User Manual Benutzerhandbuch Manuel Utilisateur Manuale d uso USB 2.0 Cat.5 Extender 100m 7 Port for 2 PCs English Deutsch Français Italiano LINDY No. 42695 www.lindy.com Tested to Comply with FCC Standards For Home and Office Use! LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (May 2015)
Introduction Thank you for purchasing the LINDY USB 2.0 Cat.5 Extender for 2 PCs. This extender is composed of a transmitting unit with 3 USB ports and a receiving unit with 7 USB ports and enables two USB host devices to send data up to 100 metres. Package Contents Local/Transmitter Unit Receiver Unit Multi-Country Power Supply 5V DC 2A for local unit Multi-Country Power Supply 5V DC 3.5A for receiver unit 2 USB Cables Four assembly brackets LINDY Manual Features True plug and play, no driver installation required This USB 2.0 Cat.5 Extender can be shared by two PCs Local unit with 3 Port USB 2.0 hub, remote unit with 7 port USB 2.0 hub Extends USB 2.0 high-speed and USB 1.1 (low-speed, full-speed) devices up to 100m over Cat 5e (or better) cable. Supports all USB device types: Control, Interrupt, Bulk and Isochronous at up to 480Mbps Supports all major operating systems with USB support Switching between computers by push button Installation 1. Place the local extender near the computer(s). Install the supplied USB cable between the local extender and USB port on the host computer(s). USB Type B connectors are used to connect the local extender unit to the host computer. 2. Connect the supplied 5VDC 2A power adapter to the local unit. 3. Place the remote extender near the USB device(s) in the desired remote location. 4. Connect the supplied 5VDC 3.5A power adapter to the remote unit. 5. Connect the local to the remote extender by using a Cat.5 (or better) cable (not included!). To switch between the two PCs, please push the button on the transmitter and wait about 5 seconds. LED indications Power LED on transmitter: power supply is on; on receiver: lights only when PC is on Active: USB device is connected Link: transmitter and receiver are connected by Cat.5 (or higher) cable USB ports on transmitter/receiver: respective LED lights when device is connected PC1/PC2: shows which PC is active [1]
Einleitung Vielen Dank für den Kauf des LINDY USB 2.0 Cat.5 Extenders für 2 PCs. Dieser besteht aus einer Sendeeinheit mit 3 USB Ports und einer Empfangseinheit mit 7 USB Ports. Er ermöglicht es zwei USB Hosts Daten über eine Distanz von bis zu 100 Metern zu senden. Lieferumfang Sende- und Empfangseinheit Multi-Country Netzteil 5V DC 2A für den Sender Multi-Country Netzteil 5V DC 3.5A für den Empfänger 2 USB Kabel Vier Montagewinkel Dieses Handbuch Eigenschaften Plug & Play, Treiberinstallation ist nicht erforderlich An den Sender des USB 2.0 Cat.5 Extenders können zwei Computer angeschlossen werden Sendeeinheit mit 3 Port USB 2.0 Hub, Empfangseinheit mit 7 Port USB 2.0 Hub Unterstützt USB 2.0 high-speed und USB 1.1 (low-speed, full-speed) bis zu einer Entfernung von 100m über Cat 5e (oder höher) Kabel.. Unterstützt alle Arten von USB Devices: Kontroll-, Interrupt, Bulk- und isochrone Transfers bis 480Mbit/S. Betriebssystemunabhängig Umschalten zwischen zwei Computern per Knopfdruck Installation 1. Schließen Sie die Sendeeinheit des Extenders mit dem/den beiliegenden USB Kabeln an einem bzw. zwei Computer/n an (zum Verbinden der Sendeeinheit mit dem Host Computer werden USB Typ B Stecker verwendet). 2. Schließen Sie das beiliegende 5VDC 2A Netzteil ebenfalls an der Sendeeinheit an.. 3. Die Empfangseinheit des Extenders platzieren Sie in der gwünschten, bis zu 100m entfernten Position. 4. Schließen Sie das beiliegende 5VDC 3.5A Netzteil am Empfänger an. 5. Verbinden Sie dann Sender und Empfänger über ein Cat.5 (oder höher) Kabel (nicht im Lieferumfang enthalten!). Zum Umschalten zwischen den 2 Computern drücken Sie bitte auf den Schalter auf der Sendeeinheit und warten ca. 5 Sekunden. LED Anzeigen Power LED beim Sender: das Netzteil ist eingeschaltet, beim Empfänger: leuchtet nur wenn der PC eingeschaltet ist Active: ein USB Gerät ist verbunden Link: Sende- und Empfangseinheit sind über ein Cat.5 (oder höher)-kabel verbunden USB Port: die entsprechende LED leuchtet wenn ein USB Gerät angeschlossen ist PC1/PC2: zeigt welcher PC aktiv ist [2]
Introduction Merci d avoir choisi l extender USB 2.0 Cat.5 pour 2 PC LINDY. Ce produit est composé d une unité de transmission avec 3 ports USB et d une unité réceptrice avec 7 ports USB, il permet à deux périphériques USB hôtes de transmettre des données jusqu à 100 mètres. Livraison Unités de transmission et de réception Alimentation multi-pays 5V DC 2A pour l unité locale Alimentation multi-pays 5V DC 3.5A pour l unité distante 2 câbles USB Quatre équerres de montage Ce Manuel Caractéristiques Plug and play, ne nécessite pas de pilotes Cet extender USB 2.0 Cat.5 peut être connecté à deux PC, sur l unité de transmission Unité locale avec Hub 3 ports USB 2.0, distante avec Hub 7 ports USB 2.0 Prise en charge USB 2.0 high-speed et USB 1.1 (low-speed, full-speed) jusqu à 100m sur du câble Cat 5e (ou plus haut). Prend en charge tous les types de transferts USB: commande, interruption, blocs et isochrone jusqu à 480Mbits/S Indépendant du système d exploitation Commutation entre deux ordinateurs par bouton poussoir Installation 1. Placez l unité locale de l extender à proximité du(des) ordinateur(s). Installez le câble USB fourni entre l unité locale et le port USB sur l (les) ordinateur(s) hôte(s). Des connecteurs USB type B sont utilisés pour relier l unité locale de l extender à l ordinateur hôte. 2. Connectez l alimentation 5VDC 2A fournie à l unité locale (transmetteur). 3. Placez l unité distante à proximité des périphériques USB et à une distance de jusqu à 100 mètres. 4. Connectez l alimentation 5VDC 3.5A fournie à l unité distante (récepteur). 5. Reliez les unités locale et distante de l extender à l aide d un câble (non inclus) Cat.5 (ou plus haut). Pour commuter entre les deux ordinateurs, veuillez appuyer sur le bouton sur le transmetteur et attendez environ 5 secondes. Indications des LED Power sur le transmetteur: indicateur d alimentation; sur le récepteur : ne s allume que lorsque le PC est démarré Active: un périphérique USB est connecté Link: liaison établie entre transmetteur et récepteur par un câble Cat.5 (ou supérieur) USB ports sur transmetteur/récepteur: la LED correspondante est allumée si un périphérique est connecté PC1/PC2: indique quel PC est actif [3]
Introduzione Vi ringraziamo per aver acquistato l Extender USB 2.0 Cat.5 LINDY per 2 PC. Questo dispositivo è composto da un unità trasmittente dotata di 3 porte USB e un unità ricevente equipaggiata con 7 porte USB e consente a due differenti computer o host USB di connettersi a periferiche USB distanti fino a 100m. Contenuto della confezione Unità Trasmettente/Locale Unità Ricevente/Remota Alimentatore Multi-Country 5V DC 2A per unità locale Alimentatore Multi-Country 5V DC 3.5A per unità remota 2 Cavi USB Quattro staffe di fissaggio Manuale LINDY Caratteristiche Plug and Play reale: nessun driver necessario per l installazione Possibilità di condivisione fra due PC di questo extender USB 2.0 Cat.5 Unità Locale con hub USB 2.0 a 3 Porte, unità Remota con hub USB 2.0 a 7 Porte Estende la connessione USB 2.0 high-speed e USB 1.1 (low-speed, full-speed) fino a 100m di distanza su cavo Cat 5e (o superiore). Supporta tutti i tipi di periferiche USB: Control, Interrupt, Bulk e Isocrone fino a 480Mbps Funziona con tutti i maggiori sistemi operativi che supportano lo standard USB Selezione del computer in uso tramite pulsante dedicato Installazione 1. Posizionate l unità locale vicino al (o ai) Computer. Collegate con il cavo fornito in dotazione la porta USB dell unità locale con una porta USB del computer. Per la connessione dei computer sono utilizzati comuni cavi USB Tipo A/B. 2. Collegato l alimentatore da 5VDC 2A all unità locale appena installata. 3. Posizionate l unità remota vicino al luogo dove volete installare i dispositivi USB da controllare. 4. Collegate l alimentatore da 5VDC 3.5A all unità remota. 5. Collegate le dune unità locale e remota utilizzando un cavo (non incluso!) Cat.5 (o superiore). Per spostare il controllo da un PC all altro utilizzate il pulsante presente sull unità locale e attendere circa 5 secondi. Indicatori LED LED Power sul trasmettitore: alimentazione attiva; sul ricevitore: si illumina solo a PC acceso Active: dispositivo USB connesso Link: trasmettitore e ricevitore sono connessi correttamente con cavo Cat.5 o sup. Porte USB sul trasmettitore e ricevitore: I rispettivi LED si accendono quando un dispositivo USB e connesso PC1/PC2: indica quale PC è attivo [4]
CE/FCC CE Certification This equipment complies with the requirements relating to Electromagnetic Compatibility Standards EN55022/EN55024 and the further standards cited therein. It must be used with shielded cables only. It has been manufactured under the scope of RoHS compliance. CE Konformitätserklärung Dieses Produkt entspricht den einschlägigen EMV Richtlinien der EU für IT-Equipment und darf nur zusammen mit abgeschirmten Kabeln verwendet werden. Diese Geräte wurden unter Berücksichtigung der RoHS Vorgaben hergestellt. Die formelle Konformitätserklärung können wir Ihnen auf Anforderung zur Verfügung stellen FCC Certification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. You are cautioned that changes or modification not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation LINDY Herstellergarantie Hinweis für Kunden in Deutschland LINDY gewährt für dieses Produkt über die gesetzliche Regelung in Deutschland hinaus eine zweijährige Herstellergarantie ab Kaufdatum. Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den AGBs. Hersteller / Manufacturers (EU): LINDY Electronics Ltd. LINDY-Elektronik GmbH Sadler Forster Way Markircher Str. 20 Teesside Industrial Estate, Thornaby 68229 Mannheim Stockton-on-Tees, TS17 9JY GERMANY United Kingdom Email: info@lindy.de postmaster@lindy.co.uk T: +49 (0)621 470050 T: +44 (0)1642 754000
Recycling Information WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products United Kingdom In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process. Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency. Germany / Deutschland Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das Recycling von Elektro- und Elektronikprodukten geschaffen. Diese wurden von der Bundesregierung im Elektro- und Elektronikgerätegesetz ElektroG in deutsches Recht umgesetzt. Dieses Gesetz verbietet vom 24.März 2006 an das Entsorgen von, auch alten, Elektro- und Elektronikgeräten über die Hausmülltonne! Diese Geräte müssen den lokalen Sammelsystemen bzw. örtlichen Sammelstellen zugeführt werden! Dort werden sie kostenlos entgegen genommen. Die Kosten für den weiteren Recyclingprozess übernimmt die Gesamtheit der Gerätehersteller. France En 2006, l'union Européenne a introduit la nouvelle réglementation (DEEE) pour le recyclage de tout équipement électrique et électronique. Chaque Etat membre de l Union Européenne a mis en application la nouvelle réglementation DEEE de manières légèrement différentes. Veuillez suivre le décret d application correspondant à l élimination des déchets électriques ou électroniques de votre pays. Italy Nel 2006 l unione europea ha introdotto regolamentazioni (WEEE) per la raccolta e il riciclo di apparecchi elettrici ed elettronici. Non è più consentito semplicemente gettare queste apparecchiature, devono essere riciclate. Ogni stato membro dell EU ha tramutato le direttive WEEE in leggi statali in varie misure. Fare riferimento alle leggi del proprio Stato quando si dispone di un apparecchio elettrico o elettronico. Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato. LINDY No. 42695 Tested to Comply with FCC Standards For Home and Office Use! 2 nd Edition May 2015 www.lindy.com [6]