Präzisionswerkzeuge MAIER GmbH HEAD-Master R VHM Soli Carbie Gewinefräsen Threa En milling
Anwenung VHM-Bohrgewine-Fräser mit / Instruction for Soli carbie-drill-threa En mill witch chamfer 1 1/2 1/3 1/2 1.- Heranführen an as Werkstück. 2.- Arbeitsgang es Bohr-Gewine Fräsers Bohren un Senken 3.- Rücklauf zur Regulierung er Gewinelänge 4.- 180º Einrehung, Regulierung er Gewinefräsabmessung 5.- 360º Drehung zum Gewinefräsen, Interolation mit er Gewinesteigung um ie Fräserachse 6.- 180º Ausrehung zum Rücklauf es Fräsers zur Bohrungsachse 7.- Rücklauf es Bohr-Gewine Fräsers zur Ausgangsosition Einsatzgebiete in kurzsanenen Materialien: Grauguss, legierter Grauguss, Messing un kurzsanene Bronze, Aluminium, Aluminiumlegierungen. 1.- Positioning the Threa mill 2.- Drilling an countersinking 3.- Backing off for threa length ajustment. 4.- Run-in loo 180, ajust to the trea milling size 5.- Turn 360 for threa milling, interolation with the threa itch, aroun the mill axis 6.- Run-out loo 180 to return the mill to the hole axis 7.- Retracting the threa mill to the start osition. The alication range is in short chiing materials: Grey cast iron, Alloyes grey cas iron, Brass an short chiing Bronze, Aluminium, Aluminium alloys. 02
1.5 x D - VHM-Bohrgewine-Fräser mit 1.5 x D - Soli carbie-drill-threa En mill with chamfer M Ø Ø Ø 2 l3 e Z 1200.025... 1200.026... 1200.030... e 2 M3 0,5 6 2,5 3,4 48 5,4 5,8 0,50 2 283,00 283,00 297,00 M3-IK 0,5 6 2,5 3,4 48 5,4 5,8 0,50 2 311,00 311,00 327,00 M4 0,7 6 3,3 4,5 48 6,8 7,3 0,70 2 283,00 283,00 297,00 M4-IK 0,7 6 3,3 4,5 48 6,8 7,3 0,70 2 311,00 311,00 327,00 M5 0,8 6 4,2 5,5 53 8,5 9,2 0,80 2 278,00 278,00 292,00 M5-IK 0,8 6 4,2 5,5 53 8,5 9,2 0,80 2 306,00 306,00 321,00 M6 1,0 8 5,0 6,6 59 10,2 11,5 1,00 2 281,00 281,00 295,00 M6-IK 1,0 8 5,0 6,6 59 10,2 11,5 1,00 2 309,00 309,00 325,00 M8 1,25 10 6,75 9,0 70 13,4 14,4 1,25 2 331,00 331,00 348,00 M8-IK 1,25 10 6,75 9,0 70 13,4 14,4 1,25 2 364,00 364,00 382,00 M10 1,5 12 8,5 11,0 75 17,6 18,9 1,50 2 382,00 382,00 401,00 M10-IK 1,5 12 8,5 11,0 75 17,6 18,9 1,50 2 419,00 419,00 440,00 M12 1,75 14 10,25 13,5 84 20,2 21,8 1,50 2 493,00 493,00 518,00 M12-IK 1,75 14 10,25 13,5 84 20,2 21,8 1,50 2 536,00 536,00 563,00 M14 2,0 16 12,0 15,5 94 23,0 24,8 1,50 2 625,00 625,00 656,00 M14-IK 2,0 16 12,0 15,5 94 23,0 24,8 1,50 2 678,00 678,00 712,00 M16 2,0 18 14,0 17,5 94 27,0 29,1 1,50 2 767,00 767,00 805,00 M16-IK 2,0 18 14,0 17,5 94 27,0 29,1 1,50 2 834,00 834,00 875,00 Bestellbeisiel / Orerexamle: 1200.025.M3-HA 2,0 x D - VHM-Bohrgewine-Fräser mit 2,0 x D - Soli carbie-drill-threa En mill with chamfer l3 M Ø Ø Ø 2 l3 e Z 1201.025... 1201.026... 1201.030... 2 = max. Senkurchmesser max. iameter = Programmierwert für Senkung Programming value for chamfer e = Einstichbreite / uncture-wie M3 0,5 6 2,5 3,4 49 6,9 7,3 0,50 2 283,00 283,00 297,00 M3-IK 0,5 6 2,5 3,4 49 6,9 7,3 0,50 2 311,00 311,00 327,00 M4 0,7 6 3,3 4,5 49 8,9 9,4 0,70 2 283,00 283,00 297,00 M4-IK 0,7 6 3,3 4,5 49 8,9 9,4 0,70 2 311,00 311,00 327,00 M5 0,8 6 4,2 5,5 55 10,9 11,6 0,80 2 278,00 278,00 292,00 M5-IK 0,8 6 4,2 5,5 55 10,9 11,6 0,80 2 306,00 306,00 321,00 M6 1,0 8 5,0 6,6 62 13,7 14,5 1,00 2 281,00 281,00 295,00 M6-IK 1,0 8 5,0 6,6 62 13,7 14,5 1,00 2 309,00 309,00 325,00 M8 1,25 10 6,75 9,0 74 17,2 18,2 1,25 2 331,00 331,00 348,00 M8-IK 1,25 10 6,75 9,0 74 17,2 18,2 1,25 2 364,00 364,00 382,00 M10 1,5 12 8,5 11,0 79 22,1 23,4 1,50 2 382,00 382,00 401,00 M10-IK 1,5 12 8,5 11,0 79 22,1 23,4 1,50 2 419,00 419,00 440,00 M12 1,75 14 10,25 13,5 89 25,5 27,1 1,50 2 493,00 493,00 518,00 M12-IK 1,75 14 10,25 13,5 89 25,5 27,1 1,50 2 536,00 536,00 563,00 M14 2,0 16 12,0 15,5 102 31,0 32,8 1,50 2 625,00 625,00 656,00 M14-IK 2,0 16 12,0 15,5 102 31,0 32,8 1,50 2 678,00 678,00 712,00 M16 2,0 18 14,0 17,5 102 35,0 37,1 1,50 2 767,00 767,00 805,00 M16-IK 2,0 18 14,0 17,5 102 35,0 37,1 1,50 2 834,00 834,00 875,00 Bestellbeisiel / Orerexamle: 1201.025.M3-HA 03
Anwenung VHM-Gewine-Fräser mit / Instruction for Soli carbie-threa En mill witch chamfer 1/2 1 1/3 1/2 1.- Heranführen an ie Vorbohrung. 2.- Arbeitsgang es Gewinefräsers Senken 3.- Rücklauf zur Regulierung er Gewinelänge 4.- 180º Einrehung, Regulierung er Gewinefräsabmessung 5.- 360º Drehung zum Gewinefräsen, Interolation mit er Gewinesteigung um ie Fräserachse 6.- 180º Ausrehung zum Rücklauf es Fräsers zur Bohrungsachse 7.- Rücklauf es Gewinefräsers zur Ausgangsosition Einsatzgebiete in kurzsanenen Materialien: Grauguss, legierter Grauguss, Messing un kurzsanene Bronze, Aluminium, Aluminiumlegierungen, nierig legierte Stähle, legierte Stähle bis 1.400N/mm², rostfreie Stähle, Titatnlegierungen 1.- Positioning the Threa mill 2.- Avancing mill an countersinking 3.- Backing off for threa length ajustment. 4.- Run-in loo 180, ajust to the trea milling size 5.- Turn 360 for threa milling, interolation with the threa itch, aroun the mill axis 6.- Run-out loo 180 to return the mill to the hole axis 7.- Retracting the threa mill to the start osition. The alication range is in short chiing materials: Grey cast iron, Alloyes grey cas iron, Brass an short chiing Bronze, Aluminium, Aluminium alloys, Low alloye steels, Alloye steels u to 1.400 N/mm², Stainless steels, Titanium alloys. 04
2.0 x D - VHM-Einzahn-Gewinefräser 2.0 x D - Soli carbie single tooth threa milling cutters M Ø Ø Z 1202.025... 1202.026... 1202.030... M1 0,25 3 0,74 32 3,0 4 128,00 128,00 135,00 M1,2 0,25 3 0,90 32 3,5 4 128,00 128,00 135,00 M1,4 0,30 3 1,00 32 3,5 4 119,00 119,00 126,00 M1,6 0,35 3 1,20 32 4,0 4 119,00 119,00 126,00 M1,8 0,35 3 1,35 32 4,0 4 112,00 112,00 117,00 M2 0,40 3 1,50 32 4,0 4 112,00 112,00 117,00 M2,5 0,45 3 1,90 32 6,0 5 112,00 112,00 117,00 M3 0,50 3 2,40 32 6,0 5 112,00 112,00 117,00 M3,5 0,60 3 2,80 32 6,0 6 112,00 112,00 117,00 M4 0,70 5 3,20 40 8,0 6 129,00 129,00 136,00 M5 0,80 5 4,10 40 9,0 6 129,00 129,00 136,00 M6 1,00 5 4,90 40 9,0 6 129,00 129,00 136,00 Bestellbeisiel / Orerexamle: 1202.025.M1-HA Achtung: Kernloch (un ggf. Ansenkung) muss bereits vorhanen sein Attention: core hole (an ossibly countersink) must alreay exist 3.0 x D - VHM-Einzahn-Gewinefräser m.ik 3.0 x D - Soli carbie single tooth threa milling cutters with IK M Ø Ø Z 1203.025... 1203.026... 1203.030... M1 0,25 3 0,70 39 3,0 1 138,00 138,00 145,00 M1,6 0,35 3 1,18 39 4,8 2 133,00 133,00 141,00 M2 0,40 3 1,52 39 6,0 3 123,00 123,00 130,00 M2,5 0,45 3 1,96 39 7,5 3 123,00 123,00 130,00 M3 0,50 3 2,40 41 9,0 3 123,00 123,00 130,00 M4 0,70 4 3,15 44 12,0 3 151,00 151,00 159,00 M5 0,80 6 4,04 56 15,0 4 156,00 156,00 165,00 M6 1,00 6 4,80 59 18,0 4 156,00 156,00 165,00 M8-IK 1,25 8 6,50 65 24,0 5 189,00 189,00 198,00 M10-IK 1,50 10 8,20 77 31,5 5 222,00 222,00 234,00 M12-IK 1,75 10 9,90 82 37,7 5 222,00 222,00 234,00 M14-IK 2,00 12 11,60 94 42,0 5 329,00 329,00 346,00 M16-IK 2,00 14 13,60 100 48,0 5 372,00 372,00 391,00 Bestellbeisiel / Orerexamle: 1203.025.M1-HA Achtung: Kernloch (un ggf. Ansenkung) muss bereits vorhanen sein Attention: core hole (an ossibly countersink) must alreay exist 05
2.0 x D VHM-Gewinefräser m.ik 2.0 x D Soli carbie threa milling cutters with IK M Ø Ø Z 1204.025... 1204.026... 1204.030... M3 0,50 4 2,40 42 6,2 3 180,00 180,00 190,00 M4-IK 0,70 6 3,15 55 8,7 3 134,00 134,00 141,00 M5-IK 0,80 6 4,00 55 10,8 3 136,00 136,00 143,00 M6-IK 1,00 6 4,80 55 12,5 3 161,00 161,00 169,00 M8-IK 1,25 6 6,00 63 16,8 3 191,00 191,00 201,00 M10-IK 1,50 8 8,00 70 20,2 3 215,00 215,00 226,00 M12-IK 1,75 10 9,90 80 25,3 4 268,00 268,00 282,00 M14-IK 2,00 12 11,60 90 29,0 4 295,00 295,00 311,00 M16-IK 2,00 12 12,00 90 32,9 4 336,00 336,00 354,00 M20-IK 2,50 14 14,00 90 41,2 4 391,00 391,00 411,00 M24-IK 3,00 16 16,00 90 37,3 5 477,00 477,00 502,00 Bestellbeisiel / Orerexamle: 1204.025.M3-HA 1.5 x D VHM-Gewinefräser mit 1.5 x D Soli carbie-drill-threa En mill with chamfer M Ø Ø Ø 2 Z 1205.025... 1205.026... 1205.030... 2 M3 0,50 6 2,44 3,3 40 4,66 3 207,00 207,00 218,00 M4 0,70 6 3,14 4,5 47 6,50 4 210,00 210,00 221,00 M5 0,80 6 3,95 5,5 52 8,20 4 219,00 219,00 230,00 M6 1,00 8 4,68 6,6 59 10,20 4 239,00 239,00 252,00 M8 1,25 10 6,22 9,0 70 14,10 4 266,00 266,00 280,00 M10 1,50 12 7,79 11,0 74 16,90 5 266,00 266,00 280,00 M12 1,75 14 9,37 13,5 82 19,70 5 290,00 290,00 305,00 M14 2,00 16 10,92 15,5 96 24,50 5 380,00 380,00 401,00 M16 2,00 18 12,82 17,5 94 26,50 5 403,00 403,00 424,00 Bestellbeisiel / Orerexamle: 1205.025.M3-HA 2 = max. Senkurchmesser / max. iameter = Programmierwert für Senkung / Programming value for chamfer 06
1.5 x D VHM-Gewinefräser mit un m.ik 1.5 x D Soli carbie-drill-threa En mill with chamfer an IK M Ø Ø Ø 2 Z 1206.025... 1206.026... 1206.030... M4 0,70 6 3,14 4,5 47 6,5 3 159,00 159,00 167,00 M6-IK 1,00 8 4,68 6,6 59 10,2 3 189,00 189,00 199,00 M8-IK 1,25 10 6,22 9,0 70 14,1 3 229,00 229,00 241,00 M10-IK 1,50 12 7,79 11,0 74 16,9 3 263,00 263,00 277,00 M12-IK 1,75 14 9,37 13,5 82 19,7 3 330,00 330,00 348,00 M16-IK 2,00 18 12,82 17,5 94 26,5 4 479,00 479,00 505,00 M20-IK 2,50 25 15,82 24,0 117 35,6 4 567,00 567,00 597,00 Bestellbeisiel / Orerexamle: 1206.025.M4-HA 2.0 x D VHM-Gewinefräser mit un m.ik 2.0 x D Soli carbie-drill-threa En mill with chamfer an IK M Ø Ø Ø 2 Z 1207.025... 1207.026... 1207.030... 2 M4 0,70 6 3,14 4,5 49 8,6 3 159,00 159,00 167,00 M5 0,80 6 3,95 5,5 55 10,6 3 163,00 163,00 172,00 M6-IK 1,00 8 4,68 6,6 62 13,2 3 189,00 189,00 199,00 M8-IK 1,25 10 6,22 9,0 74 17,8 3 229,00 229,00 241,00 M10-IK 1,50 12 7,79 11,0 79 21,4 3 263,00 263,00 277,00 M12-IK 1,75 14 9,37 13,5 89 26,7 3 330,00 330,00 348,00 M16-IK 2,00 18 12,82 17,5 102 34,5 4 479,00 479,00 505,00 M20-IK 2,50 25 15,82 24,0 127 45,6 4 567,00 567,00 597,00 Bestellbeisiel / Orerexamle: 1207.025.M4-HA 2.5 x D VHM-Gewinefräser mit un m.ik 2.5 x D Soli carbie-drill-threa En mill with chamfer an IK M Ø Ø Ø 2 Z 1208.025... 1208.026... 1208.030... M5 0,80 6 3,95 5,5 55 13,0 3 170,00 170,00 179,00 M6-IK 1,00 8 4,68 6,6 62 16,2 3 199,00 199,00 210,00 M8-IK 1,25 10 6,22 9,0 74 21,6 3 240,00 240,00 253,00 M10-IK 1,50 12 7,79 11,0 79 27,4 3 282,00 282,00 297,00 M12-IK 1,75 14 9,37 13,5 89 31,9 3 350,00 350,00 369,00 Bestellbeisiel / Orerexamle: 1208.025.M5-HA 2 = max. Senkurchmesser / max. iameter = Programmierwert für Senkung / Programming value for chamfer 07
2.0 x D VHM-Feingewinefräser m.ik 2.0 x D Soli carbie fine-threa milling cutters with IK M Ø Ø Z 1209.025... 1209.026... 1209.030... M2,5 x 0,35 0,35 3 2,06 39 5,3 3 227,00 227,00 239,00 M3 x 0,35 0,35 3 2,55 39 6,2 3 227,00 227,00 239,00 M4 x 0,5-IK 0,50 6 3,35 55 8,2 3 227,00 227,00 239,00 M5 x 0,5-IK 0,50 6 4,30 55 10,2 3 229,00 229,00 241,00 M6 x 0,75-IK 0,75 6 5,00 55 12,4 3 205,00 205,00 216,00 M8 x 0,75-IK 0,75 6 6,00 63 16,8 3 207,00 207,00 218,00 M8 x 1,0-IK 1,00 6 6,00 63 16,4 3 202,00 202,00 213,00 M10 x 1,0-IK 1,00 8 8,00 70 20,5 3 240,00 240,00 253,00 M12 x 1,0-IK 1,00 10 10,00 80 24,5 4 290,00 290,00 305,00 M12 x 1,5-IK 1,50 10 10,00 80 24,7 4 292,00 292,00 308,00 M14 x 1,5-IK 1,50 10 10,00 80 29,2 4 305,00 305,00 321,00 M16 x 1,5-IK 1,50 12 12,00 90 32,2 4 363,00 363,00 382,00 M18 x 1,5-IK 1,50 14 14,00 90 36,7 4 418,00 418,00 440,00 M20 x 1,5-IK 1,50 14 14,00 90 41,2 4 435,00 435,00 458,00 M22 x 1,5-IK 1,50 14 14,00 95 44,2 4 449,00 449,00 473,00 M24 x 1,5-IK 1,50 16 16,00 90 36,7 5 477,00 477,00 502,00 Bestellbeisiel / Orerexamle: 1209.025.M2,5x0,35-HA 2 1.5 x D VHM-Feingewinefräser mit un m.ik 1.5 x D Soli carbie fine-threa milling cutters with chamfer an IK M Ø Ø Ø 2 Z 1210.025... 1210.026... 1210.030... M8 x 1,0 1,00 10 6,22 9,0 70 13,4 3 243,00 243,00 256,00 M10 x 1,0 1,00 12 7,79 11,0 74 16,5 3 290,00 290,00 305,00 M12 x 1,5 1,50 14 9,37 13,5 82 20,0 3 356,00 356,00 375,00 Bestellbeisiel / Orerexamle: 1210.025.M8x1,0-HA 2 = max. Senkurchmesser / max. iameter = Programmierwert für Senkung / Programming value for chamfer 08
2 2.0 x D VHM-Feingewinefräser mit m.ik 2.0 x D Soli carbie fine-threa milling cutters with chamfer an IK M Ø Ø Ø 2 Z 1211.025... 1211.026... 1211.030... M8 x 1,0 1,00 10 6,22 9,0 74 17,4 3 243,00 243,00 256,00 M10 x 1,0 1,00 12 7,79 11,0 79 21,5 3 290,00 290,00 305,00 M12 x 1,5 1,50 14 9,37 13,5 88 26,0 3 356,00 356,00 375,00 M16 x 1,5 1,50 18 12,82 33,6 102 33,6 4 505,00 505,00 531,00 Bestellbeisiel / Orerexamle: 1211.025.M8x1,0-HA 2.0 x D VHM-Zoll-Gewinefräser m.ik 2.0 x D Soli carbie-inch-threa en mill with IK Zoll Gänge ro Zoll Ø Ø Z 1212.025... 1212.026... 1212.030... 2 G1/16 28 8 6,36 62 16,2 3 242,00 242,00 255,00 G1/8 28 8 8,00 70 20,4 3 242,00 242,00 255,00 G1/4 19 12 11,00 90 27,3 4 295,00 295,00 311,00 G3/8 19 12 12,00 90 34,0 4 376,00 376,00 396,00 G1/2 14 14 14,00 95 42,6 4 439,00 439,00 462,00 G3/4 14 16 16,00 90 34,0 5 561,00 561,00 591,00 G1 11 16 16,00 90 35,8 5 625,00 625,00 658,00 Bestellbeisiel / Orerexamle: 1212.025.G1/16-HA Achtung: Für zylinrische Rohrgewine DIN-ISO 228/1 (nicht im Gewine ichtene Verbinungen) Attention: For cylinrical ie threas DIN-ISO 228/1 (not threa-sealing comouns) 2.0 x D VHM-Zoll-Gewinefräser mit m.ik 2.0 x D Soli carbie-inch-threa en mill with chamfer an IK Zoll Gänge ro Zoll Ø Ø Ø 2 Z 1213.025... 1213.026... 1213.030... G1/8 28 12 7,79 11,0 79 21,3 3 291,00 291,00 306,00 G1/4 19 16 10,92 15,5 100 28,5 4 394,00 394,00 415,00 Bestellbeisiel / Orerexamle: 1213.025.G1/8-HA 2 = max. Senkurchmesser / max. iameter = Programmierwert für Senkung / Programming value for chamfer Achtung: Für zylinrische Rohrgewine DIN-ISO 228/1 (nicht im Gewine ichtene Verbinungen) Attention: For cylinrical ie threas DIN-ISO 228/1 (not threa-sealing comouns) 09
2.0 x D VHM-UNC-Gewinefräser mit m.ik 2.0 x D Soli carbie-unc-threa en mill with chamfer an IK UNC Gänge ro Zoll Ø Ø Ø 2 Z 1214.025... 1214.026... 1214.030... 1/4-20 20 8 4,70 6,6 62 15,4 3 232,00 232,00 244,00 5/16-18 18 10 6,22 8,2 74 17,1 3 266,00 266,00 280,00 3/8-16 16 12 7,34 9,8 79 20,9 3 310,00 310,00 327,00 7/16-14 14 14 8,57 11,4 89 23,9 3 469,00 469,00 494,00 1/2-13 13 14 9,38 13,0 89 27,8 3 430,00 430,00 453,00 5/8-11 11 18 12,50 16,2 102 35,0 4 591,00 591,00 622,00 3/4-10 10 20 15,21 19,3 108 41,1 4 655,00 655,00 690,00 Bestellbeisiel / Orerexamle: 1214.025.UNC-1/4-20-HA Achtung: Für UNC Einheits-Grobgewine ASME-B1.1 Attention: For UNC unit coarse threa ASME B1.1 2 2.0 x D VHM-UNF-Gewinefräser mit m.ik 2.0 x D Soli carbie-unf-threa en mill with chamfer an IK UNF Gänge ro Zoll Ø Ø Ø 2 Z 1215.025... 1215.026... 1215.030... 1/4-28 28 8 4,70 6,6 62 14,8 3 261,00 261,00 275,00 5/16-24 24 10 6,22 8,2 74 17,2 3 295,00 295,00 311,00 3/8-24 24 12 7,79 9,8 79 20,4 3 340,00 340,00 358,00 7/16-20 20 14 9,32 11,4 88 23,1 3 493,00 493,00 519,00 1/2-20 20 14 9,38 13,0 89 27,4 3 454,00 454,00 478,00 9/16-18 18 16 10,92 14,6 102 30,3 4 520,00 520,00 548,00 3/4-16 16 20 16,70 19,3 108 40,1 4 690,00 690,00 727,00 Bestellbeisiel / Orerexamle: 1215.025.UNF-1/4-28-HA Achtung: Für UNF Einheits-Grobgewine ASME-B1.1 Attention: For UNF unit coarse threa ASME B1.1 VHM-NPT-Gewinefräser mit m.ik Soli carbie-npt-threa en mill with chamfer an IK NPT Gänge ro Zoll Ø Ø Ø 2 Z 1216.025... 1216.026... 1216.030... 10 1/8-27 27 12 8,16 11,1 70 10,4 3 317,00 317,00 334,00 Bestellbeisiel / Orerexamle: 1216.025.NPT-1/8-27 2 = max. Senkurchmesser / max. iameter = Programmierwert für Senkung / Programming value for chamfer Achtung: Für kegliges Rohrgewine (NPT), nach ANSI B1.20.1, für Gewine mit Dichtmittel Attention: For taere ie threa (NPT) to ANSI B1.20.1 for threa sealant
Schnittatenemfehlungen / Cutting ata recommenation P M K N S Nierig- & Mittel-Legierter Kohlenstoffstahl Low- & Mile alloye carbonsteel Hoch-Legierter Kohlenstoffstahl High alloye carbonsteel Legierter Stahl, Vergütungsstahl alloye steel, remuneration steel Rostfreier Stahl, ferritisch stainless steel, ferritic Rostfreier Stahl, austenitisch stainless steel, austenitic Grauguss Gray cast iron Shäroguss Sheroial cast iron Nichteisenmetalle, Aluminium Non-ferrous metals, aluminum Bronze, Messing, Kunststoff Bronze, brass, lastic Nickellegierung, Titanlegierung Nickel alloy, Titanium alloy Vc (m/min) ø8 fz ø10 fz ø12 fz ø14 fz ø16 fz ø20 fz 100-250 0,06 0,07 0,07 0,08 0,10 0,12 110-180 0,05 0,05 0,06 0,07 0,09 0,10 90-160 0,03 0,04 0,04 0,05 0,06 0,07 60-160 0,04 0,04 0,05 0,06 0,06 0,08 60-120 0,04 0,04 0,04 0,05 0,06 0,07 130-170 0,03 0,04 0,04 0,05 0,06 0,07 70-150 0,06 0,07 0,07 0,08 0010 0,12 150-350 0,06 0,07 0,07 0,08 0,10 0,12 100-400 0,08 0,09 0,10 0,11 0,13 0,15 20-80 0,02 0,02 0,02 0,03 0,03 0,03 Die angegebenen Schnittwerte sin reine Emfehlungswerte The above ata are aroximate. 11
Maier GmbH Präzisionswerkzeuge Dorfstraße 14 94330 Salching Tel.: +49 (0) 9426 / 80 26 50 Fax: +49 (0) 9426 / 80 26 51 Mail: info@maier-tools.e www.maier-tools.e VHM Gewinefräsen 2015