Data sheet C6 A modul 2 port 180 M UP0

Transkript

1 Illustrations Dimensional drawing Page 1/7 See enlarged drawings at the end of document Product specification termination unit with C6 A modul 180 certified to GHMT Cat.6 A re-embedded PVP component testing for Cat.6 A to ISO/IEC Ed.2.2: , DIN EN : , TIA/EIA-568-C.2 ( ) and IEC Ed.1 (12/2008), certified to GHMT compliance with class E A up to 500 MHz to ISO/IEC Ed.2.2: , DIN EN : tested: components up to 600 MHz, link up to 800 MHz suitable for 10 GBit Ethernet (IEEE 802.3an), Remote Powering (PoE, PoE plus and UPoE) and HDBaseT connection of data lines AWG 26/1 to 22/1 (solid wire) and AWG 26/7 to 22/7 (stranded wire) to insulation displacement connectors (IDC) module plug direction 45 downwards strain relief snapped on to stuffer cap compatible with "design" central units of switch lines (note: 3 port central units at present only available from JUNG) not suitable for mounting in standard flush-mounted or cavity wall casings! variants: 1 port, 2 ports, 3 ports

2 Page 2/7 General Data Fields of application Design Mounting style Shielding Transmission technology Wiring Color Dimensions Dimension (L x W x H) Dimension (L x W x H) Modularity Office Wall outlet UP0 shielded Copper T568A, T568B metallike x x mm 1.30 x 2.75 x 2.75 in. Transmission characteristics Category (ISO) Class (ISO/IEC) Category (TIA) Remote Powering PoE PoE plus UPoE HDBaseT Transmission rate up to 10 GBit 6 A E A 6A IEEE 802.3af IEEE 802.3at IEEE 802.3an Connections/interfaces Connector technology interface 1 Connector technology interface 2 Number of ports interface 2 2 Number of ports interface 2 equipped 2 Number of positions/contacts interface 1 2 x 8 Number of positions/contacts interface 2 IDC-connection RJ45-jack 2 x 8P/8C

3 Page 3/7 Connections/interfaces Termination data, solid wire (min. - max.) Conductor cross section, solid wire AWG 26/1-22/1 Conductor cross section, solid wire Conductor diameter, solid wire (bare copper) Conductor diameter, solid wire (bare copper) mm² mm in. Termination data, stranded wire (min. - max.) Conductor cross section, stranded wire AWG 26/7-22/7 Conductor cross section, stranded wire Conductor diameter, stranded wire (bare copper) Conductor diameter, stranded wire (bare copper) Module plug-in direction Cable access/outlet mm² mm in. 45 downwards Electrical characteristics Current carrying capacity Rated voltage Contact resistance Through resistance Insulation resistance Dielectric strength conductor-conductor (secondary) max. 1 A max. 50 V max. 20 mohm max. 200 mohm min. 500 MOhm max V DC Mechanical characteristics Cut-out Insertion and withdrawal force Position/mounting of latch - standard installation position Strain relief Modul max. 30 N top latching clip Materials and material properties Material - Housing Material - Supporting frame Material - Module support Material - Contact Material - Contact finish Material - Shield Spring steel Au (gold)

4 Page 4/7 Materials and material properties Material - Stuffer cap Material - Strain relief PA 6.6 UL94 V0 PA 6.6 UL94 V0 Environmental conditions Temperature (min. - max.) Temperature - Storage C C Temperature - Storage F F Temperature - Operating C C Temperature - Operating F F Particulate ingress Liquid ingress/immersion Rapid change of temperature Electromagnetic measurement E 2 IP2X IPX0-40 C / -40 F C / 158 F / 25 cycles t=30 min Certifications GHMT Component GHMT PVP CE RoHS compliant compliant The product meets the following standards Generic cabling systems General requirements ISO/IEC Ed.2.2: DIN EN : TIA/EIA 568-C Office buildings ISO/IEC Ed.2.2: DIN EN : TIA/EIA 568-C Living units ISO/IEC DIN EN : TIA/EIA 570-B Connectors for electronic equipment Free and fixed connectors DIN EN : Connectors for electronic equipment - Tests and measurements Test schedule for connectors DIN-EN : , Pg. UEL1 Endurance tests IEC : Degrees of Protection Provided by Enclosures IEC 60529

5 Page 5/7 The product meets the following standards Interference proof Immunity for industrial environments DIN EN : Classifications ETIM 5.0 EC Packing details Type of packaging Packaging unit - Weight (gram) Packaging unit - Weight (pound) Packaging dimension (W x H x D) Packaging dimension (W x H x D) 10 pc(s) / box g 2.40 lb x x mm 9.25 x 6.50 x 5.31 in.

6 Accessories Page 6/7 Designation I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Montagehalter für Anschlussdosen I Cover plates for E-DAT modul wall outlets I FKH-I FNI-I FTE-I ADTK-I ADTSA-I I I Cover plates for E-DAT modul wall outlets Mounting bracket FR for Kleinhuis Mounting bracket FR for Niedax Mounting bracket FR for Tehalit Mounting bracket ADTK for OBO Mounting bracket ADTSA for OBO Surface mount frame 43x85x85 pearl white Surface mount frame 43x85x85 pure white

7 Powered by TCPDF ( Data sheet Illustrations Dimensional drawing Page 7/7