Titel Gummi-Metall-Elemente
Gummi-Metall-Puffer Gummi-Metall-Puffer, Ausführung A Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm 05000222 06 07 M3 06 05000223 08 06 M3 06 05000225 08 08 M3 06 05000230 10 10 M4 10 05000237 15 08 M4 10 05000240 15 15 M4 13 05000246 15 20 M4 13 05000250 18 8,5 M6 16 05000254 20 15 M6 15 05000261 20 20 M6 15 05000268 20 25 M6 15 05000275 25 10 M6 18 05000278 25 15 M6 18 05000286 25 20 M6 18 05000294 25 30 M6 18 05000298 30 15 M8 20 05000304 30 20 M8 20 05000314 30 30 M8 20 05000328 40 30 M8 23 05000333 40 40 M8 23 05000342 50 20 M10 28 05000350 50 30 M10 28 05000359 50 40 M10 28 05000363 50 45 M10 28 05000367 50 50 M10 28 05000374 70 45 M10 30 05000379 75 25 M12 37 05000384 75 40 M12 37 05000389 75 50 M12 37 05000392 75 55 M12 37 05000399 100 40 M16 45 05000407 100 55 M16 45 05000412 100 60 M16 45 2
Gummi-Metall-Puffer Gummi-Metall-Puffer, Ausführung B Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge s = Gewindetiefe Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm s / mm 05000224 08 06 M3 06 3 05000226 08 08 M3 06 3 05000231 10 10 M4 10 4 05000241 15 15 M4 13 4 05000247 15 20 M4 13 4 05000255 20 15 M6 15 6 05000262 20 20 M6 15 6 05000269 20 25 M6 15 6 05000279 25 15 M6 18 6 05000288 25 20 M6 18 6 05000295 25 30 M6 18 6 05000299 30 15 M8 20 8 05000305 30 20 M8 20 8 05000315 30 30 M8 20 8 05000329 40 30 M8 23 8 05000334 40 40 M8 23 8 05000343 50 20 M10 28 10 05000352 50 30 M10 28 10 05000360 50 40 M10 28 10 05000364 50 45 M10 28 10 05000368 50 50 M10 28 10 05000375 70 45 M10 30 10 05000380 75 25 M12 37 12 05000385 75 40 M12 37 12 05000390 75 50 M12 37 12 05000393 75 55 M12 37 12 05000400 100 40 M16 45 16 05000408 100 55 M16 45 16 05000414 100 60 M16 45 16 3
Gummi-Metall-Puffer Gummi-Metall-Puffer, Ausführung C Abkürzungen: d = Durchmesser h = Höhe g = Gewinde s = Gewindetiefe Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde s / mm 05000227 08 08 M3 03 05000232 10 10 M4 04 05000236 13 26 M4 04 05000242 15 15 M4 04 05000248 15 20 M4 04 05000263 20 20 M6 06 05000270 20 25 M6 06 05000289 25 20 M6 06 05000296 25 30 M6 06 05000306 30 20 M8 08 05000316 30 30 M8 08 05000330 40 30 M8 08 05000335 40 40 M8 08 05000353 50 30 M10 10 05000361 50 40 M10 10 05000365 50 45 M10 10 05000369 50 50 M10 10 05000376 70 45 M10 10 05000386 75 40 M12 12 05000391 75 50 M12 12 05000394 75 55 M12 12 05000401 100 40 M16 16 05000409 100 55 M16 16 05000415 100 60 M16 16 05001576 150 55 M16 16 05001140 150 75 M16 16 05000434 150 75 M20 20 4
Gummi-Metall-Puffer Gummi-Metall-Taillenpuffer, Ausführung CT Abkürzungen: d = Durchmesser h = Höhe g = Gewinde t = Gewindetiefe Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindetiefe / mm 05000310 30 20 M8 08 05000312 30 25 M8 08 05000320 30 30 M8 08 05000994 40 30 M8 08 05000338 40 48 M8 08 05000355 50 30 M10 10 05000388 75 40 M12 12 05000411 100 55 M16 16 05000418 100 75 M16 16 5
Gummi-Metall-Puffer Gummi-Metall-Puffer, Ausführung D Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm 05000233 10 10 M4 10 05000238 15 13 M4 13 05000243 15 15 M4 13 05000249 18 7,5 M6 16 05000252 20 13,5 M6 15 05000256 20 15 M6 15 05000264 20 20 M6 15 05000271 20 25 M6 15 05000274 25 8 M6 18 05000276 25 13 M6 18 05000280 25 15 M6 18 05000282 25 17 M6 18 05000290 25 20 M6 18 05000292 25 28 M6 18 05000300 30 15 M8 20 05000302 30 17 M8 20 05000307 30 20 M8 20 05000317 30 30 M8 20 05000325 40 28 M8 23 05000332 40 38 M8 23 05000340 50 17 M10 28 05000344 50 21 M10 28 05000346 50 28 M10 28 05000381 75 25 M12 37 05000402 100 40 M16 45 05000404 100 50 M16 45 6
Gummi-Metall-Puffer Gummi-Metall-Puffer, Ausführung E Abkürzungen: d = Durchmesser h = Höhe g = Gewinde t = Gewindetiefe Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindetiefe / mm 05000234 10 10 M4 04 05000244 15 15 M4 04 05000253 20 13,5 M6 06 05000257 20 15 M6 06 05000265 20 20 M6 06 05000272 20 25 M6 06 05000277 25 13 M6 06 05000281 25 15 M6 06 05000283 25 17 M6 06 05000291 25 20 M6 06 05000293 25 28 M6 06 05000301 30 15 M8 08 05000303 30 17 M8 08 05000308 30 20 M8 08 05000318 30 30 M8 08 05000327 40 28 M8 08 05000339 50 17 M10 10 05000345 50 21 M10 10 05000348 50 28 M10 10 05000382 75 25 M12 12 05000403 100 40 M16 16 05000406 100 50 M16 16 7
Gummi-Metall-Puffer Gummi-Metall-Puffer, Ausführung DS Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm 05000239 15 14 M4 13 05000260 20 17 M6 18 05000266 20 23,5 M6 18 05000285 25 18,5 M6 18 05000313 30 28,5 M8 20 05000326 40 28,5 M8 23 05000347 50 28 M10 33 05000373 70 43 M10 30 05000383 75 37 M12 37 05000405 100 50 M16 45 8
Gummi-Metall-Anschlagpuffer Gummi-Metall-Anschlagpuffer, Ausführung KE Abkürzungen: d = Durchmesser h = Höhe g = Gewinde t = Gewindetiefe Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindetiefe / mm 05000356 50 35 M10 10 05000397 80 60 M12 12 05000422 125 90 M16 16 Gummi-Metall-Anschlagpuffer, Ausführung K Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm 05000284 25 17 M6 18 05000341 50 18 M10 28 05000396 80 x 80 vkt. 25 M12 35 05000556 80 x 80 vkt. 30 M12 37 05000421 125 45 M16 45 9
Gummi-Metall-Anschlagpuffer Gummi-Metall-Parabelpuffer, Ausführung KP Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm 05000267 20 24 M6 18 05000321 30 36 M8 20 05001839 50 67 M8 36 05000370 50 58 M10 28 05000395 75 89 M12 37 05000419 115 136 M16 43 05000424 165 195 M16 45 Gummi-Metall-Taillenpuffer, Ausführung AT Abkürzungen: d = Durchmesser h = Höhe g = Gewinde l = Gewindelänge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Durchmesser / mm Höhe / mm Gewinde Gewindelänge / mm 05000229 10 08 M4 10 05000245 15 15 M4 13 05000258 20 15 M6 18 05000309 30 20 M8 20 05000311 30 25 M8 20 05000319 30 30 M8 20 05002220 40 30 M8 23 05000337 40 48 M8 23 05000354 50 30 M10 33 05001871 60 60 M10 28 05000387 75 40 M12 37 05000410 100 55 M16 45 05000417 100 75 M16 45 10
Gummi-Metall-Schienen Gummi-Metall-Schienen, Ausführung 1 Abkürzungen: S = Metallstärke H = Höhe B = Breite L = Länge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Andere Abmessungen und Längenzuschnitte auf Anfrage. Artikelnummer B / mm H / mm L / mm S / mm 05000331 40 35 2000 10 05000357 50 35 2000 10 05000362 50 40 2000 10 05000366 50 45 2000 10 05001355 50 50 2000 10 05001356 50 70 2000 10 05001115 30 70 2000 10 05001424 45 70 2000 10 05000378 70 50 2000 10 05001357 70 55 2000 10 05001358 80 45 2000 10 05000398 80 80 2000 10 05000416 100 60 2000 15 05001359 100 80 2000 15 05000420 120 60 2000 15 05001360 120 80 2000 15 05001361 150 60 2000 15 05001362 150 80 2000 15 11
Gummi-Metall-Schienen Gummi-Metall-Schienen, Ausführung 2, mit verstärktem Stahl Abkürzungen: S = Metallstärke H = Höhe B = Breite S1 = Metallstärke L = Länge Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer B / mm H / mm L / mm S / mm S1 / mm 05001363 50 35 2000 10 5 05001364 50 45 2000 10 5 05001365 50 50 2000 10 5 05002326 50 55 2000 10 5 05001366 60 35 2000 11 5 05001367 70 30 2000 12 5 05001368 70 45 2000 12 5 05001369 70 55 2000 12 5 05001370 100 45 2000 15 5 05001371 100 60 2000 15 5 Gummi-Metall-Schienen mit überstehender Grundplatte Abkürzungen: B = Breite H = Höhe h = Gummihöhe S1 = Metallstärke oben S2 = Metallstärke unten L1 = Metalllänge oben L2 = Metalllänge unten Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer B / mm H / mm h / mm s1 / mm s2 / mm L1 / mm L2 / mm 05000059 50 40 20 12 8 150 200 05000060 50 40 20 12 8 220 270 05001834 100 60 30 15 15 230 470 05002027 100 60 30 15 15 230 480 05001353 100 60 30 15 15 360 480 05001849 100 30 60 15 15 430 550 12
Gummi-Metall-Schienen Gummi-Metall-Anschlagschienen Abkürzungen: b = Breite h = Höhe l1 = Überstehendes Metall l = Gesamtlänge s = Metallstärke d = Bohrungs-Durchmesser a = Lochabstand a1 = Lochabstand a2 = Lochabstand Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Artikelnummer a / mm a1 / mm a2 /mm b / mm h / mm l1 / mm l / mm s / mm d / mm 05002323 15 25 50 35 30 130 5 8,5 05001867 15 25 50 70 30 130 5 8,5 05000496 20 25 50 100 45 40 200 10 13 05002391 20 25 50 100 80 40 200 10 13 05001349 25 30 60 120 45 50 250 10 15 05002325 25 30 60 120 70 50 250 10 15 05002324 25 35 80 150 50 50 300 15 17 05001946 25 35 80 150 80 50 300 15 17 Schwingmetall -U-Schienen Abkürzungen: b = Gesamtbreite h = Gesamthöhe l = Länge s = Metallstärke Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Artikelnummer Form-Nummer b / mm h / mm l / mm s / mm 05001348 27847 110 34 25 4 05001347 27753 110 34 50 4 05000559 27788 110 34 75 4 05000497 20302 110 34 2000 4 13
Gummi-Metall-Elemente Megiflex -Scheiben Abkürzungen: A = Metalldurchmesser außen a = Metalldurchmesser innen B = Gummidurchmesser außen b = Gummidurchmesser innen H = Höhe C = Wulst-Durchmesser s = Metallstärke Material NR Gummi-Shorehärte: mittel = 60 ± 5 Shore A Anfertigungsware, auf Anfrage Artikelnummer Form-Nummer A / mm a / mm B / mm b / mm H / mm C /mm s / mm VE / Stück 05000679 741473 65 26 62 30 11 46 1 20 05000680 741481 95 45 90 50 10,5 70 1,5 10 05000676 741444 100 35 90 40 27,5 64 1,5 10 05001326 741401 110 30 102 38 20,8 76 1,75 6 05000683 741493 110 40 102 44 15,8 76 1,75 6 05000682 741488 130 55 123 60 16 90 2 6 05000678 741472 153 55 145 60 30 102 2 4 05000674 741432 164 60 156 64 23 110 2 4 05000681 741482 210 55 200 60 20 154 2-05000675 741436 210 95 200 100 20 154 2 4 05001332 741434 240 70 230 76 25 154 2 4 14
Gummi-Metall-Elemente Federscheiben Abkürzungen: A = Metalldurchmesser außen a = Metalldurchmesser innen B = Gummidurchmesser außen b = Gummidurchmesser innen H = Höhe C = Wulst-Durchmesser s = Metallstärke Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Artikelnummer A / mm a / mm B / mm b / mm H / mm C /mm s / mm VE / Stück 05003935 65 26 62 30 11 46 1 20 05003943 95 45 90 50 10,5 70 1,5 10 05003385 100 35 90 40 27,5 64 1,5 10 05003667 110 30 102 38 20,8 76 1,75 6 05003582 110 40 102 44 15,8 76 1,75 6 05003944 130 55 123 60 16 90 2 6 05003945 153 55 145 60 30 102 2 4 05003065 155 75 150 80 12 115 2-05003946 160 90 155 95 12 125 2-05003810 164 60 156 64 16 110 2-05003809 164 60 156 64 23 110 2 4 05003947 210 55 200 60 20 154 2-05003593 210 95 200 100 20 154 2 4 05003948 220 66 200 100 62 154 2-05003534 240 70 230 76 25 154 2 4 05002392 265 78 250 90 27,8 166 2,75-15
Gummi-Metall-Elemente Megi -Lager Material NR Artikelnummer Form-Nummer Härte VE / Stück 05000685 742022 45 +/- 5 Shore A 12 60 +/- 5 Shore A 12 70 +/- 5 Shore A 12 05001104 742034 S6 40 +/- 5 Shore A 4 50 +/- 5 Shore A 4 60 +/- 5 Shore A 4 05001256 742034 S7 40 +/- 5 Shore A 4 50 +/- 5 Shore A 4 60 +/- 5 Shore A 4 70 +/- 5 Shore A 4 05000686 742034 S9 70 +/- 5 Shore A 4 05000687 742157 70 +/- 5 Shore A 1 60 +/- 5 Shore A 1 16
Gummi-Metall-Elemente Gummi-Metall-Lager Material NR Artikelnummer Härte VE / Stück 05003949 45 +/- 5 Shore A 12 60 +/- 5 Shore A 12 70 +/- 5 Shore A 12 Schwingmetall -Geräteelemente Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Form 25187 Form 25284 Form 21423 Form 24332 Artikelnummer Form-Nummer Gewicht g VE / Stück 05000513 25187 35 52 05000517 25284 70 54 05000505 21423 75 30 05000508 24332 124 54 17
Gummi-Metall-Elemente Megi -Instrumentenlagerung Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Form 782000 Form 782001 Form 786001 Form 786002 Artikelnummer Form-Nummer VE / Stück 05000745 782000 12 05001312 782001 8 05000748 786001 12 05000749 786002 20 Megi -Ringpuffer Abkürzungen: D = Außendurchmesser oben A = Innendurchmesser oben B = Innendurchmesser unten C = Außendurchmesser unten E = Höhe F = Kragenhöhe Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Artikelnummer Form-Nummer D / mm A / mm B / mm C /mm E / mm F / mm VE / Stück 05000668 741027 36 8,5 12 18 10 4 50 05000670 741092 36 16,6-20 8 3 50 05000666 741020 50 16,5 20 23 13 9,5 50 05000667 741026 60 20,5 24 27 13 10,5 25 18
Gummi-Metall-Elemente Schwingmetall -Bügelelemente Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Form 31510 Form 31700 Artikelnummer Form-Nummer Gewicht g VE / Stück 05000574 31510 150 30 05000596 31700 420 20 Schwingmetall -Torsionsbuchse Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Artikelnummer Form-Nummer 05000568 27843/a 19
Gummi-Metall-Elemente Megi -Ringelemente Material NR Gummi-Shorehärte: mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Artikelnummer Form-Nummer h / mm b / mm VE / Stück 05000747 785000 26 65 10 Schwingmetall -Ringelemente Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Artikelnummer Form-Nummer h / mm b / mm VE / Stück 05000506 21489 26 65 8 20
Gummi-Metall-Elemente Megi -Deckenelemente Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A Artikelnummer Form-Nummer Gewinde VE / Stück 05000746 782002 mit Gewindebolzen M8 10 05001315 782002 S1 mit Innengewinde M8 10 Gummi-Metall-Hutelemente Material: NR Abkürzungen: a = Lochabstand l = Länge b = Breite h = Höhe Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer a / mm b / mm l / mm h / mm G 05002295 45 35 60 20 M6 05002296 70 50 90 32 M10 05002297 105 80 140 50 M16 21
Gummi-Metall-Elemente Schwingmetall -Dachelemente Material NR Gummi-Shorehärte: mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Lagerware alle Shorehärten Artikelnummer Form-Nummer 05000598 38451 05001313 33660 22
Gummi-Metall-Elemente Schwingmetall -Glockenelemente Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Form 58500 Form 27994 Artikelnummer Form-Nummer Gewicht g VE / Stück 05001314 58500 100 40 05000572 27994 110 60 23
Gummi-Metall-Elemente Schwingmetall -Hydrolager Material NR Gummi-Shorehärten und Konsolen auf Anfrage V 250 V 600 V 1500 V 3200 Artikelnummer Form-Nummer Ausführung d1 / mm d2 / mm h / mm h1 / mm s / mm 05001316 102216 V 250 46 38 62,5 26,5 2,0 05000623 100787 V 600 64 45 91,0 32,0 2,5 05001317 54439 V 1500 64 60 103,0 44,0 2,5 05002330 210182 V 3200 107 80 120,0 54,0 8,0 Klemmdübel Material: Temperatur: NBR -30 C bis +80 C Andere Gummiqualitäten und Shorehärten auf Anfrage Artikelnummer b / mm D / mm D1 / mm d / mm G L / mm l / mm 05001555 2,5 9 2,5 3,3 M3 9 8 05002043 3,0 12 3,0 9,3 M4 14,5 10,5 05002073 3,5 15 3,5 5,4 M5 14,5 13 05001556 1,5 16 1,5 8 M6 16,5 10 05001557 5,0 24 5,0 10 M8 22 19,5 24
Gummi-Metall-Elemente Schwingmetall -Flansch-Elemente Gummi-Shorehärte FNKN 45 (Werkstoff NR), ± 5 Shore A Material NR Abkürzungen A = Durchmesser Gummi B = Gesamthöhe G = Gesamtlänge D = Gummistärke am Kopf M = Lochdurchmesser Kunststoff-Flansch Artikelnummer Form-Nummer A / mm B / mm D / mm G / mm M / mm 05001320 48684 33 29 8 58 6.3 05000604 48685 47 40 12 90 9 05000605 48686 68 54 16 117 9 05001319 48687 68 49 16 117 9 05000606 48688 68 44 16 117 9 05000607 48689 82 68 20 150 13 05000608 48690 82 62 20 150 13 05001321 48691 82 51 20 150 13 05000609 48692 96 82 20 174 13 05001322 48693 96 76 20 174 13 05000610 48694 96 68 20 174 13 25
Kabinenlagerung Gummi-Metall-Konen Material: NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Flansch Lochabstand / mm Loch-Ø / mm 05001981 2-fach Loch 64 6.5 05001948 2-fach Loch 80 11 05001968 4-fach Loch 80 / 65 11 05001917 4-fach Loch 90 / 74 11 05001761 4-fach Loch 112 / 92 11 26
Gummi-Metall-Lager Gummi-Maschinen-Lager Material: NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Gewinde Höhe / mm Breite / mm 05001884 M10 40 55 27
Torsionsbuchsen HL-Buchsen Abkürzungen: A = Außendurchmesser i = Innendurchmesser Li = Länge Innenbuchse LA = Länge Außenbuchse Material NR Gummi-Shorehärte: mittel = 50 ± 5 Shore A Artikelnummer A / mm l / mm Li / mm La / mm VE / Stück 05002478 24 10 17 14 20 05003960 45 20 62,5 59,5 20 05003962 45 20 62,5 55,0 20 05003964 55 25 93,5 89,5 10 05003965 26 12 24 17,5 30 05003966 75 40 70 57 10 05003967 70 50 60 60 10 05003968 50 25 67,5 65,5 20 05003396 34 18 36 32 20 05003969 55 30 94 89,5 20 05003956 40 26 45 40 20 05003970 80 50 100 95 10 05003971 26 12 36 32 50 28
Maschinenlagerungen Maschinenfüße mit rechteckigem Flansch Abkürzungen: b = Breite G = Gewinde h = Höhe Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Artikelnummer Ausführung b / mm h / mm G Lochabstand / mm Bemerkung 05001575 MP184A 184 63 M20 150 Abreißsicherung 05001938 MP184010 184 63 M20 150 Standard 05001939 MP184110 184 63 M20 150 Höhenverstellung 05001996 MP168A 168 52 M16 132 Abreißsicherung 05001878 MP168011 168 52 M16 132 Standard 05002897 MP168111 168 52 M20 132 Höhenverstellung 29
Maschinenlagerungen Maschinenfüße mit ovalem Flansch Abkürzungen: b = Breite G = Gewinde h = Höhe Material NR Gummi-Shorehärte: weich = 43 ± 5 Shore A mittel = 57 ± 5 Shore A hart = 68 ± 5 Shore A Artikelnummer Ausführung b / mm h / mm G Lochabstand / mm Bemerkung 05002112 MP128 128 30 M10 110 Standard 05002111 MP128A 128 30 M10 105 Abreißsicherung 05001740 MP170A 170 39 M12 140 Abreißsicherung 05001913 MP170013 170 39 M12 140 Standard 05001737 MP216A 216 52 M16 184 Abreißsicherung 30
Maschinenlagerungen Megi -Maschinenfüße mit rechteckigem Flansch Abkürzungen: b = Breite G = Gewinde h = Höhe Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Artikelnummer Form-Nummer b / mm h / mm G Bemerkung VE in Stk. 05000750 786010 184 63 M20 Standard 4 05000761 786110 184 63 M20 Höhenverstellung 4 05000764 786210 184 63 M20 Abreißsicherung 4 05000751 786011 168 51,5 M16 Standard 4 05000765 786211 168 51,5 M16 Abreißsicherung 4 Typ 184 horizontale Belastung Typ 184 vertikale Belastung Typ 168 horizontale Belastung Typ 168 vertikale Belastung 31
Maschinenlagerungen Megi -Maschinenfüße mit ovalem Flansch Abkürzungen: b = Breite G = Gewinde h = Höhe Material NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 60 ± 5 Shore A hart = 70 ± 5 Shore A Artikelnummer Form-Nummer b / mm h / mm G Bemerkung VE in Stk. 05000753 786013 170 39 M12 Standard 8 05000763 786113 170 39 M16 Höhenverstellung 8 05000766 786213 170 39 M12 Abreißsicherung 8 05000754 786014 128 30 M10 Standard 8 05000767 786214 128 30 M10 Abreißsicherung 8 Typ 170 horizontale Belastung Typ 170 vertikale Belastung Typ 128 horizontale Belastung Typ 128 vertikale Belastung 32
Maschinenlagerungen Maschinenfüße, Stahl verzinkt Abkürzungen: D = Durchmesser H = Höhe G = Gewinde L = Gewindelänge Ni = Nivellierhöhe Material: NBR, 70 +/-5 Shore A Lieferung komplett mit Schraube, Mutter und Scheibe Artikelnummer Ausführung D / mm H / mm G L / mm zul. statische Höchtlast pro Element 05001715 NM 80 80 27 M10 80 400 kg 05002196 NM 80 80 27 M12 80 400 kg 05001643 NM 100 100 37 M12 100 700 kg 05000003 NM 120 120 37 M12 120 1000 kg 05000004 NM 160 160 37 M16 120 4000 kg 05001753 NM 185 185 45 M20 140 6000 kg Maschinenfüße, Edelstahl V2A Material: NBR, 70+/-5 Shore A Lieferung komplett mit Schraube, Mutter und Scheibe Abkürzungen: D = Durchmesser H = Höhe G = Gewinde L = Gewindelänge Ni = Nivellierhöhe Artikelnummer Ausführung D / mm H / mm G L / mm zul. statische Höchtlast pro Element 05001911 NM 80 V 80 27 M12 80 400 kg 05001212 NM 120 V 120 37 M12 120 1000 kg 05000005 NM 160 V 160 37 M16 120 4000 kg 05002861 NM 185 V 185 45 M20 140 6000 kg Bodenplatte auf Anfrage Bodenplatten werden benötigt, wenn an der lagernden Maschine oder Anlage starke Schubkräfte in horizontaler Richtung auftreten, um ein seitliches Verrutschen zu verhindern. 33
Maschinenlagerungen Schwingmetall -Topfelemente Abkürzungen: a = Lochabstand b = Gesamtbreite d = Lochdurchmesser h = Gesamthöhe g = Gewindegröße s = Metallstärke Material: NR Gummi-Shorehärte: weich = 45 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Artikelnummer Form-Nummer a / mm b / mm d / mm h / mm g s / mm 05000620 58540 88 108 9 40 M12 3 05000597 33629 132 168 13 50 M16 4 05000622 58541 165 200 13 70 M20 6 Nivellierspindel & Scheibe Artikelnummer für Form g1 l / mm SW S1 / mm 05000621 58540 M12 85 8 5 05001307 33629 M16 96 10 6 05001308 58541 M20 106 14 6 Unterlegmatte Artikelnummer für Form a / mm b / mm s2 / mm 05001309 58540 88 108 2,5 05000792 33629 132 168 3,0 05001310 58541 165 200 4,0 34
Maschinenlagerungen Schwingmetall -Topfelemente Abkürzungen: b = Gesamtbreite d = Durchmesser h = Gesamthöhe Material NR Gummi-Shorehärte: weich = 40 ± 5 Shore A mittel = 55 ± 5 Shore A hart = 65 ± 5 Shore A Form 103965 Form 104169 Artikelnummer Form-Nummer b / mm d / mm h / mm 05000624 103965 122 72 33 05000625 104169 55 55 40 35
Maschinenlagerungen Maschinenunterlage EMU Maschinenunterlage, Elastomerkörper aus NBR-Qualität mit hoher Elastizität, öl-und alterungsbeständig, Metallplatte aus S235JR, Metalloberfläche lackiert in RAL 5010 Enzianblau, Metallplatte mit Schraubenaufnahme/Zentrierung, Sondergrößen, Gummiqualitäten und Lackierungen auf Anfrage Material: NBR Abkürzungen: b = Breite l = Länge h = Gesamthöhe s = Stahlstärke d = Bohrungsdurchmesser t = Bohrungstiefe Toleranzen nach DIN ISO 3302-1/2 M3 C Artikelnummer Form-Nummer b mm l mm h mm s mm d mm t mm Belastungsbereich 05004053 EMU60 60 60 25 10 14 4 100-400 kg 05004054 EMU60 60 60 25 10 14 4 100-400 kg 05004055 EMU60 60 60 25 10 14 4 100-400 kg 05004056 EMU60 60 60 25 10 14 4 100-400 kg 05004057 EMU60 60 60 25 10 14 4 100-400 kg 05004051 EMU60 60 60 25 10 14 4 100-400 kg 05004058 EMU60 60 60 25 10 14 4 100-400 kg 36
Elastische Lagerungselemente Maschinenlager Material NR Anfertigungsware Artikelnummer Ausführung Shore-Härte +/-5 Shore A A B C P F x M CF L S max. Belastung kg 05001637_45 45 80 38 60 M12 14 x 11 100 120 3 36,0 05001637_50 50 80 38 60 M12 14 x 11 100 120 3 52,0 05001637_60 60 80 38 60 M12 14 x 11 100 120 3 64,0 05001637_70 70 80 38 60 M12 14 x 11 100 120 3 96,0 05001970_45 1045016W 45 104 49 75 M16 30 x 13 oder 20 x 13 140 183 4 120,0 05001970_60 1045016M 60 104 49 75 M16 30 x 13 oder 20 x 13 140 183 4 190,0 05001970_70 1045016H 70 104 49 75 M16 30 x 13 oder 20 x 13 140 183 4 300,0 05001970_80 1045016XH 80 104 49 75 M16 30 x 13 oder 20 x 13 140 183 4 475,0 05003585_45 1307020W 45 132 71 112 M20 34 x 18 oder 26 x 18 182 230 5 333,0 05003585_60 1307020M 60 132 71 112 M20 34 x 18 oder 26 x 18 182 230 5 540,0 05003585_70 1307020H 70 132 71 112 M20 34 x 18 oder 26 x 18 182 230 5 810,0 05003585_80 1307020XH 80 132 71 112 M20 34 x 18 oder 26 x 18 182 230 5 880,0 37
Elastische Lagerungselemente Elastische Lagerungselemente - Isolatoren Material NR Anfertigungsware Wahlweise kann der Artikel 05001755 mit Innengewinde M10 geliefert werden. Artikelnummer Shore-Härte +/-5 Shore A B L1 L2 G F x M CF S Federrate kg / mm max. Belastung max. stat. Entfederung kg mm 05001851_45 45 20 64 43 M6 7 50 2 1,5 4,5 3,0 05001851_60 60 20 64 43 M6 7 50 2 3,0 9,0 3,0 05001851_70 70 20 64 43 M6 7 50 2 9,0 16,5 3,0 05001755_45 45 25 88 59 M8 08 x 12 65 / 73 2,5 4,0 26,5 7,5 05001755_60 60 25 88 59 M8 08 x 12 65 / 73 2,5 6,0 43,0 7,5 05001755_70 70 25 88 59 M8 08 x 12 65 / 73 2,5 10,0 75,0 7,5 38
Antriebselemente Reibringe mit Stahldrahtarmierung RM: RS: Naturkautschuk-Basis Härte 73 Shore A zulässige Umgebungstemperatur -30 bis +70 C ab 30 C mit reduzierter Anpresskraft Polychloroprenkautschuk-Basis Härte 83 Shore A zulässige Umgebungstemperatur -30 bis +90 C ab 50 C mit reduzierter Anpresskraft Z: für zylindrische Radkörper K: für konische Radkörper (auf Anfrage) Artikelnummer Form-Nummer Außen-Ø / mm Breite / mm Innen-Ø / mm Ausführung 05000466 95/50-50 Z 95 50 50 RS 05001926 125/50-75 Z 125 50 75 RS 05000054 150/50-100 Z 150 50 100 RS 05000468 160/50-100 Z 160 50 100 RS 05001644 250/60-170 K 250 60 170 RS 05000469 200/50-140 K 200 50 140 RS 05000470 200/75-100 Z 200 75 100 RS 05001638 230/50-170 Z 230 50 170 RS 05000472 230/75-120 Z 230 75 120 RS 05000473 250/60-170 Z 250 60 170 RM 05000474 200/50-140 Z 200 50 140 RS 05000475 250/75-140 Z 250 75 140 RM 05001696 250/75-140 Z 250 75 140 RS 05001373 280/60-190 Z 280 60 190 RS 05001733 310/60-220 Z 310 60 220 RM 05001864 310/60-220 Z 310 60 22 RS 05002054 360/75-270 Z 360 60 270 RM 05000477 400/60-305 Z 400 60 305 RM Weitere Größen auf Anfrage 39
Antriebselemente Führungsrollen mit Stahldrahtarmierung / Stahlring Konische Fußausrüstung FM Naturkautschuk-Basis Härte 67 Shore A, geeignet für Geschwindigkeiten bis 14 m/s (50 km/h) FMH Naturkautschuk-Basis geeignet für Geschwindigkeiten bis 20 m/s (72 km/h) Artikelnummer Form-Nummer Außen-Ø / mm Breite / mm Innen-Ø / mm Laufflächen Qualität 05000476 300/75-220 K 300 75 220 FM Weitere Größen auf Anfrage Reibräder B als Antriebselement, auf Stahlkern aufvulkanisiert b Material: CR Abkürzungen: D = Gummi Außen b = Gummi Breite d = Metall Außen B = Metall Breite DIN 332 Artikelnummer Form-Nummer Gummi Außen Gummi Breite Metall Außen Metall Breite 05000590 RR40 40 10 25 13 05000591 RR45 45 11 28 14 05002093 RR50 50 12 32 16 05000592 RR56 56 14 35 18 05000576 RR63 63 16 40 20 05000593 RR71 71 18 45 22 05000577 RR80 80 20 50 25 05000594 RR90 90 22 55 27 05000578 RR100 100 25 65 30 05000579 RR112 112 28 70 33 05000580 RR125 125 32 80 37 05000581 RR140 140 36 90 41 05000595 RR160 160 40 100 45 40
Anschlagpuffer aus zelligem PU Kran-Zell-Puffer Anschlagpuffer aus Diepocell Besonders geeignet für den Einsatz: im Kranbau im allgemeinen Maschinenbau in der Fördertechnik Ausführung Puffergröße 1 Lfd. Nr. Maße (mm) Ø D x H M x L (mm) Außengewinde Innengewinde Artikel-Nr. M Artikel-Nr. Gewicht (kg) 0 2 70 x 70 M 12 x 35 233 701 045 M 12 235 701 045 0,25 1 1 80 x 40 M 12 x 35 05002052 M 12 235 801 045 0,21 2 2 80 x 80 M 12 x 35 05002358 M 12 235 802 045 0,31 3 3 80 x 120 M 12 x 35 05002133 M 12 235 803 045 0,42 4 1 100 x 50 M 12 x 35 233 101 045 M 12 235 101 045 0,31 5 2 100 x 100 M 12 x 35 233 102 045 M 12 235 102 045 0,52 6 3 100 x 150 M 12 x 35 05001627 M 12 235 103 045 0,73 7 1 125 x 63 M 12 x 35 233 121 045 M 12 235 121 045 0,51 8 2 125 x 125 M 12 x 35 233 122 045 M 12 235 122 045 0,92 9 3 125 x 190 M 12 x 35 05001771 M 12 235 123 045 1,32 10 1 160 x 80 M 12 x 35 05001772 M 12 235 161 045 0,95 11 2 160 x 160 M 12 x 35 233 162 045 M 12 235 162 045 1,80 12 3 160 x 240 M 12 x 35 05001640 M 12 235 163 045 2,66 13 1 200 x 100 M 12 x 35 233 201 045 M 12 235 201 045 1,76 14 2 200 x 200 M 12 x 35 233 202 045 M 12 235 202 045 3,43 15 3 200 x 300 M 12 x 35 05001659 M 12 235 203 045 5,10 16 1 250 x 125 M 24 x 80 233 251 045 M 24 235 251 045 5,40 17 2 250 x 250 M 24 x 80 05002451 M 24 235 252 045 8,50 18 3 250 x 375 M 24 x 80 233 253 045 M 24 235 253 045 11,50 19 1 315 x 158 M 24 x 80 233 311 045 M 24 235 311 045 8,50 20 2 315 x 315 M 24 x 80 233 312 045 M 24 235 312 045 14,65 21 3 315 x 475 M 24 x 80 233 313 045 M 24 235 313 045 20,80 22 1 400 x 200 M 30 x 80 233 401 045 M 30 235 401 045 16,50 23 2 400 x 400 M 30 x 80 233 402 045 M 30 235 402 045 29,10 24 3 400 x 600 M 30 x 80 233 403 045 M 30 235 403 045 41,60 Ausführung Puffergröße 2 (Bis Ø 200 mm) Ausführung Puffergröße 3 Ausführung Puffergröße 1 Ausführung Puffergröße 2 Ausführung Puffergröße 3 Lfd. Nr. Puffergröße Puffergröße Artikel-Nr. Abmessungen (mm) D x H / Gewinde M x L Abstand E Gewicht (kg) 1 1 234 101 045 100 x 50 / M 12 x 35 50 0,44 2 2 234 102 045 100 x 100 / M 12 x 35 50 0,67 3 3 234 103 045 100 x 150 / M 12 x 35 50 0,86 4 1 234 121 045 125 x 63 / M 12 x 35 63 0,64 5 2 234 122 045 125 x 125 / M 12 x 35 63 1,05 6 3 234 123 045 125 x 190 / M 12 x 35 63 1,45 7 1 234 161 045 160 x 80 / M 12 x 35 80 1,08 8 2 234 162 045 160 x 160 / M 12 x 35 80 1,93 9 3 234 163 045 160 x 240 / M 12 x 35 80 2,79 10 1 234 201 045 200 x 100 / M 12 x 35 100 2,17 11 2 234 202 045 200 x 200 / M 12 x 35 100 3,84 12 3 234 203 045 200 x 300 / M 12 x 35 100 5,51 13 1 234 251 045 250 x 125 / M 24 x 80 125 6,79 14 2 234 252 045 250 x 250 / M 24 x 80 125 9,89 15 3 234 253 045 250 x 375 / M 24 x 80 125 12,89 16 1 234 311 045 315 x 158 / M 24 x 80 160 9,89 17 2 234 312 045 315 x 315 / M 24 x 80 160 16,04 18 3 234 213 045 315 x 475 / M 24 x 80 160 22,19 19 1 234 401 045 400 x 200 / M 30 x 80 200 17,89 20 2 234 402 045 400 x 400 / M 30 x 80 200 30,49 21 3 234 403 045 400 x 600 / M 30 x 80 200 43,00 41
Titel Jäger Gummi und Kunststoff GmbH Bissendorfer Str. 6 30625 Hannover Germany +49 511 5358-0 +49 511 553394 info@jaeger-gk.de www.jaeger-gk.de Haftungsausschluss Wir schließen jegliche Haftung für die bereitgestellten Informationen und Produktdarstellungen aus. Für Inhalte technischer Art basieren diese auf dem Stand ihrer Veröffentlichung. Bestehende Urheber- und Namensrechte bleiben unberührt.