Kupfer Programmieranleitung CADAS 100 LPG 158 Küvetten-Test LCK 529 Seite 1 Ausgabe 98/04 Achtung! Das Ausgabedatum dieser Programmieranleitung muß mit dem Ausgabedatum der Arbeitsvorschrift der Reagenzien identisch sein. Nur so ist gewährleistet, daß Sie die korrekten Daten in Ihr Gerät einprogrammieren. Hinweis! Sollten Sie während der Programmierung einen Fehler machen, können Sie die letzte Eingabe durch Drücken der Taste auf der Tastatur rückgängig machen. Die Eingabezeichen R und L bezeichnen die rechte und linke Taste. Löschen des bisher verwendeten LCK 529 Programms Programm CPRG (Löschen eines Testes) anwählen. Taste unter Symbol»529«anwählen. Taste unter»clear«bestätigen. Taste unter» > «bzw.» «bestätigen. Danach Rücksprung zur Hauptebene. Programmierung von LCK 529 Kupfer Kupfer -Anzeige Eingabe Programmnummer: z. B. 1 Name: KUPFER Symbol: L $ 529 Anzahl der Meßpunkte: 1 Programm PRG (Programmierung eines Testes, siehe Seite 1 und 2) anwählen. Faktor: = 1.11 Faktor: 2 = -0.016 Zusatz 1 : Die komplette Dateneingabe wird auf dem Drucker dokumentiert. Die vollständige Übernahme in den Speicher wird durch den Ausdruck»gespeichert«bestätigt. Bitte vergleichen Sie den Ausdruck nochmals mit den einzugebenden Daten.
Copper Programming instructions CADAS 100 LPG 185 Cuvette-Test LCK 529 Page 1 Attention! The edition date of this programming instruction must be identical to the edition date of the intruction attached to the reagents. This is the only way to ensure that your instrument will be programmed with the correct data. Please note! If you make an error during programming, you can cancel the last entry by pressing the key on the keyboard. The input symbols R and L indicate the right and left keys respectively. Deletion of the old LCK 529 program Select the program CPRG (deletion of tests). Press function key below symbol»529«. Press function key below»clear«. Press function key below» > «resp.» «. Return to main program. Programming of LCK 529 Copper Select the program PRG (programming of a test, see page 1 and 2). Copper Input via keyboard Program number: for example 1 Name: COPPER Symbol: L $ 529 Number of measurement points: 1 C 1 = A 1 C 1 = A 1 x F 1 C 1 = A 1 x F 1 + A 0 C 1 = A 1 x F 1 + F 2 C 1 = A 1 x F 1 + F 2 + A C 2 = A Factor: = 1.11 Factor: 2 = -0.016 Extension 1 : All data entries are documented on the printer; their transfer to storage is confirmed by the printer message»stored«. You should check the printed data to ensure that all entries are correct.
Cuivre Instruction de programmation CADAS 100 LPG 186 Test en Cuve LCK 529 Page 1 Attention! La date d édition de ces instructions doit être identique à celle du mode d emploi des réactifs. Dans ce cas seulement, vous êtes assurés d entrer les bonnes données dans votre appareil. Conseil! En cas d erreur durant la programmation, vous pouvez revenir sur la dernière entrée en utilisant la touche sur le clavier. Les touches d édition R et L servent de touche droite et gauche. Supression du programme LCK 529 enregistré sous le mode»test«appuyer la touche sous EFFP. Appuyer la touche sous le symbole»529«. Visualisation du nom du test à effacer. Appuyer la touche sous»effacer«. Appuyer la touche sous» > «resp.» «. Retour au programme principal. Programmation du LCK 529 Cuivre Cuivre Commande sur le clavier Numéro de programme: par example 1 Nom: CUIVRE Symbole: L $ 529 Nombre de points de mesure: 1 Facteur: = 1.11 Facteur: 2 = -0.016 Sélectionner le programme PRG (pour programmer un test, voir page 1 et 2). Supplément 1 : L ensemble des données est imprimé. Le transfert complet des données dans la mémoire est confirmé par le message»mémorisé«. Vérifiez que les données imprimées corresspondent bien à celles que vous avez entrées.
Kupfer Programmieranleitung CADAS 100 LPG 158 Küvetten-Test LCK 529 Seite 2 Ausgabe 98/04 Achtung! Das Ausgabedatum dieser Programmieranleitung muß mit dem Ausgabedatum der Arbeitsvorschrift der Reagenzien identisch sein. Nur so ist gewährleistet, daß Sie die korrekten Daten in Ihr Gerät einprogrammieren. Hinweis! Sollten Sie während der Programmierung einen Fehler machen, können Sie die letzte Eingabe durch Drücken der Taste auf der Tastatur rückgängig machen. Die Eingabezeichen R und L bezeichnen die rechte und linke Taste. Löschen des bisher verwendeten LCK 529 Programms (nach Einsatz des Crack-Set LCW 902) Programm CPRG (Löschen eines Testes) anwählen. Taste unter Symbol»529 C«drücken. Taste unter»clear«bestätigen. Taste unter» > «bzw.» «drücken. Danach Rücksprung zur Hauptebene. Programmierung von LCK 529 Kupfer (nach Einsatz des Crack-Set LCW 902) Kupfer -Anzeige Eingabe Programmnummer: z. B. 1 Name: KUPFER L - L C Symbol: L $ 529 L C Anzahl der Meßpunkte: 1 Programm PRG (Programmierung eines Testes, siehe Seite 1 und 2) anwählen. Faktor: = 1.332 Faktor: 2 = -0.019 Zusatz 1 : Die komplette Dateneingabe wird auf dem Drucker dokumentiert. Die vollständige Übernahme in den Speicher wird durch den Ausdruck»gespeichert«bestätigt. Bitte vergleichen Sie den Ausdruck nochmals mit den einzugebenden Daten.
Copper Programming instructions CADAS 100 LPG 185 Cuvette-Test LCK 529 Page 2 Attention! The edition date of this programming instruction must be identical to the edition date of the intruction attached to the reagents. This is the only way to ensure that your instrument will be programmed with the correct data. Please note! If you make an error during programming, you can cancel the last entry by pressing the key on the keyboard. The input symbols R and L indicate the right and left keys respectively. Deletion of the old LCK 529 program (after using the Crack-Set LCW 902) Select the program CPRG (deletion of tests). Press function key below symbol»529 C«. Press function key below»clear«. Press function key below» > «resp.» «. Return to main program. Programming of LCK 529 Copper (after using the Crack-Set LCW 902) Select the program PRG (programming of a test, see page 1 and 2). Copper Input via keyboard Program number: for example 1 Name: COPPER L - L C Symbol: L $ 529 L C Number of measurement points: 1 C 1 = A 1 C 1 = A 1 x F 1 C 1 = A 1 x F 1 + A 0 C 1 = A 1 x F 1 + F 2 C 1 = A 1 x F 1 + F 2 + A C 2 = A Factor: = 1.332 Factor: 2 = -0.019 Extension 1 : All data entries are documented on the printer; their transfer to storage is confirmed by the printer message»stored«. You should check the printed data to ensure that all entries are correct.
Cuivre Instruction de programmation CADAS 100 LPG 186 Test en Cuve LCK 529 Page 2 Attention! La date d édition de ces instructions doit être identique à celle du mode d emploi des réactifs. Dans ce cas seulement, vous êtes assurés d entrer les bonnes données dans votre appareil. Conseil! En cas d erreur durant la programmation, vous pouvez revenir sur la dernière entrée en utilisant la touche sur le clavier. Les touches d édition R et L servent de touche droite et gauche. Supression du programme LCK 529 (pour la détermination du cuivre en utilisant, soit le Crack-Set LCW 902) enregistré sous le mode»test«appuyer la touche sous EFFP. Appuyer la touche sous le symbole»529 C«. Visualisation du nom du test à effacer. Appuyer la touche sous»effacer«. Appuyer la touche sous» > «resp.» «. Retour au programme principal. Programmation du LCK 529 Cuivre (pour la détermination du cuivre en utilisant, soit le Crack-Set LCW 902) Sélectionner le programme PRG (pour programmer un test, voir page 1 et 2). Cuivre Commande sur le clavier Numéro de programme: par example 1 Nom: CUIVRE L - L C Symbole: L $ 529 L C Nombre de points de mesure: 1 Facteur: = 1.332 Facteur: 2 = -0.019 Supplément 1 : L ensemble des données est imprimé. Le transfert complet des données dans la mémoire est confirmé par le message»mémorisé«. Vérifiez que les données imprimées corresspondent bien à celles que vous avez entrées.