Beleuchteter Spiegel 00099 00099 00099
0 Artikel Artikelnummer 00099 00099 00099 Maße 80x60 cm 0x80 cm 40x70 cm Teile im Lieferumfang Lieferumfang A B C Spiegel Schrauben Dübel Benötigtes Werkzeug (nicht im Lieferumfang enthalten 4
0 4 Montage. Messen Sie den Abstand zwischen den Montagelöchern des Spiegels (A) ab. Zeichnen Sie mit Hilfe eines Maßbands oder Zollstocks zwei Bohrungen an der Wand an.. Bohren Sie die Löcher an den Markierungen.. Stecken Sie einen Dübel (C) in jedes Bohrloch in der Wand. Nehmen Sie einen weichen Hammer zur Hilfe, falls nötig. C 4. Nun die Schrauben in die Löcher mit den Dübeln schrauben. Lassen Sie die Schrauben 6-8 mm aus der Wand herausstehen. B
Das Stromkabel anschließen. Führen Sie das Kabel in die Löcher. sensor switch Sensorschalter Den Spiegel an den herausstehenden Schrauben aufhängen wie im Bild unten. sensor Sensorschalter switch 4
Hinweise zur Entsorgung Befindet sich die linke Abbildung (durchgestrichene Mülltonne auf Rädern) auf dem Produkt, gilt die Europäische Richtlinie 0/9/EU. Diese Produkte dürfen nicht mit dem normalen Hausmüll entsorgt werden. Informieren Sie sich über die örtlichen Regelungen zur getrennten Sammlung elektrischer und elektronischer Gerätschaften. Richten Sie sich nach den örtlichen Regelungen und entsorgen Sie Altgeräte nicht über den Hausmüll. Durch die regelkonforme Entsorgung der Altgeräte werden Umwelt und die Gesundheit ihrer Mitmenschen vor möglichen negativen Konsequenzen geschützt. Materialrecycling hilft, den Verbrauch von Rohstoffen zu verringern. Konformitätserklärung Hersteller: Chal-Tec GmbH, Wallstraße 6, 079 Berlin Dieses Produkt entspricht den folgenden Europäischen Richtlinien: 04/0/EU (EMV) 04/5/EU (LVD) 0/65/EU (RoHS) 5
Illuminated Mirror 00099 00099 00099
0 Item Item number 00099 00099 00099 Measurements 80x60 cm 0x80 cm 40x70 cm Parts included Scope of Delivery A B C mirror screws dowels Tools needed (not included) 4 7
0 4 Montage. Measure the distance between hangers of the mirror (A). Mark the places for the two drill holes using a tape measure or a folding rule. Drill two level holes into the wall using the marks.. Using a soft mallet, if necessary, lightly fit the dowels (C) into the drilled holes. C 4. Insert the screws (B)into the anchors, leaving 6-8mm of the screw exposed. B 8
Connect the wire: Press down the connextion,put the wire into the holes. sensor switch Install the mirror (A) as shown. sensor switch 9
Disposal Considerations According to the European waste regulation 00/96/EC this symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council or your household waste disposal service. Declaration of Conformity Producer: Chal-Tec GmbH, Wallstraße 6, 079 Berlin, Germany This product is conform to the following European Directives: 04/0/EU (EMC) 04/5/EU (LVD) 0/65/EU (RoHS) 0