetic compatibility (EMC); Part 4-30: Testing and measurement techniques; Power quality measurement methods Electromagnetic compatibility (EMC); Part 5: Installation and mitigation guidelines; Section 5: Specification of protective devices for HEMP conducted disturbance Electromagnetic compatibility (EMC); Part 6-5: Generic standards; Immunity for power station and substation environments Electromagnetic compatibility (EMC); Part 6-6: Generic standards; HEMP Immunity for indoor equipment Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz Hz) EN 45501: 1992 Metrological aspects of non-automatic weighing instruments Gültigkeitsdauer: bis Ausstellungsdatum: Seite 16 von 116

17 EN : 2006 EN : 2006 EN : 2002 Cable networks for television signals, sound signals and interactive services; Part 8: Electromagnetic compatibility for networks EN : 2006 Railway applications; Electromagnetic compatibility; Part 2: Emission of the whole railway system to the outside world Railway applications; Electromagnetic compatibility; Part 3-1: Rolling stock; Train and complete vehicle Railway applications; Electromagnetic compatibility; Part 3-2: Rolling stock; Apparatus EN : 2006 Railway applications; Electromagnetic compatibility; Part 4: Emission and immunity of the signalling and telecommunications apparatus EN : 2006 Railway applications; Electromagnetic compatibility; Part 5: Emission and immunity of fixed power supply installations and apparatus EN 50155: 2007 Railway applications; Electronic equipment used on rolling stock EN 50155: 2007 Bahnanwendung; Elektronische Einrichtungen auf Bahnfahrzeugen EN : 2011 / IEC : 2011 EN : 2006/A1: 2009 / IEC : A1: 2008 Subclause 20.6 EN : 2008 / IEC : 2007 Electroacoustics; Hearing aids; Part 13: Electromagnetic compatibility (EMC) Safety of machinery; Electrical equipment of machines; Part 1: General requirements; electromagnetic compatibility tests Electrical relays; Part 22-1: Electrical disturbance tests for measuring relays and protection equipment; 1 MHz burst immunity tests Gültigkeitsdauer: bis Ausstellungsdatum: Seite 17 von 116

18 EN : 2008 / IEC : 2008 EN : 2008 / IEC : 2007 EN : 2008 / IEC : 2008 EN : 2011 / IEC : 2008 EN : 2001 / IEC : 2001 EN : 2003 / IEC : 2003 EN : 2000 / IEC : 2000 EN : 2009 / IEC : 2008 IEC : 1993 Electrical relays; Part 22: Electrical disturbance tests for measuring relays and protection equipment; Section 2: Electrostatic discharge tests Electrical relays; Part 22-3: Electrical disturbance tests for measuring relays and protection equipment; Radiated electromagnetic field disturbance tests Electrical relays; Part 22-4: Electrical disturbance tests for measuring relays and protection equipment; Electrical fast transient/burst immunity test Electrical relays; Part 22-5: Electrical disturbance tests for measuring relays and protection equipment; Surge immunity test Electrical relays; Part 22-6: Electrical disturbance tests for measuring relays and protection equipment; Immunity to conducted disturbances induced by radio frequency fields Electrical relays; Part 22-7: Electrical disturbance tests for measuring relays and protection equipment; Power frequency immunity tests Electrical relays; Part 25: Electromagnetic emission tests for measuring relays and protection equipment Measuring Relays and protection Equipment; Part 26: Electromagnetic compatibility requirements for Measuring Relays and Protection Equipment Stabilized power supplies, d.c. output; Part 5: Measurement of the magnetic component of the reactive near field Gültigkeitsdauer: bis Ausstellungsdatum: Seite 18 von 116

19 IEC : EN : 2007 / IEC : 2007 modified Electromechanical components for electronic equipment - Basic testing procedures and measuring methods; Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories Medical electrical equipment; Part 1-2: General requirements for safety; Collateral standard: Electromagnetic compatibility; Requirements and tests EN : Medical electrical equipment; Part 2-10: A1: 2001 / Particular requirements for the safety of nerve IEC : and muscle stimulators A1: Corr 1: 2002 EN 60694: 2006 / IEC 60694: 2005 EN V1.2.1 ( ) DIN VDE 0873 Beiblatt 2 CISPR 18-2: DIN VDE 0873 Beiblatt 2 CISPR 18-2: DIN VDE 0873 Teil 1: DIN VDE 0873 Teil 1: Common specifications for high-voltage switchgear and controlgear standards spectrum Matters (ERM) Radiated emission testing of physically large telecommunication systems Radio interference characteristics of overhead power lines and high-voltage equipment; part 2: methods of measurement and procedure for determining limits; identical with CISPR 18-2: 1986 Die spezifischen Eigenschaften der von Hochspannungsfreileitungen und -anlagen verursachten Funkstörungen; Teil 2: Messverfahren und Methoden zur Bestimmung von Grenzwerten; Identisch mit CISPR 18-2: 1986 Measures against radio interference from electric utility plants and electric traction systems; radio interference from systems of 10 kv and above (VDE Guide) Maßnahmen gegen Funkstörungen durch Anlagen der Elektrizitätsversorgung und elektrischer Bahnen; Funkstörungen durch Anlagen ab 10 kv Nennspannung (VDE Richtlinie) Gültigkeitsdauer: bis Ausstellungsdatum: Seite 19 von 116

20 DIN VDE 0873 Teil 2: DIN VDE 0873 Teil 2: Radio interference characteristics of overhead power lines and high-voltage equipment; part 2: methods of measurement and procedure for determining limits; identical with CISPR 18-2: 1986 Die spezifischen Eigenschaften der von Hochspannungsfreileitungen und -anlagen verursachten Funkstörungen; Teil 2: Messverfahren und Methoden zur Bestimmung von Grenzwerten; Identisch mit CISPR 18-2: 1986 DIN VDE ; VDE : : DIN VDE ; VDE : : Radio interference suppression of telecommunication equipment; equipment in telecommunication operating rooms Funk-Entstörung von Anlagen und Geräten der Fernmeldetechnik; Anlagen und Geräte in Fernmeldebetriebsräumen EN : 2007 Aerospace series - Elements of electrical and optical connection; Test methods; Part 225: RF high potential withstanding voltage DIN EN : 2009 Luft- und Raumfahrt - Elektrische und optische Verbindungselemente; Prüfverfahren; Teil 225: HF-Hochspannungsfestigkeit DIN : 1992 DIN : 1992 DIN : 1989 DIN : 1989 Electromagnetic compatibility (EMC) in road vehicles; interferences conducted along supply lines in 12-V- and 24-V-onboard systems Elektromagnetische Verträglichkeit () in Straßenfahrzeugen; Leitungsgeführte impulsförmige Störgrößen auf Versorgungsleitungen in 12 V- und 24 V- Bordnetzen Electromagnetic compatibility (EMC) in motor vehicles; disturbances conducted along supply lines in 24 V onboard system Elektromagnetische Verträglichkeit () in Straßenfahrzeugen; Leitungsgeführte Störgrößen auf Versorgungsleitungen in 24 V-Bordnetzen Gültigkeitsdauer: bis Ausstellungsdatum: Seite 20 von 116

21 DIN : 1991 DIN : 1991 DIN : 1992 DIN : 1992 EN 55025: 2008 / IEC 55025: 2008 Electromagnetic compatibility (EMC) in motor vehicles; electrical transient transmission by capacitive and inductive coupling via lines other than the supply lines Elektromagnetische Verträglichkeit () in Straßenfahrzeugen; Eingekoppelte Störgrößen auf Geber- und Signalleitungen im 12 V- und 24 V-Bordnetz Electromagnetic Compatibility (EMC) in road vehicles; radiated disturbances Elektromagnetische Verträglichkeit () in Straßenfahrzeugen; Eingestrahlte Störgrößen Radio disturbance characteristics for the protection of receivers used on board vehicles, boats, and on devices; Limits and methods of measurement ISO : 2002 Road vehicles; Electrical disturbance by conduction and coupling; Part 1: Passenger cars and light commercial vehicles with nominal 12 V supply voltage; Electrical transient conduction along supply lines only ISO : 2011 Road vehicles; Electrical disturbance by conduction and coupling; Part 2: Commercial vehicles with nominal 24 V supply voltage; Electrical transient conduction along supply lines only ISO : 2007 Road vehicles; Electrical disturbance by conduction and coupling; Part 3: Vehicles with nominal 12 V or 24 V supply voltage; Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines ISO 10605: 2008 Road vehicles; Test methods for electrical disturbances from electrostatic discharge Gültigkeitsdauer: bis Ausstellungsdatum: Seite 21 von 116

22 ISO : 2005 ISO : 2005 ISO : 2007 ISO : 2013 ISO : 2004 ISO : 2001 ISO : 2011 ISO : 2002 Road vehicles; Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy; Part 1: General and definitions Road vehicles; Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy; Part 2: Off-vehicle radiation sources Road vehicles; Electrical disturbances by narrowband radiated electromagnetic energy; Vehicle test methods; Part 3: On-board transmitter simulation Road vehicles; Electrical disturbances by narrowband radiated electromagnetic energy; Vehicle test methods; Part 4: Bulk current injection (BCI) Road vehicles; Electrical disturbances by narrowband radiated electromagnetic energy; Component test methods; Part 2: Absorber-lined chamber Road vehicles; Component test methods for electrical disturbances from narrowband radiated electromagnetic energy; Part 3: Transverse electromagnetic mode (TEM) cell Road vehicles; Component test methods for electrical disturbances from narrowband radiated electromagnetic energy; Part 4: Bulk current injection (BCI) Road vehicles; Component test methods for electrical disturbances from narrowband radiated electromagnetic energy; Part 5: Stripline ISO : 1997/Cor 1: 1999 Road vehicles; Electrical disturbances by narrowband radiated electromagnetic energy; Component test methods; Part 6: Parallel plate antenna Gültigkeitsdauer: bis Ausstellungsdatum: Seite 22 von 116

23 ISO : 2003 Road vehicles; Component test methods for electrical disturbances from narrowband radiated electromagnetic energy; Part 7: Direct radio frequency (RF) power injection SAE J1113/1: 2012 SAE J1113/2: SAE J1113/3: SAE J1113/4: SAE J1113/11: SAE J1113/12: SAE J1113/13: SAE J1113/21: SAE J1113/22: SAE J1113/23: Electromagnetic Compatibility Measurement Procedures and limits for Components of Vehicles, Boats (up to 15 m), and Machines (Except Aircraft) (50 Hz to 18 GHz) Electromagnetic Compatibility; Measurement Procedures and Limits for Vehicle Components (Except Aircraft); Conducted Immunity; 30 Hz to 250 khz; All Leads Conducted Immunity, 250 khz to 400 MHz, Direct Injection of Radio Frequency (RF) Power Immunity to Radiated Electromagnetic Fields; Bulk Current Injection (BCI) Method Immunity to Conducted Transients on Power Leads Electrical Interference by Conduction and Coupling; Coupling Clamp and Chattering Relay Electromagnetic Compatibility Measurement Procedure for Vehicle Components; Part 13: Immunity to Electrostatic Discharge Electromagnetic Compatibility Measurement Procedure for Vehicle Components; Part 21: Immunity to Electromagnetic Fields, 10 khz to 18 GHz, Absorber-Lined Chamber Electromagnetic Compatibility Measurement Procedure for Vehicle Components; Part 22: Immunity to Radiated Magnetic Fields from Power Lines Electromagnetic Compatibility Measurement Procedure for Vehicle Components; Immunity to Radiated Electromagnetic Fields, 10 khz to 200 MHz, Strip Line Method Gültigkeitsdauer: bis Ausstellungsdatum: Seite 23 von 116

24 SAE J1113/24: SAE J1113/25: SAE J1113/26: SAE J1113/27: SAE J1113/41: SAE J1113/42: Immunity to Radiated Electromagnetic Fields; 10 khz to 200 MHz; Crawford Tem Cell and 10 khz to 5 GHz; Wideband Tem Cell Electromagnetic Compatibility Measurement Procedure for Vehicle Components; Immunity to Radiated Electromagnetic Fields, 10 khz to 500 MHz; Tri-Plate Line Method Electromagnetic Compatibility Measurement Procedure for Vehicle Components; Immunity to AC Power Line Electric Fields Electromagnetic Compatibility Measurements Procedure for Vehicle Components; Part 27: Immunity to Radiated Electromagnetic Fields Limits and Methods of Measurement of Radio Disturbance Characteristics of Components and Modules for the Protection of Receivers Used On-Board Vehicles Electromagnetic Compatibility; Component Test Procedure; Part 42: Conducted Transient Emissions ISO : 1996 Road Vehicles; Airbag components; Part 2: Testing of airbag modules. EN 50413: 2008 Basic standard on measurement and calculation procedures for human exposure to electric, magnetic and electromagnetic fields (0 Hz GHz) EN 50413: 2008; DIN VDE : DIN VDE : DIN VDE : Grundnorm zu Mess- und Berechnungsverfahren der Exposition von Personen in elektrischen, magnetischen und elektromagnetischen Feldern (0 Hz bis 300 GHz) Hazards by electromagnetic fields; protection of persons in the frequency range from 10 khz to 3000 GHz Sicherheit in elektromagnetischen Feldern; Schutz von Personen im Frequenzbereich von 10 khz bis 3000 GHz Gültigkeitsdauer: bis Ausstellungsdatum: Seite 24 von 116

25 DIN VDE : 2002 DIN VDE : 2002 DIN VDE : DIN VDE : DIN VDE : DIN VDE : Safety in electrical, magnetic and electromagnetic fields - Part 3-1: Protection of persons with active implants in the frequency range 0 Hz to 300 GHz Sicherheit in elektrischen, magnetischen und elektromagnetischen Feldern; Teil 3-1: Schutz von Personen mit aktiven Körperhilfsmitteln im Frequenzbereich 0 Hz bis 300 GHz Safety at electromagnetic fields; limits of field strengths for the protection of persons in the frequency range from 0 to 30 khz Sicherheit bei elektromagnetischen Feldern; Teil 4: Grenzwerte für Feldstärken zum Schutz von Personen im Frequenzbereich von 0 Hz bis 30 khz Safety in electric, magnetic and electromagnetic fields; Part 5: Protection against explosion Sicherheit in elektrischen, magnetischen und elektromagnetischen Feldern; Teil 5: Explosionsschutz EN 50357: 2001 Evaluation of human exposure to electromagnetic fields from devices used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications EN 50360: 2001/A1: 2012 Product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300 MHz - 3 GHz) EN 50364: 2010 Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications Gültigkeitsdauer: bis Ausstellungsdatum: Seite 25 von 116

26 EN 50366: A1: 2006 Household and similar electrical appliances - Electromagnetic fields - Methods for evaluation and measurement EN 50383: 2010 Basic standard for the calculation and measurement of electromagnetic field strength and SAR related to human exposure from radio base stations and fixed terminal stations for wireless telecommunication systems (110 MHz - 40 GHz) EN 50384: 2002 Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110 MHz - 40 GHz); Occupational EN 50385: 2002 Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110 MHz - 40 GHz); General public EN 50400: 2006 Basic standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz - 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public exposure to radio frequency electromagnetic fields, when put into service EN 50401: A1: 2011 Product standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz - 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public exposure to radio frequency electromagnetic fields, when put into service Gültigkeitsdauer: bis Ausstellungsdatum: Seite 26 von 116

27 CISPR 11: CISPR 12: CISPR 13: Industrial, scientific and medical (ISM) radiofrequency equipment; Electromagnetic disturbance characteristics; Limits and methods of measurement Vehicles, boats and internal combustion engines Radio disturbance characteristics Limits and methods of measurement for the protection of off-board receivers Sound and television broadcast receivers and associated equipment; Radio disturbance characteristics; Limits and methods of measurement CISPR 14-1: CISPR 14-2: Electromagnetic compatibility; Requirements for household appliances, electric tools and similar apparatus; Part 1: Emission Electromagnetic compatibility; Requirements for household appliances, electric tools and similar apparatus; Part 2: Immunity; Product family standard CISPR 15: CISPR : 2010 CISPR : 2010 CISPR : 2010 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment Specification for radio disturbance and immunity measuring apparatus and methods; Part 2-1: Methods of measurement of disturbances and immunity; Conducted disturbance measurements Specification for radio disturbance and immunity measuring apparatus and methods; Part 2-2: Methods of measurement of disturbances and immunity; Measurement of disturbance power Specification for radio disturbance and immunity measuring apparatus and methods; Part 2-3: Methods of measurement of disturbances and immunity; Radiated disturbance measurements Gültigkeitsdauer: bis Ausstellungsdatum: Seite 27 von 116

28 CISPR : 2003 Specification for radio disturbance and immunity measuring apparatus and methods; Part 2-4: Methods of measurement of disturbances and immunity; Immunity measurements CISPR 17: 2011 Methods of measurement of the suppression characteristics of passive radio interference filters and suppression components CISPR 18-2: 2010 Radio interference characteristics of overhead power lines and high-voltage equipment; Part 2: Methods of measurement and procedure for determining limits CISPR 19: 1983 Guidance on the use of the substitution method for measurements of radiation from microwave ovens for frequencies above 1 GHz CISPR 20: CISPR 21: CISPR 22: CISPR 23: CISPR 24: CISPR 25: CISPR/TR 30: Sound and television broadcast receivers and associated equipment; Immunity characteristics; Limits and methods of measurement Interference to mobile radiocommunications in the presence of impulsive noise; Methods of judging degradation and measures to improve performance Information technology equipment; Radio disturbance characteristics; Limits and methods of measurement Determination of limits for industrial, scientific and medical equipment Information technology equipment; Immunity characteristics; Limits and methods of measurement Limits and methods of measurement of radio disturbance characteristics for the protection of receivers used on board vehicles Test method on electromagnetic emissions from electronic ballasts for single- and double-capped fluorescent lamps Gültigkeitsdauer: bis Ausstellungsdatum: Seite 28 von 116

29 AS/NZS 2344: 1997 / Amdt 1: 2007 Limits of electromagnetic interference from overhead a.c. powerlines and high voltage equipment installations in the frequency range; 0.15 to 1000 MHz AS : 1990 Automatic fire detection and alarm systems; Methods of test for actuating devices; Electromagnetic interference test AS/NZS : 2005 AS/NZS 4052: 1992 AS/NZS 4053: 1997 Approval and test specification; Medical electrical equipment; General requirements for safety; Collateral Standard: Electromagnetic compatibility; Requirements and tests Guidance on the use of the substitution method for measurements of radiation from microwave ovens for frequencies above 1 GHz; equivalent CISPR 19 Limits and methods of measurement of immunity characteristics of sound and television broadcast receivers and associated equipment; equivalent CISPR 20, EN AS/NZS : 2013 AS/NZS : 2012 AS/NZS : 2013 Electromagnetic compatibility (EMC); Limits; Limits for harmonic current emissions (equipment input current less than or equal to 16 A per phase); equivalent EN Electromagnetic compatibility (EMC); Limits; Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current less than or equal to 16 A; equivalent EN Electromagnetic compatibility (EMC); Limits; Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16 A Gültigkeitsdauer: bis Ausstellungsdatum: Seite 29 von 116

30 AS/NZS : 2012 ICES-001: Issue 4, June 2006 ICES-002: Issue 6, March 2013 ICES-003: Issue 5, August 2012 ICES-004: Issue 4, June 2013 ICES-005: Issue 3, May 2009 ICES-006: Issue 2, June 2009 IEEE Std 299: 2006 CAN/CSA-C : 2006 C108.8-M1983: 2000 ANSI/IEEE C63.4: 2003 Electromagnetic compatibility (EMC); Testing and measurement techniques; General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto; equivalent EN Industrial, Scientific and Medical Radio Frequency Generators Vehicles, Boats and Other Devices Propelled by an Internal Combustion Engine, Electrical Means or Both Digital Apparatus Alternating Current High Voltage Power Systems Radio Frequency Lighting Devices AC Wire Carrier Current Devices (Unintentional Radiators) Method for Measuring the Effectiveness of Electromagnetic Shielding Enclosures Vehicles, Boats, and Internal Combustion Engine Driven Devices; Radio Disturbance Characteristics; Limits and Methods of Measurement for the Protection of Receivers Except Those Installed in the Vehicle; Boat; Device Itself or in Adjacent Vehicles; Boats; Devices Electromagnetic Emissions from Data Processing Equipment and Electronic Office Machines American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 khz to 40 GHz Gültigkeitsdauer: bis Ausstellungsdatum: Seite 30 von 116