ORFS Rohrverschraubungen mit stirnseitiger O-Ring Abdichtung ORFS pipe unions with O-ring seal on the end face ORFS-Rohrverschraubungen (O-Lok), entsprechen den jeweiligen gültigen Normen der SAE J 453. Um die hohe Leistung und Funktionssicherheit zu gewährleisten, setzt es voraus, dass Rohrverschraubungskomponenten eingesetzt und Montageanleitungen beachtet werden. ORFS type unions (0-lLok) comply with the respective valid SAE J453 standards. High performance and functional safety presupposes the use of appropriate pipe union components and the installation instructions are observed. www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de - 383 -
Technische Daten technical data Die ORFS-Verschraubungen bestehen aus vier Teilen: - Verschraubungskörper - O-Ring - Überwurfmutter - Stützhülse Montage der ORFS-Verschraubung: Überwurfmutter handfest anziehen, danach mit einem Drehmomentschlüssel bis zum jeweiligen Anzugsdrehmoment festziehen. The ORFS unions comprise four parts: - Union body - O-ring - Tap nuts - Support sleeve To install the ORFS union: Do up the cap nut tight by hand before using a torque wrench to tightening with the respective tightening torques. Anzugsdrehmomente für ORFS-Rohrverschraubungen: Tightening torques for ORFS pipe Rohr Aussendurchmesser Gewinde thread Anzugsdrehmomente tightening torques +0% mm Zoll/inch (UNF-UN) Nm 6 /4 9/6-8 5 8 /6-6 25 0 3/8 /6-6 25 2 /2 3/6-6 40 4-4 60 5-4 60 6 5/8-4 60 8 3/6-2 90 20 3/4 3/6-2 90 22 7/6-2 30 25 7/6-2 30 28 /6-2 80 30 /6-2 80 32 /4 /6-2 80 35 2-2 200 38 /2 2-2 200-0% Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
ORFS Löthülsen für metrisches Rohr ORFS brazing sleeves for metric pipe Lötanschluss Rohr-Ø/mm (d) brazing connection/pipe-ø/mm (d) für Überwurfmutter for union nut LH-O 6 9/6-8 44 0 9 06 LH-O 8 /6-6 44 0 92 08 LH-O 0 /6-6 44 0 92 0 LH-O 2 3/6-6 44 0 93 2 LH-O 4-4 44 0 94 4 LH-O 5-4 44 0 94 5 LH-O 6-4 44 0 94 6 LH-O 8 3/6-2 44 0 95 8 LH-O 20 3/6-2 44 0 95 20 LH-O 22 7/6-2 44 0 96 22 LH-O 25 7/6-2 44 0 96 25 LH-O 28 /6-2 44 0 97 28 LH-O 30 /6-2 44 0 97 30 LH-O 32 /6-2 44 0 97 32 LH-O 35 2-2 44 0 98 35 LH-O 38 2-2 44 0 98 38 ORFS Löthülsen für zölliges Rohr ORFS brazing sleeves for inch pipe Lötanschluss Rohr-Ø/mm (d) brazing connection/pipe-ø/mm (d) für Überwurfmutter for union nut LH-O /4" 9/6-8 44 02 9 32 LH-O 3/8" /6-6 44 02 92 33 LH-O /2" 3/6-6 44 02 93 34 LH-O 5/8" -4 44 02 94 35 LH-O 5/8" 7/6-2 44 02 96 35 LH-O 3/4" 3/6-2 44 02 95 36 LH-O 3/4" 7/6-2 44 02 96 36 LH-O 7/8" 7/6-2 44 02 96 78 LH-O " 7/6-2 44 02 96 37 LH-O /4" /6-2 44 02 97 38 LH-O /2" 2-2 44 02 98 39 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
Überwurfmuttern ORFS cap nuts ORFS Gewinde: thread: Rohranschluss pipe connection Gewinde thread Schlüsselweite width across flats M-O 6 9/6-8 9 44 03 9 00 M-O 8/0 /6-6 22 44 03 92 00 M-O 2 3/6-6 26 44 03 93 00 M-O 4/5/6-4 30 44 03 94 00 M-O 8/20 3/6-2 36 44 03 95 00 M-O 22/25 7/6-2 4 44 03 96 00 M-O 28/30/32 /6-2 50 44 03 97 00 M-O 35/38 2-2 60 44 03 98 00 Gegenmuttern counter nuts Gewinde: thread: Gewinde thread Schlüsselweite width across flats GM-O 9/6-8 9 44 09 9 00 GM-O /6-6 24 44 09 92 00 GM-O 3/6-6 27 44 09 93 00 GM-O -4 32 44 09 94 00 GM-O 3/6-2 38 44 09 95 00 GM-O 7/6-2 46 44 09 96 00 GM-O /6-2 50 44 09 97 00 GM-O 2-2 60 44 09 98 00 Schott Einschraubstutzen ORFS/BSP bulkhead screw-in unions ORFS/BSP Schottanschlussgewinde: Außengewinde mit Flachdichtung und O-Ring, amerikanisches Normgew. UNF-UN : Whitworth Rohrgewinde (BSPP), zylindrisch Abdichtung: durch O-Ring und Kammerring bulkhead : external thread with flat sealing and chamber ring, : Whitworth pipe thread (BSPP), cylindrical sealing: by O-ring and chamber ring Schottanschlussgewinde ORFS bulkhead ORFS SES-OR 9/6"-8 R /4" 44 44 9 32 SES-OR 9/6"-8 R 3/8" 44 44 9 33 SES-OR /6"-6 R 3/8" 44 44 92 33 SES-OR 3/6"-6 R /4" 44 44 93 32 SES-OR 3/6"-6 R /2" 44 44 93 34 SES-OR "-4 R /2" 44 44 94 34 SES-OR "-4 R 3/4" 44 44 94 36 SES-OR 3/6"-2 R /2" 44 44 95 34 SES-OR 3/6"-2 R 3/4" 44 44 95 36 SES-OR 7/6"-2 R " 44 44 96 37 SES-OR /6"-2 R /4" 44 44 97 38 SES-OR 2"-2 R /2" 44 44 98 39 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
Schott Einschraubstutzen ORFS/metrisch bulkhead screw-in unions ORFS/metric Schottgewinde: Außengewinde mit Flachdichtung und O-Ring, amerik. Normgewinde UNF-UN : metrisches Feingewinde, zylindrisch Abdichtung: durch O-Ring und Kammerring bulkhead thread: ext. thread with flat sealing and chamber ring, americ. standard thread UNF-UN : metric fine thread, cylindrical sealing: by O-ring and chamber ring Schottanschlussgewinde ORFS bulkhead ORFS SES-OM 3/6"-6 M 22X,5 44 45 93 07 SES-OM "-4 M 22X,5 44 45 94 07 SES-OM 3/6"-2 M 30X,5 44 45 95 SES-OM 7/6"-2 M 30X,5 44 45 96 gerade Einschraubverschraubungen ORFS, weichdichtend - metrisch straight screw-in unions ORFS, soft seal - metric : Außengewinde mit Flachdichtung und O-Ring, amerik. Normgewinde UNS-UN : metrisches Feingewinde, zylindrisch Abdichtung: durch O-Ring und Kammerring : ext. thread with flat sealing and chamber ring, americ. standard thread UNS-UN : metric fine thread, cylindrical sealing: by O-ring and chamber ring 420 GE-OM 9/6-8 M 2X,5 44 3 9 02 420 GE-OM 9/6-8 M 4X,5 44 3 9 03 350 GE-OM /6-6 M 6X,5 44 3 92 04 30 GE-OM 3/6-6 M 8X,5 44 3 93 05 235 GE-OM -4 M 22X,5 44 3 94 07 50 GE-OM 3/6-2 M 27X2 44 3 95 0 50 GE-OM 7/6-2 M 33X2 44 3 96 3 25 GE-OM /6-2 M 42X2 44 3 97 6 00 GE-OM 2-2 M 48X2 44 3 98 7 gerade Einschraubverschraubungen ORFS, kegelig - zöllig straight screw-in unions ORFS, tapered - inch : Außengewinde mit Flachdichtung und O-Ring, amerik. Normgewinde UNS-UN : Whitworth Rohrgewinde (BSPT), kegelig Einschraubzapfen: Form C (DIN 3852) Abdichtung: durch Kegelgewinde : ext. thread with flat sealing and chamber ring, americ. standard thread UNS-UN : Whitworth pipe thread (BSPT), tapered screw-in plug: form C (DIN 3852) sealing: by tapered thread 420 GE-OR 9/6-8 R /4" keg. 44 4 9 52 420 GE-OR /6-6 R 3/8" keg. 44 4 92 53 250 GE-OR 3/6-6 R /2" keg. 44 4 93 54 250 GE-OR -4 R /2" keg. 44 4 94 54 75 GE-OR 3/6-2 R 3/4" keg. 44 4 95 56 50 GE-OR 3/6-2 R " keg. 44 4 95 57 50 GE-OR 7/6-2 R " keg. 44 4 96 57 25 GE-OR /6-2 R /4" keg. 44 4 97 58 00 GE-OR 2-2 R /2" keg. 44 4 98 59 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
gerade Einschraubverschraubungen ORFS, weichdichtend - zöllig straight screw-in unions ORFS, soft seal - inch : Außengewinde mit Flachdichtung und O-Ring, : Whitworth Rohrgewinde (BSPP), zylindrisch Abdichtung: durch O-Ring und Kammerring : external thread with flat sealing and chamber ring, : Whitworth pipe thread (BSPP), cylindrical sealing: by O-ring and chamber ring 420 GE-OR 9/6-8 R /8" 44 9 3 420 GE-OR /6-6 R /4" 44 92 32 420 GE-OR /6-6 R 3/8" 44 92 33 420 GE-OR 3/6-6 R 3/8" 44 93 33 300 GE-OR 3/6-6 R /2" 44 93 34 300 GE-OR -4 R /2" 44 94 34 75 GE-OR 3/6-2 R 3/4" 44 95 36 50 GE-OR 7/6-2 R " 44 96 37 50 GE-OR /6-2 R /4" 44 97 38 25 GE-OR 2-2 R /2" 44 98 39 gerade Einschraubverschraubungen ORFS - NPT straight screw-in unions ORFS - NPT : Außengewinde mit Flachdichtung und O-Ring, : NPT Abdichtung: durch Kegelgewinde : external thread with flat sealing and chamber ring, : NPT sealing: by tapered thread 345 GE-OR 9/6-8 R /8" NPT 44 2 9 8 275 GE-OR 9/6-8 R /4" NPT 44 2 9 82 20 GE-OR 9/6-8 R 3/8" NPT 44 2 9 83 275 GE-OR /6-6 R /4" NPT 44 2 92 82 20 GE-OR /6-6 R 3/8" NPT 44 2 92 83 20 GE-OR /6-6 R /2" NPT 44 2 92 84 20 GE-OR 3/6-6 R 3/8" NPT 44 2 93 83 20 GE-OR 3/6-6 R /2" NPT 44 2 93 84 70 GE-OR 3/6-6 R 3/4" NPT 44 2 93 85 20 GE-OR -4 R /2" NPT 44 2 94 84 70 GE-OR -4 R 3/4" NPT 44 2 94 85 70 GE-OR 3/6-2 R 3/4" NPT 44 2 95 85 40 GE-OR 3/6-2 R " NPT 44 2 95 86 40 GE-OR 7/6-2 R " NPT 44 2 96 86 80 GE-OR /6-2 R /4" NPT 44 2 97 87 70 GE-OR 2-2 R /2" NPT 44 2 98 88 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
gerade Einschraubverschraubungen ORFS - UNF straight screw-in unions ORFS - UNF : Außengewinde mit Flachdichtung und O-Ring, : Abdichtung: durch O-Ring : external thread with flat sealing and chamber ring, : american standard thread, UNF-UN sealing: by O-ring 345 GE-OR 9/6-8 7/6-20 UNF 44 5 9 4 345 GE-OR 9/6-8 /2-20 UNF 44 5 9 42 345 GE-OR 9/6-8 9/6-8 UNF 44 5 9 43 30 GE-OR 9/6-8 3/4-6 UNF 44 5 9 44 345 GE-OR /6-6 7/6-20 UNF 44 5 92 4 345 GE-OR /6-6 /2-20 UNF 44 5 92 42 345 GE-OR /6-6 9/6-8 UNF 44 5 92 43 30 GE-OR /6-6 3/4-6 UNF 44 5 92 44 345 GE-OR 3/6-6 9/6-8 UNF 44 5 93 43 30 GE-OR 3/6-6 3/4-6 UNF 44 5 93 44 240 GE-OR 3/6-6 7/8-4 UNF 44 5 93 45 30 GE-OR -4 3/4-6 UNF 44 5 94 44 240 GE-OR -4 7/8-4 UNF 44 5 94 45 240 GE-OR -4 /6-2 UNF 44 5 94 76 240 GE-OR 3/6-2 7/8-4 UNF 44 5 95 45 240 GE-OR 3/6-2 /6 UNF 44 5 95 76 20 GE-OR 3/6-2 5/6-2 UNF 44 5 95 77 240 GE-OR 7/6-2 /6-2 UNF 44 5 96 76 20 GE-OR 7/6-2 5/6-2 UNF 44 5 96 77 70 GE-OR 7/6-2 5/8-2 UNF 44 5 96 78 20 GE-OR /6-2 5/6-2 UNF 44 5 97 77 70 GE-OR /6-2 5/8-2 UNF 44 5 97 78 40 GE-OR /6-2 7/8-2 UNF 44 5 97 79 40 GE-OR 2-2 7/8-2 UNF 44 5 98 79 gerade Adapter ORFS / JIC straight adapters ORFS / JIC Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Außengewinde mit 74 Konus, thread : external thread with flat sealing and chamber ring, thread 2: external thread with 74 cone, ORFS ORFS JIC JIC 345 GR-OJ 9/6-8 7/6-20 44 6 9 4 345 GR-OJ /6-6 /2-20 44 6 92 42 345 GR-OJ /6-6 9/6-8 44 6 92 43 30 GR-OJ 3/6-6 3/4-6 44 6 93 44 240 GR-OJ -4 7/8-4 44 6 94 45 240 GR-OJ 3/6-2 /6-2 44 6 95 46 20 GR-OJ 7/6-2 5/6-2 44 6 96 47 20 GR-OJ /6-2 5/8-2 44 6 97 48 20 GR-OJ 2-2 7/8-2 44 6 98 49 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
Anschweißstutzen ORFS für metrisches Rohr weld connectors ORFS for metric pipe : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, für Rohr/mm for pipe/mm AS-O 9/6-8 6 44 8 9 06 AS-O 9/6-8 8 44 8 9 08 AS-O 9/6-8 0 44 8 9 0 AS-O /6-6 0 44 8 92 0 AS-O /6-6 2 44 8 92 2 AS-O 3/6-6 2 44 8 93 2 AS-O 3/6-6 4 44 8 93 4 AS-O 3/6-6 6 44 8 93 6 AS-O -4 6 44 8 94 6 AS-O -4 8 44 8 94 8 AS-O 3/6-2 8 44 8 95 8 AS-O 3/6-2 20 44 8 95 20 AS-O 3/6-2 22 44 8 95 22 AS-O 3/6-2 25 44 8 95 25 AS-O 7/6-2 25 44 8 96 25 AS-O 7/6-2 28 44 8 96 28 AS-O 7/6-2 32 44 8 96 32 AS-O /6-2 32 44 8 97 32 AS-O /6-2 35 44 8 97 35 AS-O /6-2 38 44 8 97 38 AS-O 2-2 38 44 8 98 38 Anschweißstutzen ORFS für zölliges Rohr weld connectors ORFS for inch pipe : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, für Rohr/zöllig for pipe/inch AS-O 9/6-8 3/8" 44 9 9 33 AS-O /6-6 /2" 44 9 92 34 AS-O 3/6-6 5/8" 44 9 93 35 AS-O -4 3/4" 44 9 94 36 AS-O 3/6-2 " 44 9 95 37 AS-O 7/6-2 /4" 44 9 96 38 AS-O /6-2 /2" 44 9 97 39 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
gerade Verschraubungen ORFS straight unions ORFS Anschlussewinde: Außengew. mit Flachdichtung und O-Ring, amerik. Normgewinde UNF-UN : ext. thread with flat sealing and chamber ring, americ. standard thread UNF-UN 420 G-O 9/6-8 44 06 9 00 420 G-O /6-6 44 06 92 00 420 G-O 3/6-6 44 06 93 00 420 G-O -4 44 06 94 00 420 G-O 3/6-2 44 06 95 00 420 G-O 7/6-2 44 06 96 00 280 G-O /6-2 44 06 97 00 280 G-O 2-2 44 06 98 00 gerade Reduzierverschraubungen ORFS straight reducer unions ORFS Anschlussewinde: Außengew. mit Flachdichtung und O-Ring, amerik. Normgewinde UNF-UN : ext. thread with flat sealing and chamber ring, americ. standard thread UNF-UN Gewinde Gewinde 2 thread thread 2 420 GR-O 9/6-8 /6-6 44 07 9 92 420 GR-O /6-6 3/6-6 44 07 92 93 420 GR-O 3/6-6 -4 44 07 93 94 420 GR-O -4 3/6-2 44 07 94 95 420 GR-O 3/6-2 7/6-2 44 07 95 96 420 GR-O 7/6-2 /6-2 44 07 96 97 gerade Adapter ORFS / Zoll (BSPP) straight adapters ORFS / inch (BSPP) Gewinde : Außengewinde mit 60 Aussenkung BSPP und Einschraubzapfen Form A für U-Seal Ring Gewinde 2: Außengewinde mit Flachdichtung und O-Ring, thread : external thread with 60 chamfering and screw-in nipple form A for U-seal ring thread 2: external thread with flat sealing and chamber ring, ORFS zöllig ORFS inch 420 GR-O 9/6-8 R /8" 44 0 9 3 420 GR-O 9/6-8 R /4" 44 0 9 32 420 GR-O 9/6-8 R 3/8" 44 0 9 33 420 GR-O /6-6 R /4" 44 0 92 32 420 GR-O /6-6 R 3/8" 44 0 92 33 300 GR-O /6-6 R /2" 44 0 92 34 420 GR-O 3/6-6 R /4" 44 0 93 32 420 GR-O 3/6-6 R 3/8" 44 0 93 33 300 GR-O 3/6-6 R /2" 44 0 93 34 75 GR-O 3/6-6 R 3/4" 44 0 93 36 420 GR-O -4 R 3/8" 44 0 94 33 300 GR-O -4 R /2" 44 0 94 34 75 GR-O -4 R 3/4" 44 0 94 36 300 GR-O 3/6-2 R /2" 44 0 95 34 75 GR-O 3/6-2 R 3/4" 44 0 95 36 50 GR-O 3/6-2 R " 440 95 37 75 GR-O 7/6-2 R 3/4" 44 0 96 36 50 GR-O 7/6-2 R " 44 0 96 37 50 GR-O 7/6-2 R /4" 44 0 96 38 50 GR-O /6-2 R /4" 44 0 97 38 75 GR-O 2-2 R /2" 44 0 98 39 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
gerade Adapter vormontiert ORFS/JIC straight adapters ORFS/JIC Gewinde : Überwurfmutter flachdichtend, Gewinde 2: Außengewinde mit 74 Konus, thread : union nut flat sealing, thread 2: external thread with 74 cone, 2 Gewinde thread Gewinde 2 thread 2 KOVO ORFS/AGJ 9/6-8 7/6-20 44 50 9 4 KOVO ORFS/AGJ 9/6-8 9/6-8 44 50 9 43 KOVO ORFS/AGJ /6-6 9/6-8 44 50 92 43 KOVO ORFS/AGJ 3/6-6 3/4-6 44 50 93 44 KOVO ORFS/AGJ -4 7/8-4 44 50 94 45 KOVO ORFS/AGJ 3/6-2 /6-2 44 50 95 46 KOVO ORFS/AGJ 7/6-2 5/6-2 44 50 96 47 gerade Adapter vormontiert JIC/ORFS straight adapters JIC/ORFS Gewinde : Innengewinde mit 74 Innekonus JIC, Gewinde 2: Außengewinde flachdichtend mit O-Ring, thread : internal thread with 74 internal cone JIC, thread 2: external thread flat sealing with O-ring, 2 Gewinde thread Gewinde 2 thread 2 KOVO AGJ/ORFS 9/6-8 7/6-20 44 5 9 4 KOVO AGJ/ORFS /6-6 7/6-20 44 5 92 4 KOVO AGJ/ORFS /6-6 9/6-8 44 5 92 43 KOVO AGJ/ORFS 3/6-6 3/4-6 44 5 93 44 KOVO AGJ/ORFS -4 7/8-4 44 5 94 45 KOVO AGJ/ORFS 3/6-2 /6-2 44 5 95 46 KOVO AGJ/ORFS 7/6-2 5/6-2 44 5 96 47 gerade Adapter, vormontiert ORFS / zöllig (BSPP) straight adapters, preasssembled ORFS / inch (BSPP) Gewinde : zölliges Außengew. mit 60 Aussenkung und Einschraubzapfen Form A für U-Seal Ring Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : internal thread inch with 60 chamfering and screw-in nipple form A for U-seal ring thread 2: union nut flat sealing ORFS, 2 420 EVGE-OR 9/6-8 R /4" 44 2 9 32 420 EVGE-OR /6-6 R /4" 44 2 92 32 420 EVGE-OR /6-6 R 3/8" 44 2 92 33 300 EVGE-OR /6-6 R /2" 44 2 92 34 420 EVGE-OR 3/6-6 R 3/8" 44 2 93 33 300 EVGE-OR 3/6-6 R /2" 44 2 93 34 300 EVGE-OR -4 R /2" 44 2 94 34 420 EVGE-OR -4 R 5/8" 44 2 94 35 75 EVGE-OR -4 R 3/4" 44 2 94 36 75 EVGE-OR 3/6-2 R 3/4" 44 2 95 36 50 EVGE-OR 3/6-2 R " 44 2 95 37 50 EVGE-OR 7/6-2 R " 44 2 96 37 50 EVGE-OR 7/6-2 R /4" 44 2 96 38 50 EVGE-OR /6-2 R /4" 44 2 97 38 25 EVGE-OR 2-2 R /2" 44 2 98 39 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
gerade Doppelverbinder ORFS straight double unions ORFS : Überwurfmutter flachdichtend, : union nut flat sealing, 420 GVO-O 9/6-8 44 7 9 00 420 GVO-O /6-6 44 7 92 00 420 GVO-O 3/6-6 44 7 93 00 420 GVO-O -4 44 7 94 00 420 GVO-O 3/6-2 44 7 95 00 420 GVO-O 7/6-2 44 7 96 00 280 GVO-O /6-2 44 7 97 00 280 GVO-O 2-2 44 7 98 00 Schottverschraubungen ORFS straight bulkhead unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and O-ring, UNF-UN 420 SV-O 9/6-8 44 08 9 00 420 SV-O /6-6 44 08 92 00 420 SV-O 3/6-6 44 08 93 00 420 SV-O -4 44 08 94 00 420 SV-O 3/6-2 44 08 95 00 420 SV-O 7/6-2 44 08 96 00 280 SV-O /6-2 44 08 97 00 280 SV-O 2-2 44 08 98 00 Winkel Einschraubverschraubungen ORFS 45 - NPT angle screw-in unions ORFS 45 - NPT : Außengewinde mit Flachdichtung und O-Ring, : NPT Abdichtung: durch Kegelgewinde : external thread with flat sealing and O-ring, : NPT sealing: by tapered thread 345 WE45-OR 9/6-8 R /8" NPT 44 29 9 8 275 WE45-OR 9/6-8 R /4" NPT 44 29 9 82 20 WE45-OR 9/6-8 R 3/8" NPT 44 29 9 83 275 WE45-OR /6-6 R /4" NPT 44 29 92 82 20 WE45-OR /6-6 R 3/8"NPT 44 29 92 83 20 WE45-OR /6-6 R /2" NPT 44 29 92 84 20 WE45-OR 3/6-6 R 3/8" NPT 44 29 93 83 20 WE45-OR 3/6-6 R /2" NPT 44 29 93 84 20 WE45-OR -4 R /2" NPT 44 29 94 84 70 WE45-OR 3/6-2 R 3/4" NPT 44 29 95 85 40 WE45-OR 7/6-2 R " NPT 44 29 96 86 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
Winkel Einschraubverschraubungen ORFS - NPT angle screw-in unions ORFS - NPT : Außengewinde mit Flachdichtung und O-Ring, : NPT Abdichtung: durch Kegelgewinde : external thread with flat sealing and O-ring, : NPT sealing: by tapered thread 345 WE-OR 9/6-8 R /8" NPT 44 24 9 8 275 WE-OR 9/6-8 R /4" NPT 44 24 9 82 275 WE-OR /6-6 R /4" NPT 44 24 92 82 20 WE-OR /6-6 R 3/8" NPT 44 24 92 83 20 WE-OR /6-6 R /2" NPT 44 24 92 84 20 WE-OR 3/6-6 R 3/8" NPT 44 24 93 83 20 WE-OR 3/6-6 R /2" NPT 44 24 93 84 70 WE-OR 3/6-6 R 3/4" NPT 44 24 93 85 20 WE-OR -4 R /2" NPT 44 24 94 84 70 WE-OR -4 R 3/4" NPT 44 24 94 85 70 WE-OR 3/6-2 R 3/4" NPT 44 24 95 85 40 WE-OR 7/6-2 R " NPT 44 24 96 86 einstellbare Winkel Verschraubungen ORFS 45 adjustable angle screw unions ORFS 45 Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : external thread with flat sealing and O-ring, thread 2: union nut flat sealing ORFS, 2 420 EVW45-O 9/6-8 44 32 9 00 420 EVW45-O /6-6 44 32 92 00 420 EVW45-O 3/6-6 44 32 93 00 420 EVW45-O -4 44 32 94 00 420 EVW45-O 3/6-2 44 32 95 00 420 EVW45-O 7/6-2 44 32 96 00 280 EVW45-O /6-2 44 32 97 00 280 EVW45-O 2-2 44 32 98 00 Winkel Schottverschraubungen ORFS 45 angle bulkhead unions ORFS 45 : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 WSV-O 45 9/6-8 44 46 9 00 420 WSV-O 45 /6-6 44 46 92 00 420 WSV-O 45 3/6-6 44 46 93 00 420 WSV-O 45-4 44 46 94 00 420 WSV-O 45 3/6-2 44 46 95 00 420 WSV-O 45 7/6-2 44 46 96 00 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
einstellbare Winkel Verschraubungen ORFS adjustable angle screw unions ORFS Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : external thread with flat sealing and O-ring, thread 2: union nut flat sealing ORFS, 420 EVW-O 9/6-8 44 28 9 00 420 EVW-O /6-6 44 28 92 00 420 EVW-O 3/6-6 44 28 93 00 420 EVW-O -4 44 28 94 00 420 EVW-O 3/6-2 44 28 95 00 420 EVW-O 7/6-2 44 28 96 00 280 EVW-O /6-2 44 28 97 00 280 EVW-O 2-2 44 28 98 00 2 einstellb. Winkel Einschraubverschr. ORFS 45, weichdichtend - zöllig adjustable angle screw-in unions ORFS 45, soft seal - inch : Außengewinde mit Flachdichtung und O-Ring, amerik. Normgewinde UNF-UN : Whitworth Rohrgewinde (BSPP), zylindrisch Abdichtung: durch O-Ring und Kammerring : ext. thread with flat sealing and chamber ring, americ. standard thread UNF-UN : Whitworth pipe thread (BSPP), cylindrical sealing: by O-ring and chamber ring 420 WE45-OR 9/6-8 R /8" 44 3 9 3 420 WE45-OR 9/6-8 R /4" 44 3 9 32 420 WE45-OR /6-6 R /4" 44 3 92 32 420 WE45-OR /6-6 R 3/8" 44 3 92 33 300 WE45-OR /6-6 R /2" 44 3 92 34 420 WE45-OR 3/6-6 R 3/8" 44 3 93 33 300 WE45-OR -4 R /2" 44 3 94 34 75 WE45-OR -4 R 3/4" 44 3 94 36 75 WE45-OR 3/6-2 R 3/4" 44 3 95 36 50 WE45-OR 3/6-2 R " 44 3 95 37 50 WE45-OR 7/6-2 R " 44 3 96 37 50 WE45-OR /6-2 R /4" 44 3 97 38 50 WE45-OR 2-2 R /4" 44 3 98 38 einstellb. Winkel Einschraubverschr. ORFS 45, weichdichtend - metrisch adjustable angle screw-in unions ORFS 45, soft seal - metric : Außengewinde mit Flachdichtung und O-Ring, : metrisches Feingewinde, zylindrisch Abdichtung: durch Dichtscheibe, O-Ring und Kammerring : external thread with flat sealing and chamber ring, : metric fine thread, cylindrical sealing: by seal plate, O-ring and chamber ring 420 WE45-OM 9/6-8 M 2X,5 44 47 9 2 420 WE45-OM /6-6 M 4X,5 44 47 92 4 420 WE45-OM /6-6 M 6X,5 44 47 92 6 420 WE45-OM 3/6-6 M 8X,5 44 47 93 8 420 WE45-OM -4 M 22X,5 44 47 94 22 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
einstellbare Winkel Einschraubverschraubungen ORFS 45 - UNF adjustable angle screw-in unions ORFS 45 - UNF : Außengewinde mit Flachdichtung und O-Ring, : Abdichtung: durch O-Ring und Dichtscheibe : external thread with flat sealing and chamber ring, : american standard thread, UNF-UN sealing: by O-ring and seal disc 345 WE45-OR 9/6-8 7/6-20 UNF 44 30 9 4 345 WE45-OR 9/6-8 9/6-8 UNF 44 30 9 43 345 WE45-=R /6-6 7/6-20 UNF 44 30 92 4 345 WE45-OR /6-6 9/6-8 UNF 44 30 92 43 30 WE45-OR /6-6 3/4-6 UNF 44 30 92 44 345 WE45-OR 3/6-6 9/6-8 UNF 44 30 93 43 345 WE45-OR 3/6-6 3/4-6 UNF 44 30 93 44 240 WE45-OR 3/6-6 7/8-4 UNF 44 30 93 45 30 WE45-OR -4 3/4-6 UNF 44 30 94 44 240 WE45-OR -4 7/8-4 UNF 44 30 94 45 240 WE45-OR -4 /6-2 UNF 44 30 94 46 240 WE45-OR 3/6-2 7/8-4 UNF 44 30 95 45 240 WE45-OR 3/6-2 /6-2 UNF 44 30 95 46 20 WE45-OR 3/6-2 5/6-2 UNF 44 30 95 47 240 WE45-OR 7/6-2 /6-2 UNF 44 30 96 46 20 WE45-OR 7/6-2 5/6-2 UNF 44 30 96 47 70 WE45-OR 7/6-2 5/8-2 UNF 44 30 96 48 70 WE45-OR /6-2 5/8-2 UNF 44 30 97 48 40 WE45-OR /6-2 7/8-2 UNF 44 30 97 49 40 WE45-OR 2-2 7/8-2 UNF 44 30 98 49 einstellb. Winkel Einschraubverschr. ORFS, weichdichtend - metrisch adjustable angle screw-in unions ORFS, soft seal - metric : Außengewinde mit Flachdichtung und O-Ring, : metrisches Feingewinde, zylindrisch Abdichtung: durch Dichtscheibe, O-Ring und Kammerring : external thread with flat sealing and chamber ring, : metric fine thread, cylindrical sealing: by seal plate, O-ring and chamber ring 420 WE-OM 9/6-8 M 2X,5 44 26 9 02 420 WE-OM /6-6 M 4X,5 44 26 92 03 350 WE-OM /6-6 M 6X,5 44 26 92 04 30 WE-OM 3/6-6 M 8X,5 44 26 93 05 235 WE-OM -4 M 22X,5 44 26 94 07 50 WE-OM 3/6-2 M 27X2 44 26 95 0 50 WE-OM 7/6-2 M 33X2 44 26 96 3 25 WE-OM /6-2 M 42X2 44 26 97 6 00 WE-OM 2-2 M 48X2 44 26 98 7 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
einstellbare Winkel Einschraubverschr. ORFS, weichdichtend - zöllig adjustable angle screw-in unions ORFS, soft seal - inch : Außengewinde mit Flachdichtung und O-Ring, : Whitworth Rohrgewinde (BSPP), zylindrisch Abdichtung: durch O-Ring und Kammerring : external thread with flat sealing and chamber ring, : Whitworth pipe thread (BSPP), cylindrical sealing: by O-ring and chamber ring 420 WE-OR 9/6-8 R /8" 44 25 9 3 420 WE-OR 9/6-8 R /4" 44 25 9 32 420 WE-OR 9/6-8 R 3/8" 44 25 9 33 420 WE-OR /6-6 R /4" 44 25 92 32 420 WE-OR /6-6 R 3/8" 44 25 92 33 300 WE-OR /6-6 R /2" 44 25 92 34 420 WE-OR 3/6-6 R /4" 44 25 93 32 420 WE-OR 3/6-6 R 3/8" 44 25 93 33 300 WE-OR 3/6-6 R /2" 44 25 93 34 420 WE-OR -4 R 3/8" 44 25 94 33 300 WE-OR -4 R /2" 44 25 94 34 75 WE-OR -4 R 3/4" 44 25 94 36 300 WE-OR 3/6-2 R /2" 44 25 95 34 75 WE-OR 3/6-2 R 3/4" 44 25 95 36 50 WE-OR 3/6-2 R " 44 25 95 37 75 WE-OR 7/6-2 R 3/4" 44 25 96 36 50 WE-OR 7/6-2 R " 44 25 96 37 50 WE-OR 7/6-2 R /4" 44 25 96 38 50 WE-OR /6-2 R " 44 25 97 37 50 WE-OR /6-2 R /4" 44 25 97 38 25 WE-OR /6-2 R /2" 44 25 97 39 25 WE-OR 2-2 R /2" 44 25 98 39 einstellbare Winkel Einschraubverschraubungen ORFS - UNF adjustable angle screw-in unions ORFS - UNF : Außengewinde mit Flachdichtung und O-Ring, : Abdichtung: durch O-Ring und Dichtscheibe : external thread with flat sealing and chamber ring, : american standard thread, UNF-UN sealing: by O-ring and seal disc 30 WE-OR 9/6-8 7/6-20 UNF 44 27 9 4 275 WE-OR 9/6-8 9/6-8 UNF 44 27 9 43 30 WE-OR /6-6 7/6-20 UNF 44 27 92 4 275 WE-OR /6-6 9/6-8 UNF 44 27 92 43 275 WE-OR /6-6 3/4-6 UNF 44 27 92 44 275 WE-OR 3/6-6 9/6-8 UNF 44 27 93 43 275 WE-OR 3/6-6 3/4-6 UNF 44 27 93 44 20 WE-OR 3/6-6 7/8-4 UNF 44 27 93 45 20 WE-OR 3/6-6 /6-2 UNF 44 27 93 46 20 WE-OR -4 9/6-8 44 27 94 43 275 WE-OR -4 3/4-6 UNF 44 27 94 44 20 WE-OR -4 7/8-4 UNF 44 27 94 45 20 WE-OR -4 /6-2 UNF 44 27 94 46 20 WE-OR 3/6-2 7/8-4 UNF 44 27 95 45 20 WE-OR 3/6-2 /6-2 UNF 44 27 95 46 70 WE-OR 3/6-2 5/6-2 UNF 44 27 95 47 20 WE-OR 7/6-2 /6-2 UNF 44 27 96 46 70 WE-OR 7/6-2 5/6-2 UNF 44 27 96 47 40 WE-OR 7/6-2 5/8-2 UNF 44 27 96 48 70 WE-OR /6-2 5/6-2 UNF 44 27 97 47 40 WE-OR /6-2 5/8-2 UNF 44 27 97 48 05 WE-OR /6-2 7/8-2 UNF 44 27 97 49 05 WE-OR 2-2 7/8-2 UNF 44 27 98 49 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
Winkel Verschraubungen ORFS angle screw unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 W-O 9/6-8 44 22 9 00 420 W-O /6-6 44 22 92 00 420 W-O 3/6-6 44 22 93 00 420 W-O -4 44 22 94 00 420 W-O 3/6-2 44 22 95 00 420 W-O 7/6-2 44 22 96 00 280 W-O /6-2 44 22 97 00 280 W-O 2-2 44 22 98 00 Winkel Reduzierverschraubungen ORFS angle reducer unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, Gewinde thread Gewinde 2 thread 2 420 WR-O 9/6-8 /6-6 44 22 9 92 420 WR-O 9/6-8 3/6-6 44 22 9 93 420 WR-O /6-6 3/6-6 44 22 92 93 420 WR-O 3/6-6 3/6-2 44 22 93 95 Winkel Schottverschraubungen ORFS angle bulkhead unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 WSV-O 9/6-8 44 23 9 00 420 WSV-O /6-6 44 23 92 00 420 WSV-O 3/6-6 44 23 93 00 420 WSV-O -4 44 23 94 00 420 WSV-O 3/6-2 44 23 95 00 420 WSV-O 7/6-2 44 23 96 00 280 WSV-O /6-2 44 23 97 00 280 WSV-O 2-2 44 23 98 00 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
einstellbare T-Verschraubungen ORFS adjustable tee unions ORFS Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : external thread with flat sealing and O-ring, thread 2: union nut flat sealing ORFS, 420 EVT-O 9/6-8 44 39 9 00 420 EVT-O /6-6 44 39 92 00 420 EVT-O 3/6-6 44 39 93 00 420 EVT-O -4 44 39 94 00 420 EVT-O 3/6-2 44 39 95 00 420 EVT-O 7/6-2 44 39 96 00 280 EVT-O /6-2 44 39 97 00 280 EVT-O 2-2 44 39 98 00 2 einstellbare T-Einschraubverschraubungen ORFS, weichdichtend - zöllig adjustable tee screw-in unions ORFS, soft seal - inch : Außengewinde mit Flachdichtung und O-Ring, : Whitworth Rohrgewinde (BSPP), zylindrisch Abdichtung: durch O-Ring und Kammerring : external thread with flat sealing and chamber ring, : Whitworth pipe thread (BSPP), cylindrical sealing: by O-ring and chamber ring 420 TE-OR 9/6-8 R /8" 44 35 9 3 420 TE-OR 9/6-8 R /4" 44 35 9 32 420 TE-OR /6-6 R /4" 44 35 92 32 420 TE-OR /6-6 R 3/8" 44 35 92 33 420 TE-OR 3/6-6 R 3/8" 44 35 93 33 300 TE-OR 3/6-6 R /2" 44 35 93 34 300 TE-OR -4 R /2" 44 35 94 34 75 TE-OR -4 R 3/4" 44 35 94 36 75 TE-OR 3/6-2 R 3/4" 44 35 95 36 50 TE-OR 7/6-2 R " 44 35 96 37 50 TE-OR /6-2 R /4" 44 35 97 38 25 TE-OR 2-2 R /2" 44 35 98 39 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
einstellbare T-Einschraubverschraubungen ORFS - UNF adjustable tee unions ORFS - UNF : Außengewinde mit Flachdichtung und O-Ring, : Abdichtung: durch O-Ring und Dichtscheibe : external thread with flat sealing and chamber ring, : american standard thread, UNF-UN sealing: by O-ring and seal disc 30 TE-OR 9/6-8 7/6-20 UNF 44 37 9 4 275 TE-OR /6-6 9/6-8 UNF 44 37 92 43 275 TE-OR 3/6-6 3/4-6 UNF 44 37 93 44 20 TE-OR -4 7/8-4 UNF 44 37 94 45 20 TE-OR 3/6-2 /6-2 UNF 44 37 95 46 70 TE-OR 7/6-2 5/6-2 UNF 44 37 96 47 40 TE-OR /6-2 5/8-2 UNF 44 37 97 48 05 TE-OR 2-2 7/8-2 UNF 44 37 98 49 T-Verschraubungen ORFS tee unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 T-O 9/6-8 44 33 9 00 420 T-O /6-6 44 33 92 00 420 T-O 3/6-6 44 33 93 00 420 T-O -4 44 33 94 00 420 T-O 3/6-2 44 33 95 00 420 T-O 7/6-2 44 33 96 00 280 T-O /6-2 44 33 97 00 280 T-O 2-2 44 33 98 00 einstellbare L-Verschraubungen ORFS adjustable L-unions ORFS Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : external thread with flat sealing and O-ring, thread 2: union nut flat sealing ORFS, 2 420 EVL-O 9/6-8 44 38 9 00 420 EVL-O /6-6 44 38 92 00 420 EVL-O 3/6-6 44 38 93 00 420 EVL-O -4 44 38 94 00 420 EVL-O 3/6-2 44 38 95 00 420 EVL-O 7/6-2 44 38 96 00 280 EVL-O /6-2 44 38 97 00 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
L-Schottverschraubungen ORFS L-bulkhead unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 LSV-ORFS 9/6-8 44 48 9 00 420 LSV-ORFS /6-6 44 48 93 00 420 LSV-ORFS 3/6-6 44 48 94 00 420 LSV-ORFS -4 44 48 96 00 280 LSV-ORFS 3/6-2 44 48 97 00 einstellbare L-Verschraubungen ORFS, vormontiert adjustable L-unions ORFS, preassembled Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : external thread with flat sealing and O-ring, thread 2: union nut flat sealing ORFS, 2 420 EVL-VO-O 9/6-8 44 40 9 00 420 EVL-VO-O /6-6 44 40 92 00 420 EVL-VO-O 3/6-6 44 40 93 00 420 EVL-VO-O -4 44 40 94 00 420 EVL-VO-O 3/6-2 44 40 95 00 420 EVL-VO-O 7/6-2 44 40 96 00 2 einstellb. L-Verschraubungen ORFS, vormontiert, weichdichtend - zöllig adjustable L-unions ORFS, preassembled, soft seal - inch : Außengewinde mit Flachdichtung und O-Ring, : Whitworth Rohrgewinde (BSPP), zylindrisch Abdichtung: durch O-Ring und Kammerring : external thread with flat sealing and chamber ring, : Whitworth pipe thread (BSPP), cylindrical sealing: by O-ring and chamber ring 420 LE-OR 9/6-8 R /8" 44 34 9 3 420 LE-OR 9/6-8 R /4" 44 34 9 32 420 LE-OR /6-6 R /4" 44 34 92 32 420 LE-OR /6-6 R 3/8" 44 34 92 33 420 LE-OR 3/6-6 R 3/8" 44 34 93 33 300 LE-OR 3/6-6 R /2" 44 34 93 34 300 LE-OR -4 R /2" 44 34 94 34 75 LE-OR -4 R 3/4" 44 34 94 36 75 LE-OR 3/6-2 R 3/4" 44 34 95 36 50 LE-OR 3/6-2 R " 44 34 95 37 50 LE-OR 7/6-2 R " 44 34 96 37 50 LE-OR /6-2 R /4" 44 34 97 38 25 LE-OR 2-2 R /2" 44 34 98 39 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
einstellbare L-Einschraubverschraubungen ORFS - UNF adjustable tee unions ORFS - UNF : Außengewinde mit Flachdichtung und O-Ring, : Abdichtung: durch O-Ring und Dichtscheibe : external thread with flat sealing and chamber ring, : american standard thread, UNF-UN sealing: by O-ring and seal disc 30 LE-OR 9/6-8 7/6-20 UNF 44 36 9 4 275 LE-OR /6-6 9/6-8 UNF 44 36 92 43 275 LE-OR 3/6-6 3/4-6 UNF 44 36 93 44 20 LE-OR -4 7/8-4 UNF 44 36 94 45 20 LE-OR 3/6-2 /6-2 UNF 44 36 95 46 70 LE-OR 7/6-2 5/6-2 UNF 44 36 96 47 40 LE-OR /6-2 5/8-2 UNF 44 36 97 48 Kreuzverschraubungen ORFS, vormontiert cross unions ORFS, preassembled Überwurfmutter flachdichtend ORFS, union nut flat sealing ORFS, 420 KVO-O 9/6-8 44 4 9 00 420 KVO-O /6-6 44 4 92 00 420 KVO-O 3/6-6 44 4 93 00 420 KVO-O -4 44 4 94 00 420 KVO-O 3/6-2 44 4 95 00 420 KVO-O 7/6-2 44 4 96 00 Kreuzverschraubungen ORFS cross unions ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 K-O 9/6-8 44 42 9 00 420 K-O /6-6 44 42 92 00 420 K-O 3/6-6 44 42 93 00 420 K-O -4 44 42 94 00 420 K-O 3/6-2 44 42 95 00 420 K-O 7/6-2 44 42 96 00 280 K-O /6-2 44 42 97 00 280 K-O 2-2 44 42 98 00 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4
Gewindereduzierungen ORFS thread reducers Gewinde : Außengewinde mit Flachdichtung und O-Ring, Gewinde 2: Überwurfmutter flachdichtend ORFS, thread : external thread with flat sealing and O-ring, thread 2: union nut flat sealing ORFS, Innengewinde internal thread 420 RI-O 9/6-8 /6-6 44 20 9 92 420 RI-O 9/6-8 3/6-6 44 20 9 93 420 RI-O 9/6-8 -4 44 20 9 94 420 RI-O 9/6-8 3/6-2 44 20 9 95 420 RI-O /6-6 3/6-6 44 20 92 93 420 RI-O /6-6 -4 44 20 92 94 420 RI-O /6-6 3/6-2 44 20 92 95 420 RI-O 3/6-6 -4 44 20 93 94 420 RI-O 3/6-6 3/6-2 44 20 93 95 420 RI-O 3/6-6 7/6-2 44 20 93 96 420 RI-O -4 3/6-2 44 20 94 95 420 RI-O -4 7/6-2 44 20 94 96 420 RI-O 3/6-2 7/6-2 44 20 95 96 280 RI-O 3/6-2 /6-2 44 20 95 97 280 RI-O 7/6-2 /6-2 44 20 96 97 2 2 Verschlussschrauben ORFS screw plugs ORFS : Außengewinde mit Flachdichtung und O-Ring, : external thread with flat sealing and chamber ring, 420 VS-O 9/6-8 44 04 9 00 420 VS-O /6-6 44 04 92 00 420 VS-O 3/6-6 44 04 93 00 420 VS-O -4 44 04 94 00 420 VS-O 3/6-2 44 04 95 00 420 VS-O 7/6-2 44 04 96 00 280 VS-O /6-2 44 04 97 00 280 VS-O 2-2 44 04 98 00 Verschlusskappen ORFS screw caps ORFS Gewinde: Überwurfmutter flachdichtend, thread: union nut flat sealing, Gewinde thread 420 VKA-O 9/6-8 44 05 9 00 420 VKA-O /6-6 44 05 92 00 420 VKA-O 3/6-6 44 05 93 00 420 VKA-O -4 44 05 94 00 420 VKA-O 3/6-2 44 05 95 00 420 VKA-O 7/6-2 44 05 96 00 280 VKA-O /6-2 44 05 97 00 280 VKA-O 2-2 44 05 98 00 www.schmitter-hydraulik.de kontakt@schmitter-hydraulik.de
O-Ringe für ORFS O-rings for ORFS 90 Shore O-Ringe für stirnseitige Abdichtung (ORFS) O-rings for flat face seals (ORFS) Gewinde thread Innen-Ø/mm internal-ø/mm Stärke thickness. 9/6"-8 7,66,78 44 43 9 00 /6"-6 9,95,78 44 43 92 00 3/6"-6 2,42,78 44 43 93 00 "-4 5,6,78 44 43 94 00 3/6"-2 8,77,78 44 43 95 00 7/6"-2 23,52,78 44 43 96 00 /6"-2 29,87,78 44 43 97 00 2"-2 37,82,78 44 43 98 00 Schmitter Hydraulik GmbH 97450 Arnstein Tel.: +49 (0) 93 63/60-0 Fax: 60-4