PRÄZISION Precision Tools in Solid Carbide High Performance Drills - Program Choices for your Production Präzisionswerkzeuge in Vollhartmetall - Hochleistungsbohrer Auswahlprogra für Ihre Fertigung HAM drill Drills for Highest Demands Vollhartmetall-Hochleistungsbohrer für höchste Ansprüche 3 Special Campaign Sonderaktion HAM Nirodrill Drills for Stainless Vollhartmetall-Hochleistungsbohrer für rostfreie Stähle HAM Deep Hole Drills The New Generation of Extra Long Solid Carbide Drills up to 40 x D Tieflochbohrer Die neue Generation der extra langen Vollhartmetall-Spiralbohrer bis 40 x D www.hamprecision.com
August-Schanz-Straße 21, 60433 Frankfurt am Main ZERTIFIKAT Die DQS GmbH Deutsche Gesellschaft zur Zertifizierung von Managementsystemen bescheinigt hiermit, dass das Unternehmen Hartmetallwerkzeugfabrik Andreas Maier GmbH Stegwiesen 2 88477 Schwendi-Hörenhausen ein Qualitätsmanagementsystem eingeführt hat und anwendet. Geltungsbereich: Entwicklung, Herstellung und Vertrieb von zeugsystemen, Standard- und Sonderwerkzeugen in Vollhartmetall-, Hartmetall-Composit, Cermet-, polykristallinen Diamant- und Keramikausführung, Dentalwerkzeuge, Zubehör und Dentalimplantaten Z E R T I F I K A T - E R G Ä N Z U N G Die DQS GmbH Deutsche Gesellschaft zur Zertifizierung von Managementsystemen zugelassen beim VERBAND DER AUTOMOBILINDUSTRIE e.v. (VDA) / Z.-Nr. 08-QMC-6.4-006 bescheinigt hiermit, dass das Unternehmen Durch ein Audit, dokumentiert in einem Bericht, wurde der Nachweis erbracht, dass das Managementsystem die Forderungen des folgenden Regelwerks erfüllt: ISO 9001 : 2008 Zertifikat-Registrier-Nr. 002949 QM08 Zertifizierungsdatum 2009-11-03 Gültig bis 2012-11-02 Michael Drechsel Jan Böge Geschäftsführer Geschäftsführer Hartmetallwerkzeugfabrik Andreas Maier GmbH Stegwiesen 2 88477 Schwendi-Hörenhausen für den Geltungsbereich Entwicklung, Herstellung und Vertrieb von zeugsystemen, Standard- und Sonderwerkzeugen in Vollhartmetall-, Cermet-, polykristallinen Diamant- und Keramikausführung für die Automobilindustrie ein Qualitätsmanagementsystem nach VDA 6, Teil 4 2. Auflage 2005 - Produktionsmittel - (mit Produktentwicklung) anwendet. Diese Zertifikatsergänzung ist nur gültig in Verbindung mit dem DQS-Zertifikat, Registrier-Nr. 002949 QM08. Sie bestätigt, dass das QM-System durch Erfüllung der in VDA 6, Teil 4 gegenüber ISO 9001:2008 erweiterten Forderungen zusätzlich qualifiziert ist. Der Nachweis wurde im Rahmen des Zertifizierungsaudits, Bericht-Nr. 002949, erbracht. Zertifizierungsaudit 2009-09-23 2009-09-25 Zertifizierungsentscheidung 2009-11-03 Dieses Zertifikatsergänzung ist gültig bis 2012-11-02 Registrier-Nr. 002949 A4 VDA QMC-Nr. 0001270 Frankfurt am Main 2009-11-03 HAM Develops and Manufactures Tools and Tooling-Systems for the Worldwide Market. Ass. iur. M. Drechsel Dipl.-Bw. J. Böge GESCHÄFTSFÜHRER D-60433 Frankfurt am Main, August-Schanz-Straße 21 (Tel. +49-69-95 42 70) HAM Your Competent Partner in the Precision Technology Solid Carbide, Cermets, Ceramic Tools for Drilling, Countersinking, Milling and Reaming Carbide, Diamond and CBN Tools with all modular Interfaces as Monoblock Tools, Indexable Inserts and Cartridge Tools (adjustable rough and precisely) for Drilling and Countersinking, for Milling and for Preand Precise Machining Project Planning and Project Engineering Worldwide TCM-partner for Tool Management Systems in Automotive and Aerospace Industry and their Suppliers Solid Carbide Drilling and Routing Tools for PCB Industry HAM is certified acc. to DIN EN ISO 9001, VDA 6.4. and DIN EN ISO 13485 HAM Entwickelt und Produziert zeuge und zeug-systeme für den Weltweiten Markt. HAM Ihr kompetenter Partner in der Präzisionswerkzeug-Technologie Vollhartmetall, Cermets, Keramik-zeuge zum Bohren, Senken, Fräsen und Reiben Hartmetall, Diamant- und CBN-zeuge mit allen modularen Schnittstellen als Monoblockwerkzeuge, Wendeplatten- und Kassettenwerkzeuge (grob und fein einstellbar) zum Bohren und Senken, zum Fräsen und für die Vor und Feinstbearbeitung Projektplanung und Projekt-Engineering Weltweiter TCM-Partner für Tool Management Systeme in der Automobil und Flugzeugindustrie und ihren Zulieferbetrieben Vollhartmetall-Bohr und Fräswerkzeuge für die Leiterplattenindustrie HAM ist zertifiziert nach DIN EN ISO 9001, VDA 6.4. und DIN EN ISO 13485 22
Page Content 4 Explanation of Icons in the Catalog Solid Carbide Spiral Drills - Aluminum,, Stainless, & Non-Ferrous 5 Non-Coolant - from dia. 1.00-10.00 6 Non-Coolant - from dia. 0.01-3.00 Solid Carbide -Drills - for, & Non-Ferrous 7 3 XD Coolant & Non-Coolant - from dia. 2.80-22.00 11 5 XD Coolant & Non-Coolant - from dia. 3.00-20.00 15 8 XD Coolant dia. 3.00-20.00 17 12 XD Coolant from dia. 3.00-12.00 Solid Carbide Niro-Drills - for Aluminum & Stainless & Non-Ferrous 18 3 XD Non-Coolant from dia. 2.80-16.00 19 5 XD Coolant from dia. 3.00-16.00 20 8 XD Coolant from dia. 3.00-16.00 Solid Carbide Multidrills - for Aluminim, & Non Ferrous 21 3 XD - 5 XD - 7 XD - Coolant from dia. 4.00-20.00 23 12 XD Coolant from dia. 4.00-16.00 24 Tap Drill & Countersink - Coolant from dia. 3.30-18.90 Solid Carbide Deep Hole Drills - for, Stainless & 26 5 XD - 8 XD - 12 XD - 15 XD - 20 XD - Coolant - from dia. 1.00-3.0 31 15 XD Coolant - from dia. 3.00-14.00 31 20 XD Coolant - from dia. 3.00-12.00 32 25 XD Coolant - from dia. 3.00-10.00 32 30 XD Coolant - from dia. 3.00-8.00 33 40 XD Coolant - from dia. 4.00-5.00 Solid Carbide Deep Hole Drills - for Aluminum & Non-Ferrous 33 15 XD Coolant - from dia. 3.00-14.00 34 20 XD Coolant - from dia. 3.00-12.00 34 25 XD Coolant - from dia. 3.00-10.00 35 30 XD Coolant - from dia. 3.00-7.00 35 40 XD Coolant - from dia. 4.00-5.00 36 HAM Cutting Data - Recoended Speeds & Feeds 4 Piktogra-Übersicht Vollhartmetall-Spiralbohrer - für Aluminium, Stahl, Inox, Gusseisen und NE-Metalle 5 Nicht Kühlmittel von dia. 1.00-10.00 6 Nicht Kühlmittel von dia. 0.01-3.00 Vollhartmetall-Bohrer Hochleistungsgs - für Stahl, Gusseisen und NE-Metalle 7 3 XD Kühlmittel & Nicht Kühlmittel von dia. 2.80-22.00 11 5 XD Kühlmittel & Nicht Kühlmittel von dia. 3.00-20.00 15 8 XD Kühlmittel von dia. 3.00-20.00 17 12 XD Kühlmittel von dia. 3.00-12.00 Vollhartmetall-Bohrer Niro Hochleistungs - für Aluminium, Stahl, Inox und NE-Metalle 18 3 XD Nicht Kühlmittel von dia. 2.80-16.00 19 5 XD Nicht Kühlmittel von dia. 3.00-16.00 20 8 XD Nicht Kühlmittel von dia. 3.00-16.00 Vollhartmetall-Bohrer Niro Hochleistungs - für Aluminium, Gusseisen und NE-Metalle 21 3 XD - 5 XD - 7 XD - Kühlmittel von dia. 4.00-20.00 23 12 XD Kühlmittel von dia. 4.00-16.00 24 Gewindebohrer und Senker - Kühlmittel von dia. 3.30-18.90 Vollhartmetall-Spiralbohrer der extra langen - für Stahl, Inox und Gusseisen 26 5 XD - 8 XD - 12 XD - 15 XD - 20 XD - Kühlmittel von dia. 1.00-3.00 31 15 XD Kühlmittel von dia. 3.00-14.00 31 20 XD Kühlmittel von dia. 3.00-12.00 32 25 XD Kühlmittel von dia. 3.00-10.00 32 30 XD Kühlmittel von dia. 3.00-8.00 33 40 XD Kühlmittel von dia. 4.00-5.00 Vollhartmetall-Spiralbohrer der extra langen - für Aluminum und NE-Metalle 33 15 XD Kühlmittel von dia. 3.00-14.00 34 20 XD Kühlmittel von dia. 3.00-12.00 34 25 XD Kühlmittel von dia. 3.00-10.00 35 30 XD Kühlmittel von dia. 3.00-7.00 35 40 XD Kühlmittel von dia. 4.00-5.00 36 HAM Schnittdaten - Empfohlenen Drehzahlen und Vorschübe 3
Explanation of Pictograms Piktogra-Übersicht Cutting Schneidstoff Solid Carbide Ultra Micro Grain Feinstkorn Vollhartmetall e N al al W For Soft s H Für Weiche stoffe For Hard s Für Harte stoffe HAM Standard snorm Number of Flutes Zähnezahl 2 Flutes 2 Flöten Standard HAM Standard morm DIN 6539 DIN 6537K DIN 6537 Cutting Length Schneidlänge 3 x D 3 x Diameter 3 x Durchmesser 5 x D 5 x Diameter 5 x Durchmesser 7 x D 7 x Diameter 7 x Durchmesser 8 x D 8 x Diameter 8 x Durchmesser 12 x D 12 x Diameter 12 x Durchmesser 15 x Diameter 20 x Diameter 15 x Durchmesser 20 x Durchmesser 15 x D 20 x D 25 x D 25 x Diameter 25 x Durchmesser 30 x Diameter 30 x Durchmesser 30 x D 40 x D 40 x Diameter 40 x Durchmesser Shank Shaft HA Cylindrical Shank acc. DIN Zylinderschaft nach DIN HB Clamping Fixture Weldon Spannfläche Weldnon HE Clamping Fixture Whistle Notch Spannfläche Whistle Notch HA Cylindrical Shank Zylinderschaft HAK Shank HA with IC Shaft HA with IC HBK Shank HB with IC Shaft HB with IC HEK Shank HE with IC Shaft HE with IC Shrink Fit Für Schrumpffutter Geeingnet Helix Angle Spiralwinkel 30 rechts 30 Right Hand Helix 30 Rechtsspirale 15 rechts 15 Right Hand Helix 15 Rechtsspirale 0 Nut 0 Helix 0 Rechtsspirale Point Angle Spitzenwinkel 130 137 140 Application Anwendung Form B Web Thinning Ausspitzung Interior Coolant Innenkühlung h6 Tolernance Toleranz H 7 Tolernance Toleranz MMS Mist Coolant External Spraykühlung Max. Thru Coolant Kühlmittel Durch None No Coolant Keine Kühlmittel High Performance Cutting 4
HAM 314 Solid Carbide Twist Drill 30 rechts 338 Vollhartmetall-Spiralbohrer DIN 4-facet ground thinning DIN 1412 form B web thickness reinforced AMS geometry 30 RH helix 4-Flächenanschliff Ausspitzung DIN 1412 Form B verstärkter Kern AMS Geometrie Spiralwinkel 30 30-1201 W 130 HA Composites MMS Max. None 30-1200 š š š š š š š š 30-1200 Twist drills are also available with coating, 30-1201 1.0 0.0394 10 12 34 1.0 1.1 0.0433 12 14 36 1.1 1.2 0.0472 13 16 38 1.2 1.3 0.0512 13 16 38 1.3 1.4 0.0551 15 18 40 1.4 1.5 0.0591 15 18 40 1.5 1.6 0.0630 17 20 43 1.6 1.7 0.0669 17 20 43 1.7 1.8 0.0709 18 22 46 1.8 1.9 0.0748 18 22 46 1.9 2.0 0.0787 20 24 49 2.0 2.1 0.0827 20 24 49 2.1 2.2 0.0866 22 27 53 2.2 2.3 0.0906 22 27 53 2.3 2.4 0.0945 25 30 57 2.4 2.5 0.0984 25 30 57 2.5 2.6 0.1024 25 30 57 2.6 2.7 0.1063 27 33 61 2.7 2.8 0.1102 27 33 61 2.8 2.9 0.1142 27 33 61 2.9 3.0 0.1181 27 33 61 3.0 3.1 0.1220 29 36 65 3.1 3.17 1/8 0.1250 29 36 65 3.17 3.2 0.1260 29 36 65 3.2 3.3 0.1299 29 36 65 3.3 3.4 0.1339 32 39 70 3.4 3.5 0.1378 32 39 70 3.5 3.57 9/64 0.1406 32 39 70 3.57 3.6 0.1417 32 39 70 3.6 3.7 0.1457 32 39 70 3.7 3.8 0.1496 35 43 75 3.8 3.9 0.1535 35 43 75 3.9 3.96 5/32 0.1563 35 43 75 3.96 4.0 0.1575 35 43 75 4.0 4.1 0.1614 35 43 75 4.1 4.2 0.1654 35 43 75 4.2 4.3 0.1693 38 47 80 4.3 30-1621 30-1200 Order example / Bestellbeispiel 30-1200-4 4.37 11/64 0.1719 38 47 80 4.37 4.4 0.1732 38 47 80 4.4 4.5 0.1772 38 47 80 4.5 4.6 0.1811 38 47 80 4.6 4.7 0.1850 42 52 86 4.7 4.76 3/16 0.1875 42 52 86 4.76 4.8 0.1890 42 52 86 4.8 4.9 0.1929 42 52 86 4.9 5.0 0.1969 42 52 86 5.0 5.1 0.2008 42 52 86 5.1 5.16 13/64 0.2031 42 52 86 5.16 5.2 0.2047 42 52 86 5.2 5.3 0.2087 42 52 86 5.3 5.4 0.2126 45 57 93 5.4 5.5 0.2165 45 57 93 5.5 5.55 7/32 0.2185 45 57 93 5.55 5.6 0.2205 45 57 93 5.6 5.7 0.2244 45 57 93 5.7 5.8 0.2283 45 57 93 5.8 5.9 0.2323 45 57 93 5.9 5.95 15/64 0.2344 45 57 93 5.95 6.0 0.2362 45 57 93 6.0 6.35 1/4 0.2500 50 63 101 6.35 6.5 0.2559 50 63 101 6.5 6.75 17/64 0.2656 50 63 101 6.75 7.0 0.2756 55 69 109 7.0 7.14 9/32 0.2812 55 69 109 7.14 7.54 16/64 0.2969 59 75 117 7.54 7.94 5/16 0.3125 59 75 117 7.94 8.0 0.3150 59 75 117 8.0 8.33 21/64 0.3281 63 81 125 8.33 8.73 11/32 0.3437 63 81 125 8.2 9.0 0.3543 63 81 125 9.0 9.13 23/64 0.3594 63 81 125 9.13 9.52 3/8 0.3750 67 87 133 9.52 10.0 0.3937 67 87 133 10.0 5
HAM Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 30 rechts 4-facet ground Ø 0.1-0.15 no web thinning Ø 0.2-0.45 web thinning DIN 1412 form A from Ø 0.5 web thinning DIN 1412 form C web thickness reinforced shank reinforced high concentricity 30 RH helix N 130 HA 4-Flächenanschliff Ø 0.1-0.15 ohne Ausspitzung Ø 0.2-0.45 Ausspitzung DIN 1412 form A ab Ø 0.5 Ausspitzung DIN 1412 form C verstärkter Kern verstärkter Schaft für hohe Rundlaufgenauigkeit Spiralwinkel 30 Composites MMS Max. None 30-1301 š š š 30-1301 TA 0.1 0.0039 0.5 1.5 38 3 0.15 0.0059 0.75 1.8 38 3 0.2 0.0079 1.0 2.4 38 3 0.25 0.0098 1.25 2.7 38 3 0.3 0.0118 1.5 3.0 38 3 0.35 0.0138 1.75 3.3 38 3 0.4 0.0157 2.0 3.6 38 3 0.45 0.0177 2.25 3.8 38 3 0.5 0.0197 2.5 4.0 38 3 0.55 0.0217 2.75 4.6 38 3 0.6 0.0236 3.0 4.8 38 3 0.65 0.0256 3.25 5.0 38 3 0.7 0.0276 3.5 6.0 38 3 0.75 0.0295 3.75 6.2 38 3 0.8 0.0315 4.0 6.4 38 3 0.85 0.0335 4.25 6.7 38 3 0.9 0.0354 4.5 7.0 38 3 0.95 0.0374 4.75 7.25 38 3 1.0 0.0394 5.0 7.5 38 3 1.05 0.0413 5.25 7.75 38 3 1.1 0.0433 5.5 8.0 38 3 1.15 0.0453 5.75 8.25 38 3 1.2 0.0472 6.0 8.5 38 3 1.25 0.0492 6.25 8.75 38 3 1.3 0.0512 6.5 9.0 38 3 1.35 0.0531 6.75 9.5 38 3 1.5 0.0551 7.0 10.0 38 3 1.45 0.0571 7.25 10.5 38 3 1.5 0.0591 7.5 11.0 38 3 1.55 0.0610 7.75 11.25 38 3 30-1301 TA 1.6 0.0630 8.0 11.5 38 3 1.65 0.0650 8.25 11.75 38 3 1.7 0.0669 8.5 12.0 38 3 1.75 0.0689 8.75 12.25 38 3 1.8 0.0709 9.0 12.5 38 3 1.85 0.0728 9.25 12.75 38 3 1.9 0.0748 9.5 13.0 38 3 1.95 0.0769 9.75 13.5 38 3 2.0 0.0787 10.0 14.0 46 4 2.05 0.0807 10.25 14.5 46 4 2.1 0.0827 10.5 15.0 46 4 2.15 0.0846 10.75 15.5 46 4 2.2 0.0866 11.0 16.0 46 4 2.25 0.0886 11.25 16.5 46 4 2.3 0.0906 11.5 17.0 46 4 2.35 0.0925 11.75 17.5 46 4 2.4 0.0945 12.0 18.0 46 4 2.45 0.0965 12.25 18.5 46 4 2.5 0.0984 12.5 19.0 46 4 2.55 0.1004 12.75 19.5 50 4 2.6 0.1024 13.0 20.0 50 4 2.65 0.1043 1325 20.5 50 4 2.7 0.1063 13.5 21.0 50 4 2.75 0.1083 13.75 21.5 50 4 2.8 0.1102 14.0 22.0 50 4 2.85 0.1122 14.25 22.5 50 4 2.9 0.1142 14.5 23.0 50 4 2.95 0.1161 14.75 23.5 50 4 3.0 0.1181 15.0 24.0 50 4 Order example / Bestellbeispiel 30-1301-1.6 6
HAM 280 drill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 3 x D 30 rechts DIN 6537K special point ground special chip flute geometry web thickness reinforced 30 RH helix 3 x D HA 140 HB HE spezielle Schneidkantenverrundung spezielle Spankaergeometrie verstärkter Kern Spiralwinkel 30 Composites MMS Max. None 30-1621 š š š š š š š 30-1621 2.8 0.1102 14 20 62 6 3.0 0.1181 14 20 62 6 3.1 0.1220 14 20 62 6 3.17 1/8 0.1250 14 20 62 6 3.2 0.1260 14 20 62 6 3.25 0.1280 14 20 62 6 3.3 0.1299 14 20 62 6 3.4 0.1339 14 20 62 6 3.5 0.1378 14 20 62 6 3.57 9/64 0.1406 14 20 62 6 3.6 0.1417 14 20 62 6 3.65 0.1437 14 20 62 6 3.7 0.1457 14 20 62 6 3.8 0.1496 17 24 66 6 3.9 0.1535 17 24 66 6 3.96 5/32 0.1563 17 24 66 6 4.0 0.1575 17 24 66 6 4.1 0.1614 17 24 66 6 4.2 0.1654 17 24 66 6 4.3 0.1693 17 24 66 6 4.37 11/64 0.1719 17 24 66 6 4.4 0.1732 17 24 66 6 4.5 0.1772 17 24 66 6 4.6 0.1811 17 24 66 6 4.65 0.1831 17 24 66 6 4.7 0.1850 20 28 66 6 4.76 3/16 0.1875 20 28 66 6 4.8 0.1890 20 28 66 6 4.9 0.1929 20 28 66 6 5.0 0.1969 20 28 66 6 5.1 0.2008 20 28 66 6 5.16 13/64 0.2031 20 28 66 6 5.2 0.2047 20 28 66 6 5.3 0.2087 20 28 66 6 5.4 0.2126 20 28 66 6 5.5 0.2165 20 28 66 6 5.55 7/32 0.2185 20 28 66 6 5.6 0.2205 20 28 66 6 5.7 0.2244 20 28 66 6 5.8 0.2283 20 28 66 6 5.9 0.2323 20 28 66 6 5.95 15/64 0.2344 20 28 66 6 6.0 0.2362 20 28 66 6 6.1 0.2402 24 34 79 8 6.2 0.2441 24 34 79 8 6.3 0.2480 24 34 79 8 6.35 1/4 0.2500 24 34 79 8 On request shank form HB or HE available without extra charge. 30-1621 6.4 0.2520 24 34 79 8 6.5 0.2559 24 34 79 8 6.6 0.2598 24 34 79 8 6.7 0.2638 24 34 79 8 6.75 17/64 0.2656 24 34 79 8 6.8 0.2677 24 34 79 8 6.9 0.2717 24 34 79 8 7.0 0.2756 24 34 79 8 7.1 0.2795 24 34 79 8 7.14 9/32 0.2812 29 41 79 8 7.2 0.2835 29 41 79 8 7.3 0.2874 29 41 79 8 7.4 0.2913 29 41 79 8 7.5 0.2953 29 41 79 8 7.54 19/64 0.2969 29 41 79 8 7.55 0.2972 29 41 79 8 7.6 0.2992 29 41 79 8 7.7 0.3031 29 41 79 8 7.8 0.3071 29 41 79 8 7.9 0.3110 29 41 79 8 7.94 5/16 0.3125 29 41 79 8 8.0 0.3150 29 41 79 8 8.1 0.3189 35 47 89 10 8.2 0.3228 35 47 89 10 8.3 0.3268 35 47 89 10 8.33 21/64 0.3281 35 47 89 10 8.4 0.3307 35 47 89 10 8.5 0.3346 35 47 89 10 8.6 0.3386 35 47 89 10 8.7 0.3425 35 47 89 10 8.73 11/32 0.3437 35 47 89 10 8.8 0.3465 35 47 89 10 8.9 0.3504 35 47 89 10 9.0 0.3543 35 47 89 10 9.1 0.3593 35 47 89 10 9.13 23/64 0.3594 35 47 89 10 9.2 0.3622 35 47 89 10 9.3 0.3661 35 47 89 10 9.4 0.3701 35 47 89 10 9.5 0.3740 35 47 89 10 9.52 3/8 0.3750 35 47 89 10 9.55 0.3760 35 47 89 10 9.6 0.3780 35 47 89 10 9.7 0.3819 35 47 89 10 9.8 0.3858 35 47 89 10 9.9 0.3898 35 47 89 10 9.92 25/64 0.3906 35 47 89 10 Order example / Bestellbeispiel HA-Shank / Schaft 30-1621-7,5 HB-Shank / Schaft 30-1621-7,5-HB HE-Shank / Schaft 30-1621-7,5-HE 7
30-1621 10.0 0.3937 40 55 102 12 10.1 0.3976 40 55 102 12 10.2 0.4016 40 55 102 12 10.3 0.4055 40 55 102 12 10.32 13/32 0.4062 40 55 102 12 10.4 0.4094 40 55 102 12 10.5 0.4134 40 55 102 12 10.6 0.4173 40 55 102 12 10.7 0.4213 40 55 102 12 10.72 27/64 0.4219 40 55 102 12 10.8 0.4252 40 55 102 12 10.9 0.4291 40 55 102 12 11.0 0.4331 40 55 102 12 11.1 0.4370 40 55 102 12 11.11 7/16 0.4375 40 55 102 12 11.2 0.4409 40 55 102 12 11.3 0.4449 40 55 102 12 11.4 0.4488 40 55 102 12 11.5 0.4528 40 55 102 12 11.51 29/64 0.4531 40 55 102 12 11.6 0.4567 40 55 102 12 11.7 0.4606 40 55 102 12 11.8 0.4645 40 55 102 12 11.9 0.4685 40 55 102 12 11.91 15/32 0.4687 40 55 102 12 Alle Preise in $ pro Stück / all price in $/pcs 12.0 0.4724 40 55 102 12 12.1 0.4764 43 60 107 14 12.2 0.4803 43 60 107 14 12.25 0.4823 43 60 107 14 12.3 0.4843 43 60 107 14 12.4 0.4882 43 60 107 14 12.5 0.4921 43 60 107 14 12.6 0.4961 43 60 107 14 12.7 1/2 0.5000 43 60 107 14 12.8 0.5039 43 60 107 14 12.9 0.5079 43 60 107 14 13.0 0.5118 43 60 107 14 13.1 0.5157 43 60 107 14 13.2 0.5197 43 60 107 14 On request shank form HB or HE available without extra charge. 30-1621 13.3 0.5236 43 60 107 14 13.4 0.5276 43 60 107 14 13.5 17/32 0.5315 43 60 107 14 13.6 0.5354 43 60 107 14 13.7 0.5394 43 60 107 14 13.8 0.5433 43 60 107 14 13.9 0.5472 43 60 107 14 14.0 0.5512 43 60 107 14 14.1 0.5551 45 65 115 16 14.2 0.5591 45 65 115 16 14.29 9/16 0.5625 45 65 115 16 14.3 0.5630 45 65 115 16 14.4 0.5669 45 65 115 16 14.5 0.5709 45 65 115 16 14.6 0.5748 45 65 115 16 14.7 0.5787 45 65 115 16 14.8 0.5827 45 65 115 16 14.9 0.5866 45 65 115 16 15.0 0.5906 45 65 115 16 15.1 0.5945 45 65 115 16 15.2 0.5984 45 65 115 16 15.3 0.6024 45 65 115 16 15.4 0.6063 45 65 115 16 15.5 0.6102 45 65 115 16 15.6 0.6142 45 65 115 16 15.7 0.6181 45 65 115 16 15.8 0.6220 45 65 115 16 15.88 5/8 0.6252 45 65 115 16 15.9 0.6260 45 65 115 16 16.0 0.6299 45 65 115 16 16.5 0.6496 51 73 123 18 17.0 0.6693 51 73 123 18 17.5 0.6890 51 73 123 18 18.0 0.7087 51 73 123 18 18.5 0.7283 55 79 131 20 19.0 0.7480 55 79 131 20 19.05 3/4 0.7500 55 79 131 20 19.5 0.7677 55 79 131 20 20.0 0.7874 55 79 131 20 Order example / Bestellbeispiel HA-Shank / Schaft 30-1621-7,5 HB-Shank / Schaft 30-1621-7,5-HB HE-Shank / Schaft 30-1621-7,5-HE 88
HAM 285 drill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 3 x D 30 rechts DIN 6537K special point ground special chip flute geometry web thickness reinforced 30 RH helix 3 x D HAK 140 HBK HEK spezielle Schneidkantenverrundung spezielle Spankaergeometrie verstärkter Kern Spiralwinkel 30 Composites MMS Max. None 30-1741 š š š š š š 30-1741 3.0 0.1181 14 20 62 6 3.1 0.1220 14 20 62 6 3.17 1/8 0.1250 14 20 62 6 3.2 0.1260 14 20 62 6 3.25 0.1280 14 20 62 6 3.3 0.1299 14 20 62 6 3.4 0.1339 14 20 62 6 3.5 0.1378 14 20 62 6 3.57 9/64 0.1406 14 20 62 6 3.6 0.1417 14 20 62 6 3.65 0.1437 14 20 62 6 3.7 0.1457 14 20 62 6 3.8 0.1496 17 24 66 6 3.9 0.1535 17 24 66 6 3.96 5/32 0.1563 17 24 66 6 4.0 0.1575 17 24 66 6 4.1 0.1614 17 24 66 6 4.2 0.1654 17 24 66 6 4.3 0.1693 17 24 66 6 4.37 11/64 0.1719 17 24 66 6 4.4 0.1732 17 24 66 6 4.5 0.1772 17 24 66 6 4.6 0.1811 17 24 66 6 4.65 0.1831 17 24 66 6 4.7 0.1850 20 28 66 6 4.76 3/16 0.1875 20 28 66 6 4.8 0.1890 20 28 66 6 4.9 0.1929 20 28 66 6 5.0 0.1969 20 28 66 6 5.1 0.2008 20 28 66 6 5.16 13/64 0.2031 20 28 66 6 5.2 0.2047 20 28 66 6 5.3 0.2087 20 28 66 6 5.4 0.2126 20 28 66 6 5.5 0.2165 20 28 66 6 5.55 7/32 0.2185 20 28 66 6 5.6 0.2205 20 28 66 6 5.7 0.2244 20 28 66 6 5.8 0.2283 20 28 66 6 5.9 0.2323 20 28 66 6 5.95 15/64 0.2344 20 28 66 6 6.0 0.2362 20 28 66 6 6.1 0.2402 24 34 79 8 6.2 0.2441 24 34 79 8 6.3 0.2480 24 34 79 8 6.35 1/4 0.2500 24 34 79 8 On request shank form HB or HE available without extra charge. 30-1621 30-1741 6.4 0.2520 24 34 79 8 6.5 0.2559 24 34 79 8 6.6 0.2598 24 34 79 8 6.7 0.2638 24 34 79 8 6.75 17/64 0.2656 24 34 79 8 6.8 0.2677 24 34 79 8 6.9 0.2717 24 34 79 8 7.0 0.2756 24 34 79 8 7.1 0.2795 24 34 79 8 7.14 9/32 0.2812 29 41 79 8 7.2 0.2835 29 41 79 8 7.3 0.2874 29 41 79 8 7.4 0.2913 29 41 79 8 7.5 0.2953 29 41 79 8 7.54 19/64 0.2969 29 41 79 8 7.55 0.2972 29 41 79 8 7.6 0.2992 29 41 79 8 7.7 0.3031 29 41 79 8 7.8 0.3071 29 41 79 8 7.9 0.3110 29 41 79 8 7.94 5/16 0.3125 29 41 79 8 8.0 0.3150 29 41 79 8 8.1 0.3189 35 47 89 10 8.2 0.3228 35 47 89 10 8.3 0.3268 35 47 89 10 8.33 21/64 0.3281 35 47 89 10 8.4 0.3307 35 47 89 10 8.5 0.3346 35 47 89 10 8.6 0.3386 35 47 89 10 8.7 0.3425 35 47 89 10 8.73 11/32 0.3437 35 47 89 10 8.8 0.3465 35 47 89 10 8.9 0.3504 35 47 89 10 9.0 0.3543 35 47 89 10 9.1 0.3593 35 47 89 10 9.13 23/64 0.3594 35 47 89 10 9.2 0.3622 35 47 89 10 9.3 0.3661 35 47 89 10 9.4 0.3701 35 47 89 10 9.5 0.3740 35 47 89 10 9.52 3/8 0.3750 35 47 89 10 9.55 0.3760 35 47 89 10 9.6 0.3780 35 47 89 10 9.7 0.3819 35 47 89 10 9.8 0.3858 35 47 89 10 9.9 0.3898 35 47 89 10 Order example / Bestellbeispiel HA-Shank / Schaft 30-1741-7,5 HB-Shank / Schaft 30-1741-7,5-HB HE-Shank / Schaft 30-1741-7,5-HE 9
30-1741 On request shank form HB or HE available without extra charge. 9.92 25/64 0.3906 35 47 89 10 10.0 0.3937 40 55 102 12 10.1 0.3976 40 55 102 12 10.2 0.4016 40 55 102 12 10.3 0.4055 40 55 102 12 10.32 13/32 0.4062 40 55 102 12 10.4 0.4094 40 55 102 12 10.5 0.4134 40 55 102 12 10.6 0.4173 40 55 102 12 10.7 0.4213 40 55 102 12 10.72 27/64 0.4219 40 55 102 12 10.8 0.4252 40 55 102 12 10.9 0.4291 40 55 102 12 11.0 0.4331 40 55 102 12 11.1 0.4370 40 55 102 12 11.11 7/16 0.4375 40 55 102 12 11.2 0.4409 40 55 102 12 11.3 0.4449 40 55 102 12 11.4 0.4488 40 55 102 12 11.5 0.4528 40 55 102 12 11.51 29/64 0.4531 40 55 102 12 11.6 0.4567 40 55 102 12 11.7 0.4606 40 55 102 12 11.8 0.4645 40 55 102 12 11.9 0.4685 40 55 102 12 11.91 15/32 0.4687 40 55 102 12 12.0 0.4724 40 55 102 12 12.1 0.4764 43 60 107 14 12.2 0.4803 43 60 107 14 12.25 0.4823 43 60 107 14 12.3 0.4843 43 60 107 14 12.4 0.4882 43 60 107 14 12.5 0.4921 43 60 107 14 12.6 0.4961 43 60 107 14 12.7 1/2 0.5000 43 60 107 14 12.8 0.5039 43 60 107 14 12.9 0.5079 43 60 107 14 13.0 0.5118 43 60 107 14 13.1 0.5157 43 60 107 14 13.2 0.5197 43 60 107 14 30-1741 Order example / Bestellbeispiel HA-Shank / Schaft 30-1741-10,2 HB-Shank / Schaft 30-1741-10,2-HB HE-Shank / Schaft 30-1741-10,2-HE 13.3 0.5236 43 60 107 14 13.4 0.5276 43 60 107 14 13.5 17/32 0.5315 43 60 107 14 13.6 0.5354 43 60 107 14 13.7 0.5394 43 60 107 14 13.8 0.5433 43 60 107 14 13.9 0.5472 43 60 107 14 14.0 0.5512 43 60 107 14 14.1 0.5551 45 65 115 16 14.2 0.5591 45 65 115 16 14.29 9/16 0.5625 45 65 115 16 14.3 0.5630 45 65 115 16 14.4 0.5669 45 65 115 16 14.5 0.5709 45 65 115 16 14.6 0.5748 45 65 115 16 14.7 0.5787 45 65 115 16 14.8 0.5827 45 65 115 16 14.9 0.5866 45 65 115 16 15.0 0.5906 45 65 115 16 15.1 0.5945 45 65 115 16 15.2 0.5984 45 65 115 16 15.3 0.6024 45 65 115 16 15.4 0.6063 45 65 115 16 15.5 0.6102 45 65 115 16 15.6 0.6142 45 65 115 16 15.7 0.6181 45 65 115 16 15.8 0.6220 45 65 115 16 15.88 5/8 0.6252 45 65 115 16 15.9 0.6260 45 65 115 16 16.0 0.6299 45 65 115 16 16.5 0.6496 51 73 123 18 17.0 0.6693 51 73 123 18 17.5 0.6890 51 73 123 18 18.0 0.7087 51 73 123 18 18.5 0.7283 55 79 131 20 19.0 0.7480 55 79 131 20 19.05 3/4 0.7500 55 79 131 20 19.5 0.7677 55 79 131 20 20.0 0.7874 55 79 131 20 22.0 0.8661 75 105 165 25 1010
HAM 283 drill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 5 x D 30 rechts DIN 6537 special point ground special chip flute geometry web thickness reinforced 30 RH helix 5 x D HA 140 HB HE spezielle Schneidkantenverrundung spezielle Spankaergeometrie verstärkter Kern Spiralwinkel 30 Composites MMS Max. None 30-1701 š š š š š š š 30-1701 3.0 0.1181 23 28 66 6 3.1 0.1220 23 28 66 6 3.17 1/8 0.1250 23 28 66 6 3.2 0.1260 23 28 66 6 3.25 0.1280 23 28 66 6 3.3 0.1299 23 28 66 6 3.4 0.1339 23 28 66 6 3.5 0.1378 23 28 66 6 3.57 9/64 0.1406 23 28 66 6 3.6 0.1417 23 28 66 6 3.65 0.1437 23 28 66 6 3.7 0.1457 23 28 66 6 3.8 0.1496 29 36 74 6 3.9 0.1535 29 36 74 6 3.96 5/32 0.1563 29 36 74 6 4.0 0.1575 29 36 74 6 4.1 0.1614 29 36 74 6 4.2 0.1654 29 36 74 6 4.3 0.1693 29 36 74 6 4.37 11/64 0.1719 29 36 74 6 4.4 0.1732 29 36 74 6 4.5 0.1772 29 36 74 6 4.6 0.1811 29 36 74 6 4.65 0.1831 29 36 74 6 4.7 0.1850 29 36 74 6 4.76 3/16 0.1875 35 44 82 6 4.8 0.1890 35 44 82 6 4.9 0.1929 35 44 82 6 5.0 0.1969 35 44 82 6 5.1 0.2008 35 44 82 6 5.16 13/64 0.2031 35 44 82 6 5.2 0.2047 35 44 82 6 5.3 0.2087 35 44 82 6 5.4 0.2126 35 44 82 6 5.5 0.2165 35 44 82 6 5.55 7/32 0.2185 35 44 82 6 5.6 0.2205 35 44 82 6 5.7 0.2244 35 44 82 6 5.8 0.2283 35 44 82 6 5.9 0.2323 35 44 82 6 5.95 15/64 0.2344 35 44 82 6 6.0 0.2362 35 44 82 6 6.1 0.2402 43 53 91 8 6.2 0.2441 43 53 91 8 6.3 0.2480 43 53 91 8 6.35 1/4 0.2500 43 53 91 8 On request shank form HB or HE available without extra charge. 30-1701 Order example / Bestellbeispiel HA-Shank / Schaft 30-1701-8 HB-Shank / Schaft 30-1701-8-HB HE-Shank / Schaft 30-1701-8-HE 6.4 0.2520 43 53 91 8 6.5 0.2559 43 53 91 8 6.6 0.2598 43 53 91 8 6.7 0.2638 43 53 91 8 6.75 17/64 0.2656 43 53 91 8 6.8 0.2677 43 53 91 8 6.9 0.2717 43 53 91 8 7.0 0.2756 43 53 91 8 7.1 0.2795 43 53 91 8 7.14 9/32 0.2812 43 53 91 8 7.2 0.2835 43 53 91 8 7.3 0.2874 43 53 91 8 7.4 0.2913 43 53 91 8 7.5 0.2953 43 53 91 8 7.54 19/64 0.2969 43 53 91 8 7.55 0.2972 43 53 91 8 7.6 0.2992 43 53 91 8 7.7 0.3031 43 53 91 8 7.8 0.3071 43 53 91 8 7.9 0.3110 43 53 91 8 7.94 5/16 0.3125 43 53 91 8 8.0 0.3150 43 53 91 8 8.1 0.3189 49 61 103 10 8.2 0.3228 49 61 103 10 8.3 0.3268 49 61 103 10 8.33 21/64 0.3281 49 61 103 10 8.4 0.3307 49 61 103 10 8.5 0.3346 49 61 103 10 8.6 0.3386 49 61 103 10 8.7 0.3425 49 61 103 10 8.73 11/32 0.3437 49 61 103 10 8.8 0.3465 49 61 103 10 8.9 0.3504 49 61 103 10 9.0 0.3543 49 61 103 10 9.1 0.3593 49 61 103 10 9.13 23/64 0.3594 49 61 103 10 9.2 0.3622 49 61 103 10 9.3 0.3661 49 61 103 10 9.4 0.3701 49 61 103 10 9.5 0.3740 49 61 103 10 9.52 3/8 0.3750 49 61 103 10 9.55 0.3760 49 61 103 10 9.6 0.3780 49 61 103 10 9.7 0.3819 49 61 103 10 9.8 0.3858 49 61 103 10 9.9 0.3896 49 61 103 10 11
30-1701 On request shank form HB or HE available without extra charge. 9.92 25/64 0.3906 49 61 103 10 10.0 0.3937 49 61 103 10 10.1 0.3976 56 71 118 12 10.2 0.4016 56 71 118 12 10.3 0.4055 56 71 118 12 10.32 13/32 0.4062 56 71 118 12 10.4 0.4094 56 71 118 12 10.5 0.4134 56 71 118 12 10.6 0.4173 56 71 118 12 10.7 0.4213 56 71 118 12 10.72 27/64 0.4219 56 71 118 12 10.8 0.4252 56 71 118 12 10.9 0.4291 56 71 118 12 11.0 0.4331 56 71 118 12 11.1 0.4370 56 71 118 12 11.11 7/16 0.4375 56 71 118 12 11.2 0.4409 56 71 118 12 11.3 0.4449 56 71 118 12 11.4 0.4488 56 71 118 12 11.5 0.4528 56 71 118 12 11.51 29/64 0.4531 56 71 118 12 11.6 0.4567 56 71 118 12 11.7 0.4606 56 71 118 12 11.8 0.4545 56 71 118 12 11.9 0.4685 56 71 118 12 11.91 15/32 0.4687 56 71 118 12 12.0 0.4724 56 71 118 12 12.1 0.4764 60 77 124 14 12.2 0.4803 60 77 124 14 12.25 0.4823 60 77 124 14 12.3 0.4843 60 77 124 14 12.4 0.4882 60 77 124 14 12.5 0.4921 60 77 124 14 12.6 0.4961 60 77 124 14 12.7 1/2 0.5000 60 77 124 14 12.8 0.5039 60 77 124 14 30-1701 Order example / Bestellbeispiel HA-Shank / Schaft 30-1701-10,2 HB-Shank / Schaft 30-1701-10,2-HB HE-Shank / Schaft 30-1701-10,2-HE 12.9 0.5079 60 77 124 14 13.0 0.5188 60 77 124 14 13.1 0.5157 60 77 124 14 13.2 0.5197 60 77 124 14 13.3 0.5236 60 77 124 14 13.4 0.5276 60 77 124 14 13.5 17/32 0.5315 60 77 124 14 13.6 0.5354 60 77 124 14 13.7 0.5394 60 77 124 14 13.8 0.5433 60 77 124 14 13.9 0.5472 60 77 124 14 14.0 0.5512 60 77 124 14 14.1 0.5551 63 83 133 16 14.2 0.5591 63 83 133 16 14.29 9/16 0.5625 63 83 133 16 14.3 0.5630 63 83 133 16 14.4 0.5669 63 83 133 16 14.5 0.5709 63 83 133 16 14.6 0.5748 63 83 133 16 14.7 0.5787 63 83 133 16 14.8 0.5827 63 83 133 16 14.9 0.5866 63 83 133 16 15.0 0.5906 63 83 133 16 15.1 0.5945 63 83 133 16 15.2 0.5984 63 83 133 16 15.3 0.6024 63 83 133 16 15.4 0.6063 63 83 133 16 15.5 0.6102 63 83 133 16 15.6 0.6142 63 83 133 16 15.7 0.6181 63 83 133 16 15.8 0.6220 63 83 133 16 15.88 5/8 0.6252 63 83 133 16 15.9 0.6260 63 83 133 16 16.0 0.6299 63 83 133 16 1212
HAM 286 drill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 5 x D 30 rechts DIN 6537 special point ground special chip flute geometry web thickness reinforced 30 RH helix spezielle Schneidkantenverrundung spezielle Spankaergeometrie verstärkter Kern Spiralwinkel 30 Composites MMS Max. None 30-1781 š š š š š š 5 x D HAK 140 HBK HEK 30-1781 3.0 0.1181 23 28 66 6 3.1 0.1220 23 28 66 6 3.17 1/8 0.1250 23 28 66 6 3.2 0.1260 23 28 66 6 3.25 0.1280 23 28 66 6 3.3 0.1299 23 28 66 6 3.4 0.1339 23 28 66 6 3.5 0.1378 23 28 66 6 3.57 9/64 0.1406 23 28 66 6 3.6 0.1417 23 28 66 6 3.65 0.1437 23 28 66 6 3.7 0.1457 23 28 66 6 3.8 0.1496 29 36 74 6 3.9 0.1535 29 36 74 6 3.96 5/32 0.1563 29 36 74 6 4.0 0.1575 29 36 74 6 4.1 0.1614 29 36 74 6 4.2 0.1654 29 36 74 6 4.3 0.1693 29 36 74 6 4.37 11/64 0.1719 29 36 74 6 4.4 0.1732 29 36 74 6 4.5 0.1772 29 36 74 6 4.6 0.1811 29 36 74 6 4.65 0.1831 29 36 74 6 4.7 0.1850 29 36 74 6 4.76 3/16 0.1875 35 44 82 6 4.8 0.1890 35 44 82 6 4.9 0.1929 35 44 82 6 5.0 0.1969 35 44 82 6 5.1 0.2008 35 44 82 6 5.16 13/64 0.2031 35 44 82 6 5.2 0.2047 35 44 82 6 5.3 0.2087 35 44 82 6 5.4 0.2126 35 44 82 6 5.5 0.2165 35 44 82 6 5.55 7/32 0.2185 35 44 82 6 5.6 0.2205 35 44 82 6 5.7 0.2244 35 44 82 6 5.8 0.2283 35 44 82 6 5.9 0.2323 35 44 82 6 5.95 15/64 0.2344 35 44 82 6 6.0 0.2362 35 44 82 6 6.1 0.2402 43 53 91 8 6.2 0.2441 43 53 91 8 6.3 0.2480 43 53 91 8 6.35 1/4 0.2500 43 53 91 8 On request shank form HB or HE available without extra charge. 30-1781 Order example / Bestellbeispiel HA-Shank / Schaft 30-1781-8 HB-Shank / Schaft 30-1781-8-HB HE-Shank / Schaft 30-1781-8-HE 6.4 0.2520 43 53 91 8 6.5 0.2559 43 53 91 8 6.6 0.2598 43 53 91 8 6.7 0.2638 43 53 91 8 6.75 17/64 0.2656 43 53 91 8 6.8 0.2677 43 53 91 8 6.9 0.2717 43 53 91 8 7.0 0.2756 43 53 91 8 7.1 0.2795 43 53 91 8 7.14 9/32 0.2812 43 53 91 8 7.2 0.2835 43 53 91 8 7.3 0.2874 43 53 91 8 7.4 0.2913 43 53 91 8 7.5 0.2953 43 53 91 8 7.54 19/64 0.2969 43 53 91 8 7.55 0.2972 43 53 91 8 7.6 0.2992 43 53 91 8 7.7 0.3031 43 53 91 8 7.8 0.3071 43 53 91 8 7.9 0.3110 43 53 91 8 7.94 5/16 0.3125 43 53 91 8 8.0 0.3150 43 53 91 8 8.1 0.3189 49 61 103 10 8.2 0.3228 49 61 103 10 8.3 0.3268 49 61 103 10 8.33 21/64 0.3281 49 61 103 10 8.4 0.3307 49 61 103 10 8.5 0.3346 49 61 103 10 8.6 0.3386 49 61 103 10 8.7 0.3425 49 61 103 10 8.73 11/32 0.3437 49 61 103 10 8.8 0.3465 49 61 103 10 8.9 0.3504 49 61 103 10 9.0 0.3543 49 61 103 10 9.1 0.3593 49 61 103 10 9.13 23/64 0.3594 49 61 103 10 9.2 0.3622 49 61 103 10 9.3 0.3661 49 61 103 10 9.4 0.3701 49 61 103 10 9.5 0.3740 49 61 103 10 9.52 3/8 0.3750 49 61 103 10 9.55 0.3760 49 61 103 10 9.6 0.3780 49 61 103 10 9.7 0.3819 49 61 103 10 9.8 0.3858 49 61 103 10 9.9 0.3898 49 61 103 10 13
30-1781 On request shank form HB or HE available without extra charge. 9.92 25/64 0.3605 49 61 103 10 10.0 0.3937 49 61 103 10 10.1 0.3976 56 71 118 12 10.2 0.4016 56 71 118 12 10.3 0.4055 56 71 118 12 10.32 13/32 0.4062 56 71 118 12 10.4 0.4094 56 71 118 12 10.5 0.4134 56 71 118 12 10.6 0.4173 56 71 118 12 10.7 0.4213 56 71 118 12 10.72 27/64 0.4219 56 71 118 12 10.8 0.4252 56 71 118 12 10.9 0.4291 56 71 118 12 11.0 0.4331 56 71 118 12 11.1 0.4370 56 71 118 12 11.11 7/16 0.4375 56 71 118 12 11.2 0.4409 56 71 118 12 11.3 0.4449 56 71 118 12 11.4 0.4488 56 71 118 12 11.5 0.4528 56 71 118 12 11.51 29/64 0.4531 56 71 118 12 11.6 0.4567 56 71 118 12 11.7 0.4606 56 71 118 12 11.8 0.4645 56 71 118 12 11.9 0.4685 56 71 118 12 11.91 15/32 0.4687 56 71 118 12 12.0 0.4724 56 71 118 12 12.1 0.4764 60 77 124 14 12.2 0.4803 60 77 124 14 12.25 0.4823 60 77 124 14 12.3 0.4843 60 77 124 14 12.4 0.4882 60 77 124 14 12.5 0.4921 60 77 124 14 12.6 0.4961 60 77 124 14 12.7 1/2 0.5000 60 77 124 14 12.8 0.5039 60 77 124 14 12.9 0.5079 60 77 124 14 13.0 0.5118 60 77 124 14 13.1 0.5157 60 77 124 14 13.2 0.5197 60 77 124 14 30-1781 Order example / Bestellbeispiel HA-Shank / Schaft 30-1781-10,2 HB-Shank / Schaft 30-1781-10,2-HB HE-Shank / Schaft 30-1781-10,2-HE 13.3 0.5236 60 77 124 14 13.4 0.5276 60 77 124 14 13.5 17/32 0.5315 60 77 124 14 13.6 0.5354 60 77 124 14 13.7 0.5394 60 77 124 14 13.8 0.5433 60 77 124 14 13.9 0.5472 60 77 124 14 14.0 0.5512 60 77 124 14 14.1 0.5551 63 83 133 16 14.2 0.5591 63 83 133 16 14.29 9/16 0.5625 63 83 133 16 14.3 0.5630 63 83 133 16 14.4 0.5669 63 83 133 16 14.5 0.5709 63 83 133 16 14.6 0.5748 63 83 133 16 14.7 0.5787 63 83 133 16 14.8 0.5827 63 83 133 16 14.9 0.5866 63 83 133 16 15.0 0.5906 63 83 133 16 15.1 0.5945 63 83 133 16 15.2 0.5984 63 83 133 16 15.3 0.6024 63 83 133 16 15.4 0.6063 63 83 133 16 15.5 0.6102 63 83 133 16 15.6 0.6142 63 83 133 16 15.7 0.6181 63 83 133 16 15.8 0.6220 63 83 133 16 15.88 5/8 0.6252 63 83 133 16 15.9 0.6260 63 83 133 16 16.0 0.6299 63 83 133 16 16.5 0.6496 71 93 143 18 17.0 0.6693 71 93 143 18 17.5 0.6890 71 93 143 18 18.0 0.7087 71 93 143 18 18.5 0.7283 77 101 153 20 19.0 0.7480 77 101 153 20 19.05 3/4 0.7500 77 101 153 20 19.5 0.7677 77 101 153 20 20.0 0.7874 77 101 153 20 1414
HAM 292 drill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 8 x D 30 rechts special point ground special chip flute geometry web thickness reinforced 30 RH helix spezielle Shneidkantenverrundung spezielle Spankaergeometrie verstärkter Kern Spiralwinkel 30 8 x D HAK 140 HBK HEK Dutcile Composites MMS Max. None 30-1821 š š š š š š 30-1821 3.0 0.1181 29 34 72 6 3.1 0.1220 29 34 72 6 3.17 1/8 0.1250 29 34 72 6 3.2 0.1260 29 34 72 6 3.25 0.1280 29 34 72 6 3.3 0.1299 29 34 72 6 3.4 0.1339 29 34 72 6 3.5 0.1378 29 34 72 6 3.57 9/64 0.1406 29 34 72 6 3.6 0.1417 29 34 72 6 3.65 0.1437 29 34 72 6 3.7 0.1457 29 34 72 6 3.8 0.1496 36 43 81 6 3.9 0.1535 36 43 81 6 3.96 5/32 0.1563 36 43 81 6 4.0 0.1575 36 43 81 6 4.1 0.1614 36 43 81 6 4.2 0.1654 36 43 81 6 4.3 0.1693 36 43 81 6 4.37 11/64 0.1719 36 43 81 6 4.4 0.1732 36 43 81 6 4.5 0.1772 36 43 81 6 4.6 0.1811 36 43 81 6 4.65 0.1831 36 43 81 6 4.7 0.1850 36 43 81 6 4.76 3/16 0.1875 48 57 95 6 4.8 0.1890 48 57 95 6 4.9 0.1929 48 57 95 6 5.0 0.1969 48 57 95 6 5.1 0.2008 48 57 95 6 5.16 13/64 0.2031 48 57 95 6 5.2 0.2047 48 57 95 6 5.3 0.2087 48 57 95 6 5.4 0.2126 48 57 95 6 5.5 0.2165 48 57 95 6 5.55 7/32 0.2185 48 57 95 6 5.6 0.2205 48 57 95 6 5.7 0.2244 48 57 95 6 5.8 0.2283 48 57 95 6 5.9 0.2323 48 57 95 6 5.95 15/64 0.2344 48 57 95 6 6.0 0.2362 48 57 95 6 6.1 0.2402 64 76 114 8 6.2 0.2441 64 76 114 8 6.3 0.2480 64 76 114 8 6.35 1/4 0.2500 64 76 114 8 On request shank form HB or HE available without extra charge. 30-1821 Order example / Bestellbeispiel HA-Shank / Schaft 30-1821-3 HB-Shank / Schaft 30-1821-3-HBK HE-Shank / Schaft 30-1821-3-HEK 6.4 0.2520 64 76 114 8 6.5 0.2559 64 76 114 8 6.6 0.2598 64 76 114 8 6.7 0.2638 64 76 114 8 6.75 17/64 0.2656 64 76 114 8 6.8 0.2677 64 76 114 8 6.9 0.2717 64 76 114 8 7.0 0.2756 66 76 116 8 7.1 0.2795 66 76 116 8 7.14 9/32 0.2812 66 76 116 8 7.2 0.2835 66 76 116 8 7.3 0.2874 66 76 116 8 7.4 0.2913 66 76 116 8 7.5 0.2953 66 76 116 8 7.54 19/64 0.2969 66 76 116 8 7.55 0.2972 66 76 116 8 7.6 0.2992 66 76 116 8 7.7 0.3031 66 76 116 8 7.8 0.3071 66 76 116 8 7.9 0.3110 66 76 116 8 7.94 5/16 0.3125 66 76 116 8 8.0 0.3150 66 76 116 8 8.1 0.3189 80 95 142 10 8.2 0.3228 80 95 142 10 8.3 0.3268 80 95 142 10 8.33 21/64 0.3281 80 95 142 10 8.4 0.3307 80 95 142 10 8.5 0.3346 80 95 142 10 8.6 0.3386 80 95 142 10 8.7 0.3425 80 95 142 10 8.73 11/32 0.3437 80 95 142 10 8.8 0.3465 80 95 142 10 8.9 0.3504 80 95 142 10 9.0 0.3543 80 95 142 10 9.1 0.3593 80 95 142 10 9.13 23/64 0.3594 80 95 142 10 9.2 0.3622 80 95 142 10 9.3 0.3661 80 95 142 10 9.4 0.3701 80 95 142 10 9.5 0.3740 80 95 142 10 9.52 3/8 0.3750 80 95 142 10 9.55 0.3760 80 95 142 10 9.6 0.3780 80 95 142 10 9.7 0.3819 80 95 142 10 9.8 0.3858 80 95 142 10 9.9 0.3898 80 95 142 10 15
30-1821 *Availability on request / Verfügbarkeit auf anfrage On request shank form HB or HE available without extra charge. 9.92 25/64 0.3605 80 95 142 10 10.0 0.3937 80 95 142 10 10.1 0.3976 96 114 162 12 10.2 0.4016 96 114 162 12 10.3 0.4055 96 114 162 12 10.32 13/32 0.4062 96 114 162 12 10.4 0.4094 96 114 162 12 10.5 0.4134 96 114 162 12 10.6 0.4173 96 114 162 12 10.7 0.4213 96 114 162 12 10.72 27/64 0.4219 96 114 162 12 10.8 0.4252 96 114 162 12 10.9 0.4291 96 114 162 12 11.0 0.4331 96 114 162 12 11.1 0.4370 96 114 162 12 11.11 7/16 0.4375 96 114 162 12 11.2 0.4409 96 114 162 12 11.3 0.4449 96 114 162 12 11.4 0.4488 96 114 162 12 11.5 0.4528 96 114 162 12 11.51 29/64 0.4531 96 114 162 12 11.6 0.4567 96 114 162 12 11.7 0.4606 96 114 162 12 11.8 0.4645 96 114 162 12 11.9 0.4685 96 114 162 12 11.91 15/32 0.4687 96 114 162 12 12.0 0.4724 96 114 162 12 12.1 0.4764 112 131 178 14 12.2 0.4803 112 131 178 14 12.25 0.4823 112 131 178 14 12.3 0.4843 112 131 178 14 12.4 0.4882 112 131 178 14 12.5 0.4921 112 131 178 14 12.6 0.4961 112 131 178 14 12.7 1/2 0.5000 112 131 178 14 12.8 0.5039 112 131 178 14 12.9 0.5079 112 131 178 14 13.0 0.5118 112 131 178 14 13.1 0.5157 112 131 178 14 13.2 0.5197 112 131 178 14 30-1821 13.3 0.5236 112 131 178 14 13.4 0.5276 112 131 178 14 13.5 17/32 0.5315 112 131 178 14 13.6 0.5354 112 131 178 14 13.7 0.5394 112 131 178 14 13.8 0.5433 112 131 178 14 13.9 0.5472 112 131 178 14 14.0 0.5512 112 131 178 14 14.1 0.5551 128 152 203 16 14.2 0.5591 128 152 203 16 14.29 9/16 0.5625 128 152 203 16 14.3 0.5630 128 152 203 16 14.4 0.5669 128 152 203 16 14.5 0.5709 128 152 203 16 14.6 0.5748 128 152 203 16 14.7 0.5787 128 152 203 16 14.8 0.5827 128 152 203 16 14.9 0.5866 128 152 203 16 15.0 0.5906 128 152 203 16 15.1 0.5945 128 152 203 16 15.2 0.5984 128 152 203 16 15.3 0.6024 128 152 203 16 15.4 0.6063 128 152 203 16 15.5 0.6102 128 152 203 16 15.6 0.6142 128 152 203 16 15.7 0.6181 128 152 203 16 15.8 0.6220 128 152 203 16 15.88 5/8 0.6252 128 152 203 16 15.9 0.6260 128 152 203 16 16.0 0.6299 128 152 203 16 16.5 0.6496 144 171 222 18 17.0 0.6693 144 171 222 18 17.5 0.6890 144 171 222 18 18.0 0.7087 144 171 222 18 18.5* 0.7283 160 190 243 20 19.0* 0.7480 160 190 243 20 19.05* 3/4 0.7500 160 190 243 20 19.5* 0.7677 160 190 243 20 20.0* 0.7874 160 190 243 20 Order example / Bestellbeispiel HA-Shank / Schaft 30-1821-10,2 HB-Shank / Schaft 30-1821-10,2-HB HE-Shank / Schaft 30-1821-10,2-HE 1616
HAM 293 drill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 12 x D 30 rechts 4 guide chamfer special point ground special chip flute geometry web thickness reinforced 30 RH helix 12 x D HAK 140 HBK HEK 4 Führungsfasen spezielle Schneidkantenverrundung spezielle Spankaergeometrie verstärkter Kern Spiralwinkel 30 Composites MMS Max. None 30-1861 š š š š š š 30-1861 3.0 0.1181 48 54 92 6 3.1 0.1220 48 54 92 6 3.17 1/8 0.1250 48 54 92 6 3.2 0.1260 48 54 92 6 3.25 0.1280 48 54 92 6 3.3 0.1299 48 54 92 6 3.4 0.1339 48 54 92 6 3.5 0.1378 48 54 92 6 3.57 9/64 0.1406 58 46 102 6 3.6 0.1417 58 46 102 6 3.65 0.1437 58 46 102 6 3.7 0.1457 58 46 102 6 3.8 0.1496 58 46 102 6 3.9 0.1535 58 46 102 6 3.96 5/32 0.1563 58 46 102 6 4.0 0.1575 58 46 102 6 4.1 0.1614 58 48 102 6 4.2 0.1654 58 48 102 6 4.3 0.1693 58 48 102 6 4.37 11/64 0.1719 58 48 102 6 4.4 0.1732 58 48 102 6 4.5 0.1772 58 48 102 6 4.6 0.1811 58 48 102 6 4.65 0.1831 58 48 102 6 4.7 0.1850 58 48 102 6 4.76 3/16 0.1875 58 48 102 6 4.8 0.1890 70 78 116 6 4.9 0.1929 70 78 116 6 5.0 0.1969 70 78 116 6 5.1 0.2008 70 78 116 6 5.16 13/64 0.2031 70 78 116 6 5.2 0.2047 70 78 116 6 5.3 0.2087 70 78 116 6 5.4 0.2126 70 78 116 6 5.5 0.2165 70 78 116 6 5.55 7/32 0.2185 70 78 116 6 5.6 0.2205 70 78 116 6 5.7 0.2244 70 78 116 6 5.8 0.2283 70 78 116 6 5.9 0.2323 70 78 116 6 5.95 15/64 0.2344 70 78 116 6 6.0 0.2362 70 78 1116 6 6.1 0.2402 70 78 116 6 6.2 0.2441 70 78 116 6 6.3 0.2480 94 108 146 8 6.35 1/4 0.2500 94 108 146 8 On request shank form HB or HE available without extra charge. 30-1861 Order example / Bestellbeispiel HA-Shank / Schaft 30-1861-3 HB-Shank / Schaft 30-1861-3-HBK HE-Shank / Schaft 30-1861-3-HEK 6.4 0.2520 94 108 146 8 6.5 0.2559 94 108 146 8 6.6 0.2598 94 108 146 8 6.7 0.2638 94 108 146 8 6.75 17/64 0.2656 94 108 146 8 6.8 0.2677 94 108 146 8 6.9 0.2717 94 108 146 8 7.0 0.2756 94 108 146 8 7.1 0.2795 94 108 146 8 7.14 9/32 0.2812 94 108 146 8 7.2 0.2835 94 108 146 8 7.3 0.2874 94 108 146 8 7.4 0.2913 94 108 146 8 7.5 0.2953 94 108 146 8 7.54 19/64 0.2969 94 108 146 8 7.55 0.2972 94 108 146 8 7.6 0.2992 94 108 146 8 7.7 0.3031 94 108 146 8 7.8 0.3071 94 108 146 8 7.9 0.3110 94 108 146 8 7.94 5/16 0.3125 94 108 146 8 8.0 0.3150 94 108 146 8 8.1 0.3189 110 120 162 10 8.2 0.3228 110 120 162 10 8.3 0.3268 110 120 162 10 8.33 21/64 0.3281 110 120 162 10 8.4 0.3307 110 120 162 10 8.5 0.3346 110 120 162 10 8.6 0.3386 110 120 162 10 8.7 0.3425 110 120 162 10 8.73 11/32 0.3437 110 120 162 10 8.8 0.3465 110 120 162 10 8.9 0.3504 110 120 162 10 9.0 0.3543 110 120 162 10 9.1 0.3593 110 120 162 10 9.13 23/64 0.3594 110 120 162 10 9.2 0.3622 110 120 162 10 9.3 0.3661 110 120 162 10 9.4 0.3701 110 120 162 10 9.5 0.3740 110 120 162 10 9.52 3/8 0.3750 110 120 162 10 9.55 0.3760 110 120 162 10 9.6 0.3780 110 120 162 10 9.7 0.3819 110 120 162 10 9.8 0.3858 110 120 162 10 9.9 0.3898 110 120 162 10 17
30-1861 Fractional sizes are available upon request. On request shank form HB or HE available without extra charge. 9.92 25/64 0.3605 110 120 162 10 10.0 0.3937 110 120 162 10 10.1 0.3976 142 156 204 12 10.2 0.4016 142 156 204 12 10.3 0.4055 142 156 204 12 10.32 13/32 0.4062 142 156 204 12 10.4 0.4094 142 156 204 12 10.5 0.4134 142 156 204 12 10.6 0.4173 142 156 204 12 10.7 0.4213 142 156 204 12 10.72 27/64 0.4219 142 156 204 12 10.8 0.4252 142 156 204 12 10.9 0.4291 142 156 204 12 11.0 0.4331 142 156 204 12 30-1861 11.1 0.4370 142 156 204 12 11.11 7/16 04375 142 156 204 12 11.2 0.4409 142 156 204 12 11.3 0.4449 142 156 204 12 11.4 0.4488 142 156 204 12 11.5 0.4528 142 156 204 12 11.51 29/64 0.4531 142 156 204 12 11.6 0.4567 142 156 204 12 11.7 0.4606 142 156 204 12 11.8 0.4546 142 156 204 12 11.9 0.4385 142 156 204 12 11.91 15/32 0.4687 142 156 204 12 12.00 0.4724 142 156 204 12 Order example / Bestellbeispiel HA-Shank / Schaft 30-1861-10,2 HB-Shank / Schaft 30-1861-10,2-HB HE-Shank / Schaft 30-1861-10,2-HE HAM Nirodrill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 3 x D 30 rechts DIN 6537K special chip flute geometry special point ground for machining of stainless steel 30 RH helix spezielle Spankaergeometrie Sonderanschliff zur Bearbeitung von nichtrostenden Stählen Spiralwinkel 30 3 x D HA 140 HB HE Composites MMS Max. None 30-1891 š š š š On request shank form HB or HE available without extra charge. 1818 30-1891 N 2.8 0.1102 14 20 62 6 3.0 0.1181 14 20 62 6 3.3 0.1299 14 20 62 6 3.5 0.1378 14 20 62 6 3.8 0.1496 17 24 66 6 4.0 0.1575 17 24 66 6 4.2 0.1654 17 24 66 6 4.3 0.1693 17 24 66 6 4.5 0.1772 17 24 66 6 5.0 0.1969 20 28 66 6 5.1 0.2008 20 28 66 6 5.5 0.2165 20 28 66 6 5.8 0.2283 20 28 66 6 6.0 0.2362 20 28 66 6 6.2 0.2441 24 34 79 8 6.5 0.2559 24 34 79 8 6.6 0.2598 24 34 79 8 6.8 0.2677 24 34 79 8 7.0 0.2756 24 34 79 8 7.5 0.2953 29 41 79 8 7.8 0.3071 29 41 79 8 30-1891 N 8.0 0.3159 29 41 79 8 8.5 0.3346 35 47 89 10 8.6 0.3386 35 47 89 10 8.8 0.3465 35 47 89 10 9.0 0.3543 35 47 89 10 9.5 0.3740 35 47 89 10 9.8 0.3858 35 47 89 10 10.0 0.3937 35 47 89 12 10.2 0.4016 40 55 102 12 10.5 0.4134 40 55 102 12 11.0 0.4331 40 55 102 12 11.2 0.4409 40 55 102 12 11.5 0.4528 40 55 102 12 11.8 0.4646 40 55 102 12 12.0 0.4724 40 55 102 12 13.0 0.5118 43 60 107 14 13.5 0.5315 43 60 107 14 13.8 0.5433 43 60 107 14 14.0 0.5512 43 60 107 14 15.0 0.5906 45 65 115 16 16.0 0.6299 45 65 115 16 Order example / Bestellbeispiel HA-Shank / Schaft 30-1891-8 HB-Shank / Schaft 30-1891-8-HB HE-Shank / Schaft 30-1891-8-HE
HAM 270 Nirodrill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 5 x D 30 rechts DIN 6537 special chip flute geometry special point ground for machining of stainless steel 30 RH helix 5 x D HAK 140 HBK HEK spezielle Spankaergeometrie Sonderanschliff zur Bearbeitung von nichtrostenden Stählen Spiralwinkel 30 Composites MMS max. None 30-1901 š š š š 30-1901 N Fractional sizes are available upon request. On request shank form HBK or HEK available without extra charge. 3.0 0.1181 23 28 66 6 3.1 0.1220 23 28 66 6 3.2 0.1260 23 28 66 6 3.3 0.1299 23 28 66 6 3.4 0.1339 23 28 66 6 3.5 0.1378 23 28 66 6 3.6 0.1417 23 28 66 6 3.7 0.1457 23 28 66 6 3.8 0.1496 29 36 74 6 3.9 0.1535 29 36 74 6 4.0 0.1575 29 36 74 6 4.1 0.1614 29 36 74 6 4.2 0.1654 29 36 74 6 4.3 0.1693 29 36 74 6 4.4.01732 29 36 74 6 4.5 0.1772 29 36 74 6 4.6 0.1811 29 36 74 6 4.7 0.1850 29 36 74 6 4.8 0.1890 35 44 82 6 4.9 0.1929 35 44 82 6 5.0 0.1969 35 44 82 6 5.1 0.2008 35 44 82 6 5.2 0.2047 35 44 82 6 5.3 0.2087 35 44 82 6 5.4 0.2126 35 44 82 6 5.5 0.2165 35 44 82 6 5.6 0.2205 35 44 82 6 5.7 0.2244 35 44 82 6 5.8 0.2283 35 44 82 6 5.9 0.2323 35 44 82 6 6.0 0.2362 35 44 82 6 6.1 0.2402 43 53 91 6 6.2 0.2441 43 53 91 6 6.3 0.2480 43 53 91 6 6.4 0.2520 43 53 91 6 6.5 0.2559 43 53 91 6 6.6 0.2598 43 53 91 6 6.7 0.2638 43 53 91 6 6.8 0.2677 43 53 91 6 6.9 0.2717 43 53 91 6 7.0 0.2756 43 53 91 6 7.1 0.2795 43 53 91 6 7.2 0.2835 43 53 91 8 7.3 0.2874 43 53 91 8 7.4 0.2913 43 53 91 8 7.5 0.2953 43 53 91 8 30-1901 N Order example / Bestellbeispiel HA-Shank / Schaft 30-1901-7,9 HB-Shank / Schaft 30-1901-7,9-HBK HE-Shank / Schaft 30-1901-7,9-HEK 7.6 0.2992 43 53 91 8 7.7 0.3031 43 53 91 8 7.8 0.3071 43 53 91 8 7.9 0.3110 43 53 91 8 8.0 0.3150 43 53 91 8 8.1 0.3189 49 61 103 10 8.2 0.3228 49 61 103 10 8.3 0.3268 49 61 103 10 8.4 0.3307 49 61 103 10 8.5 0.3346 49 61 103 10 8.6 0.3386 49 61 103 10 8.7 0.3425 49 61 103 10 8.8 0.3465 49 61 103 10 8.9 0.3504 49 61 103 10 9.0 0.3543 49 61 103 10 9.1 0.3593 49 61 103 10 9.2 0.3622 49 61 103 10 9.3 0.3661 49 61 103 10 9.4 0.3701 49 61 103 10 9.5 0.3740 49 61 103 10 9.6 0.3780 49 61 103 10 9.7 0.3819 49 61 103 10 9.8 03858 49 61 103 10 9.9 0.3898 49 61 103 10 10.0 0.3937 49 61 103 10 10.1 0.3976 56 71 118 12 10.2 0.4016 56 71 118 12 10.3 0.4055 56 71 118 12 10.4 0.4094 56 71 118 12 10.5 0.4134 56 71 118 12 10.6 0.4173 56 71 118 12 10.7 0.4213 56 71 118 12 10.8 0.4252 56 71 118 12 10.9 0.4291 56 71 118 12 11.0 0.4331 56 71 118 12 11.1 0.4370 56 71 118 12 11.2 0.4409 56 71 118 12 11.3 0.4449 56 71 118 12 11.4 0.4488 56 71 118 12 11.5 0.4528 56 71 118 12 11.6 0.4567 56 71 118 12 11.7 0.4606 56 71 118 12 11.8 0.4646 56 71 118 12 11.9 0.4685 56 71 118 12 12.0 0.4724 56 71 118 12 12.5 0.4921 60 77 124 14 19
30-1901 N 12.8 0.5039 60 77 124 14 13.0 0.5118 60 77 124 14 13.5 0.5315 60 77 124 14 13.8 0.5433 60 77 124 14 14.0 0.5512 60 77 124 14 14.5 0.5709 63 83 133 16 Fractional sizes are available upon request. 30-1901 N 14.8 0.5827 63 83 133 16 15.0 0.5906 63 83 133 16 15.1 0.5945 63 83 133 16 15.5 0.6102 63 83 133 16 15.8 0.6220 63 83 133 16 16.0 0.6299 63 83 133 16 Order example / Bestellbeispiel HA-Shank / Schaft 30-1901-12,8 HB-Shank / Schaft 30-1901-12,8 HBK HE-Shank / Schaft 30-1901-12,8-HEK HAM 271 Nirodrill Solid Carbide Twist Drill Vollhartmetall-Spiralbohrer 8 x D 30 rechts special chip flute geometry special point ground for machining of stainless steel 30 RH helix spezielle Spankaergeometrie Sonderanschliff zur Bearbeitung von nichtrostenden Stählen Spiralwinkel 30 2020 Composites MMS Max. None 30-1941 š š š š 30-1941 N 3.0 0.1181 29 34 72 6 3.1 0.1220 29 34 72 6 3.2 0.1260 29 34 72 6 3.3 0.1299 29 34 72 6 3.4 0.1339 29 34 72 6 3.5 0.1378 29 34 72 6 3.6 0.1417 29 34 72 6 3.7 0.1457 29 34 72 6 3.8 0.1496 36 43 81 6 3.9 0.1535 36 43 81 6 4.0 0.1575 36 43 81 6 4.1 0.1614 36 43 81 6 4.2 0.1654 36 43 81 6 4.3 0.1693 36 43 81 6 4.4 0.1732 36 43 81 6 4.5 0.1772 36 43 81 6 4.6 0.1811 36 43 81 6 4.7 0.1850 36 43 81 6 4.8 0.1890 48 57 95 6 4.9 0.1929 48 57 95 6 5.0 0.1969 48 57 95 6 5.1 0.2008 48 57 95 6 5.2 0.2047 48 57 95 6 5.3 0.2087 48 57 95 6 5.4 0.2126 48 57 95 6 5.5 0.2165 48 57 95 6 5.6 0.2205 48 57 95 6 5.7 0.2244 48 57 95 6 5.8 0.2286 48 57 95 6 5.9 0.2323 48 57 95 6 6.0 0.2362 48 57 95 6 30-1941 N 8 x D HAK 140 HBK HEK 6.1 0.2402 64 76 114 8 6.2 0.2441 64 76 114 8 6.3 0.2480 64 76 114 8 6.4 0.2520 64 76 114 8 6.5 0.2559 64 76 114 8 6.6 0.2598 64 76 114 8 6.7 0.2638 64 76 114 8 6.8 0.2677 64 76 114 8 6.9 0.2717 64 76 114 8 7.0 0.2756 64 76 114 8 7.1 0.2795 64 76 114 8 7.2 0.2835 64 76 114 8 7.3 0.2874 64 76 114 8 7.4 0.2913 64 76 114 8 7.5 0.2953 64 76 114 8 7.6 0.2992 64 76 114 8 7.7 0.3031 64 76 114 8 7.8 0.3071 64 76 114 8 7.9 0.3110 64 76 114 8 8.0 0.3150 64 95 142 10 8.1 0.3189 80 95 142 10 8.2 0.3228 80 95 142 10 8.3 0.3268 80 95 142 10 8.4 0.3307 80 95 142 10 8.5 0.3346 80 95 142 10 8.6 0.3386 80 95 142 10 8.7 0.3425 80 95 142 10 8.8 0.3465 80 95 142 10 8.9 0.3504 80 95 142 10 9.0 0.3543 80 95 142 10 9.1 0.3593 80 95 142 10 Order example / Bestellbeispiel HA-Shank / Schaft 30-1941-7,7 Fractional sizes are available upon request HB-Shank / Schaft 30-1941-7,7-HBK On request shank form HBK or HEK available without extra charge. HE-Shank / Schaft 30-1941-7,7-HEK
30-1941 N 9.2 0.3622 80 95 142 10 9.3 0.3661 80 95 142 10 9.4 0.3701 80 95 142 10 9.5 0.3740 80 95 142 10 9.6 0.3780 80 95 142 10 9.7 0.3819 80 95 142 10 9.8 0.3858 80 95 142 10 9.9 0.3898 80 95 142 10 10.0 0.3937 80 95 142 10 10.1 0.3976 96 114 162 12 10.2 0.4016 96 114 162 12 10.3 0.4055 96 114 162 12 10.4 0.4094 96 114 162 12 10.5 0.4134 96 114 162 12 10.6 0.4173 96 114 162 12 10.7 0.4213 96 114 162 12 10.8 0.4252 96 114 162 12 10.9 0.4219 96 114 162 12 11.0 0.4331 96 114 162 12 11.1 0.4370 96 114 162 12 11.2 0.4409 96 114 162 12 Order example / Bestellbeispiel HA-Shank / Schaft 30-1941-7,7 Fractional sizes are available upon request. HB-Shank / Schaft 30-1941-7,7-HBK On request shank form HBK or HEK available without extra charge. HE-Shank / Schaft 30-1941-7,7-HEK 30-1941 N 11.3 0.4449 96 114 162 12 11.4 0.4488 96 114 162 12 11.5 0.4528 96 114 162 12 11.6 0.4567 96 114 162 12 11.7 0.4606 96 114 162 12 11.8 0.4646 96 114 162 12 11.9 0.4685 96 114 162 12 12.0 0.4724 96 114 162 12 12.5 0.4921 112 131 178 14 12.8 0.5039 112 131 178 14 13.0 0.5118 112 131 178 14 13.5 05315 112 131 178 14 13.8 0.5433 112 131 178 14 14.0 0.5512 112 131 178 14 14.5 0.5709 128 155 203 14 14.8 0.5827 128 152 203 16 15.0 0.5906 128 152 203 16 15.5 0.6102 128 152 203 16 15.8 0.6220 128 152 203 16 16.0 0.6299 128 152 203 16 HAM 297 Multidrill Solid Carbide Drill Vollhartmetall-Spiralbohrer 3 x D 0 Nut 4-facet ground straight fluted for machining of short chipping materials 4 Flächenanschliff gerade genutet zur Bearbeitung kurzspanender stoffe 30-1961 3 x D 140 HBK HAK HEK Composites MMS Max. None 30-1960 š 30-1960 4.0 0.1575 17 24 66 6 4.2 0.1654 17 24 66 6 4.76 3/16 0.1874 17 24 66 6 5.0 0.1969 20 28 66 6 6.0 0.2362 20 28 66 6 6.35 1/4 0.2500 24 34 79 8 6.8 0.2677 24 34 79 8 7.0 0.2756 24 34 79 8 7.94 5/16 0.3126 24 40 79 8 8.0 0.3150 29 41 79 8 8.5 0.3346 35 47 89 10 9.0 0.3543 35 47 89 10 9.52 3/8 0.3748 35 47 89 10 10.0 0.3937 35 47 89 10 Multidrills are also available with coating, 30-1961 30-1960 Order example / Bestellbeispiel HA-Shank / Schaft 30-1960-10,2 HB-Shank / Schaft 30-1960-10,2 HBK HE-Shank / Schaft 30-1960-10,2-HEK 10.2 0.4016 40 55 102 12 10.5 0.4134 40 55 102 12 11.0 0.4331 40 55 102 12 11.11 7/16 0.4374 40 55 102 12 12.0 0.4724 40 55 102 12 12.7 1/2 0.5000 43 60 107 14 14.0 0.5512 43 60 107 14 14.29 9/16 0.5626 45 65 115 16 15.88 5/8 0.6248 45 65 115 16 16.0 0.6299 45 65 115 16 18.0 0.7087 51 73 123 18 19.05 3/4 0.7500 55 79 131 20 20.0 0.7874 55 79 131 20 21
HAM 298 Multidrill Solid Carbide Drill Vollhartmetall-Spiralbohrer 5 x D 0 Nut 4-facet ground straight fluted for machining of short chipping materials 4 Flächenanschliff gerade genutet zur Bearbeitung kurzspanender stoffe 30-2001 5 x D 140 HBK HAK HEK Composites MMS Max. None 30-2000 š 30-2000 4.0 0.1575 29 36 74 6 4.2 0.1654 29 36 74 6 4.76 3/16 0.1874 35 44 82 6 5.0 0.1969 35 44 82 6 6.0 0.2362 35 44 82 6 6.35 1/4 0.2500 43 53 91 8 6.8 0.2677 43 53 91 8 7.0 0.2756 43 53 91 8 7.94 5/16 0.3126 43 53 91 8 8.0 0.3150 43 53 91 8 8.5 0.3346 49 61 103 10 9.0 0.3543 49 61 103 10 9.52 3/8 0.3748 49 61 103 10 10.0 0.3937 49 61 103 10 Multidrills are also available with coating, 30-2001 30-2000 Order example / Bestellbeispiel HA-Shank / Schaft 30-2000-10,2 HB-Shank / Schaft 30-2000-10,2 HBK HE-Shank / Schaft 30-2000-10,2-HEK 10.2 0.4016 56 71 118 12 10.5 0.4134 56 71 118 12 11.0 0.4331 56 71 118 12 11.11 7/16 0.4374 56 71 118 12 12.0 0.4724 56 71 118 12 12.7 1/2 0.5000 60 77 124 14 14.0 0.5512 60 77 124 14 14.29 9/16 0.5626 63 83 133 16 15.88 5/8 0.6248 63 83 133 16 16.0 0.6299 63 83 133 16 18.0 0.7087 71 83 143 18 19.05 3/4 0.7500 77 101 153 20 20.0 0.7874 77 101 153 20 HAM 299 Multidrill Solid Carbide Drill Vollhartmetall-Spiralbohrer 7 x D 0 Nut 4-facet ground straight fluted for machining of short chipping materials 4 Flächenanschliff gerade genutet zur Bearbeitung kurzspanender stoffe 30-2041 7 x D 140 HBK HAK HEK Composites MMS Max. None 30-2040 š 30-2040 4.0 0.1575 28 37 78 6 4.2 0.1654 28 37 78 6 4.76 3/16 0.1874 35 49 88 6 Multidrills are also available with coating, 30-2041 30-2040 Order example / Bestellbeispiel HA-Shank / Schaft 30-2041-10,2 HB-Shank / Schaft 30-2041-10,2 HBK HE-Shank / Schaft 30-2041-10,2-HEK 5.0 0.1969 35 49 88 6 6.0 0.2362 35 49 88 6 6.35 1/4 0.2500 48 66 104 8 2222
30-2040 6.8 0.2677 48 66 104 8 7.0 0.2756 48 66 104 8 7.94 5/16 0.3125 48 66 104 8 8.0 0.3150 48 66 104 8 8.5 0.3346 70 98 140 10 9.0 0.3543 70 98 140 10 9.52 3/8 0.3748 70 98 140 10 10.0 0.3937 70 98 140 10 10.2 0.4016 74 98 145 12 10.5 0.4134 74 98 145 12 11.0 0.4331 74 98 145 12 30-2040 11.11 7/16 0.4374 74 98 145 12 12.0 0.4724 74 98 145 12 12.7 1/2 0.5000 98 114 161 14 14.0 0.5512 98 114 161 14 14.29 9/16 0.5626 112 131 181 16 15.87 5/8 0.6248 112 131 181 16 16.0 0.6299 112 131 181 16 18.0 0.7087 126 147 197 18 19.05 3/4 0.7500 140 164 216 20 20.0 0.7874 140 164 216 20 Multidrills are also available with coating, 30-2041 Order example / Bestellbeispiel HA-Shank / Schaft 30-2040-12,8 HB-Shank / Schaft 30-2040-12,8 HBK HE-Shank / Schaft 30-2040-12,8-HEK HAM 294 Multidrill Solid Carbide Drill Vollhartmetall-Spiralbohrer 12 x D 0 Nut 4-facet ground straight fluted for machining of short chipping materials 4 Flächenanschliff gerade genutet zur Bearbeitung kurzspanender stoffe 30-2081 12 x D 140 HBK HAK HEK Composites MMS Max. None 30-2080 š 30-2080 4.0 0.1575 58 77 121 6 4.2 0.1654 58 77 121 6 4.5 0.1772 58 77 121 6 4.76 3/16 0.1874 70 82 121 6 5.0 0.1969 70 82 121 6 5.5 0.2165 70 82 121 6 6.0 0.2362 70 82 121 6 6.35 1/4 0.2500 94 106 146 8 6.5 0.2559 94 106 146 8 6.8 0.2677 94 106 146 8 7.0 0.2756 94 106 146 8 7.5 0.2953 94 106 146 8 7.8 0.3071 94 106 146 8 7.94 5/16 0.3126 94 106 146 8 8.0 0.3150 94 106 146 8 8.5 0.3346 110 130 175 10 9.0 0.3543 110 130 175 10 9.5 0.3740 110 130 175 10 9.52 3/8 0.3748 110 130 175 10 Multidrills are also available with coating, 30-2081 30-2080 Order example / Bestellbeispiel HA-Shank / Schaft 30-2080-10,2 HB-Shank / Schaft 30-2080-10,2 HBK HE-Shank / Schaft 30-2081-10,2-HEK 10.0 0.3937 110 130 175 10 10.2 0.4016 142 159 209 12 10.5 0.4134 142 159 209 12 11.0 0.4331 142 159 209 12 11.11 7/16 0.4374 142 159 209 12 11.5 0.4528 142 159 209 12 12.0 0.4724 142 159 209 12 12.5 0.4921 166 183 233 14 12.7 1/2 0.500 166 183 233 14 13.0 0.5118 166 183 233 14 13.5 0.5315 166 183 233 14 14.0 0.5512 166 183 233 14 14.29 9/16 0.5626 192 207 260 16 14.5 0.5709 192 207 260 16 15.0 0.5906 192 207 260 16 15.5 0.6102 192 207 260 16 15.87 5/8 0.6248 192 207 260 16 16.0 0.6299 192 207 260 16 23
HAM 296 Multidrill Solid Carbide Step Drill Vollhartmetall-Stufenbohrer 0 Nut 4-facet ground straight fluted for machining of short chipping materials for machining of thread core holes cutting till countersinking step 4 Flächenanschliff gerade genutet zur Bearbeitung kurzspanender stoffe zur Herstellung von Gewindekernlöcher schneidend bis inklusive Senkstufe 90 d3 140 HBK HAK HEK Composites MMS Max. None 30-2120 š 30-2120 Tap Size Ø d3 3.3 M4 - GS 0.1299 11.4 25 62 6 6 3.65 M4 - GF 0.1437 11.4 25 62 6 6 4.2 M5 - GS 0.1654 13.6 28 66 6 6 4.65 M5 - GF 0.1831 13.6 28 66 6 6 5.0 M6 - GS 0.1969 16.5 34 79 8 8 5.55 M6 - GF 0.2185 16.5 34 79 8 8 6.8 M8 - GS 0.2677 21.0 47 79 10 10 7.4 M8 - GF 0.2913 21.0 47 79 10 10 8.5 M10 - GS 0.3346 25.5 55 79 12 12 9.35 M10 - GF 0.3681 25.5 55 79 12 12 30-2120 Tap Size Order example / Bestellbeispiel HA-Shank / Schaft 30-2120-10,2 HB-Shank / Schaft 30-2120-10,2 HBK HE-Shank / Schaft 30-2120-10,2-HEK Ø d3 10.2 M12 - GS 0.4016 30.0 60 107 14 14 11.2 M12 - GF 0.4409 30.0 60 107 14 14 12.0 M14 - GS 0.4724 34.5 65 115 16 16 13.2 M14 - GF 0.5197 34.5 65 115 16 16 14.0 M16 - GS 0.5512 38.5 73 123 18 18 15.1 M16 - GF 0.5945 38.5 73 123 18 18 15.5 M18 - GS 0.6102 43.5 79 131 20 20 16.9 M18 - GF 0.6654 43.5 79 131 20 20 17.5 M20 - GS 0.6890 47.5 89 147 22 20 18.9 M20 - GF 0.7441 47.5 89 147 22 20 2424
Requirement: High Concentricity of the Spindle Enough Coolant Pressure Voraussetzung: Hohe Rundlaufgenauigkeit der Spindel Ausreichender Kühlmitteldruck Recoendation for Using the Deep Hole Drills 12 to 40 x Diameter Drilling a pilot hole with HAM drill or HAM Multidrill for aluminium (tolerance m7) 1 to 1.5 x D Run with the deep hole drill into the pilot hole with low speed and feed rates Start cooling Increase speed and feed rate Machine the deep hole in one step Life the drill, reduce speed and feed, stop cooling and extend the drill Einsatzempfehlung für Tieflochbohrer mit Bohrtiefe 12 bis 40 x D Pilotbohrung mit HAM drill oder HAM Multidrill für aluminium (Durchmessertoleranz m7) mit einer bohrtiefe von 1 bis 1.5 x D Tiefl ochbohrer mit geringer drehzahl in die pilotbohrung einfahren Kühlmittelzufuhr starten Bohrvorgang mit empfohlenen schnittwerten durchführen Tieflochbohren ohne entspänen Nach erreichter bohrtiefe tieflochbohrer anheben, drehzahl reduzieren, kühlmittelzufuhr unterbrechen und ausfahren 25