Industrielle Meß- und Prüftechnik Structure-Borne Noise Sensor BKS BKS Sensor with adapter to BKS03 thread Mai 20 Neustadt 12, 37073 Göttingen, Telefon: +(49) 551/54833-0, Fax: +(49) 551/54833-43 email: info@discom.de, http://www.discom.de
Design The BKS implements the design of the BKS03 with a very light-weight sensor on top of an elastic element. As an enhancement, the BKS is much slimmer and attaches to surfaces that are close to ribs and other obstructing surfaces. Furthermore, the cable is protected as it is guided in an internal pipe. The sensor used is of ICP type and has a a sensitivity of mv/g (1 mv/nm/s 2 ) These sensors weigh about 2 g and respond to frequencies up to 12 khz. The sensor is mounted on a silicon element, the top of it's casing contacting the unit under test. A small steel plate is attached to the device and electrically isolated to prevent malfunction. Because of the small weight, the relatively large contact area, and the absorption of vibration by the elastic element, resonance remains at a minimum. For the two figures below the transfer function of the Discom sensor and the transfer function of reference sensor were subtracted. Both sensors measured the structure-borne noise within a gear box. For figure A the Discom sensor was applied to the reference sensor, thereby ensuring that both sensors measure the same signal. For figure B the Discom sensor was applied to the gear box approximately 2cm from the reference sensor. Figure A exhibits almost linear transfer, both sensors being fed the same signal. Figure B is necessarily less perfect, because the difference actually measured owes in part to the varying signal at the two points on the gear box. Nevertheless no typical resonance frequencies were measured. dbg TrnsFnc 0.0-5.0 -.0-15.0-20.0 Fig. A. Deviation of transfer function of Discom-sensor to transfer-function of reference sensor. Discom sensor applied directly to reference sensor. Function shows no resonance frequencies. TrnsFnc 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 k Hz dbg 0.0-5.0 -.0-15.0-20.0 Fig. B. Deviation of transfer function of Discom sensor to transfer function of reference sensor. Discom sensor applied to a point on the gear box a short distance from the reference sensor. Function shows no resonance frequencies. 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 k Hz
Mechanical Drawing BKS 51,45 49,95 48,55 44,80 75,95 Ø12,00 Ø15,00 Ø16,00 Ø18,00 R 17,00 90,00 Wrench size 7x2 mm Details of BKS, all dimensions in mm 35,00 50,00 5,50 17,00 M6 M27x1,5 Ø16,00 M4 Ø12,00 5,50 3,00 11,00 8,00 Senkung-Bohrung M4 DIN 974 Details of adapter BKS03-A for BKS, all dimensions in mm
Adapter and Cable Configurations BKS FE ART-02616,40 Adapter BKS / BKS03 thread ART- 02612 5,50 7,80 18,00 12,00 M6 M27x1,5 11,40 40,00 24,40 50,50 Cable axial with silicon pipe Charge cable silicon 1,5m ART- 02619 Silicon pipe to protect the cable do not use inside the BKS the cable must have 5mm space for moving Cable lateral Accelerometer KS91E1 ICP type mv/g ART- 02618 Cable axial 2,00 Cable lateral DIS C O M Tel. +49 551 548330 Fax. +49 551 5483343 gez.:j. Lorenz BKS adapter MATERIAL: aluminium / silicon Scale: 1:1 2009-11-24 ZEICHN.NR. 091124-01 BLATT 1 von 1
Technical Data BKS Sensor axial Sensor transversal KS91E1 ICP type accelerometer with mv/g, or 1 mv/nm/s2 KS91F2 ICP type accelerometer with 25 mv/g, or 2,5 mv/nm/s2 Upper frequency limit: approx. khz Can be connected to Rotas systems configured as: ICP Input Minimum resonance due to small weight of 1,7 g and resonance absorption by silicon element. Adapts to uneven surfaces. Preload advice. axial transversal 2,00mm 4,0 N 5,00mm,0 N
Components of BKS ICP Sensor MMF KS91E1 mv/g ART-02618 BKS FE Elastic element ART-02616 Charge cable 1,5m with protective hose ART-02619 Measuring direction Adapter UNF -32/BNC ART-00281 BNC- Adapter ART-043 Cable BNC RG58 ART-00265x..m Discom PC with ICP 24V ICP Sensor MMF KS91F2 25mV/g ART-02800 Measuring direction Supplies for all systems: BKS Adapter BKS / M27x1,5 ART-02612 Lock nut M27x1,5 DIN EN 24035 ART-02043 BKS Adapter M3 / M6x0,5 ART-02623 Adapter to keep on using KS91D, KS91E on BKS Spanner 8mm ART-02657 Spanner 7mm ART-02732 D ISCC OM Industrielle Meß- und Prüftechnik Entwurf: Tel=+49/551/548330 Fax=+49/551/5483343 37073 Göttingen Germany J. Lorenz BKS Components Rev.2 Project: All projects Drawing 130307-02 Datum: 2013-03-07 Blatt: 1 von 1
KS91E1 IEPE-Beschleunigungsaufnehmer mit ringförmiger, isolierter Tastfläche aus Edelstahl M6x0,5 Gewinde zur Befestigung des Tastkopfes Empfindlichkeit: mv/g Hoher Dynamikbereich Hohe Resonanzfrequenz IEPE accelerometer with ringshaped, insulated probe made of stainless steel M6x0,5 thread to coupling the probe Sensitivity: mv/g Wide dynamic range High resonant frequency B ua (T) mg 5 Noise 0 1-5 0,1-0,01-15 0,001-20 20 60 0 C 0,1 1 Hz 0 30 Bua(f) 20 0-1 0 00 000 0000 Hz Arbeitstemperaturbereich T min/t max -20 / 120 C Piezosystem Piezo design Scherprinzip Shear design Spannungsübertragungsfaktor Voltage sensitivity B ua ± mv/g Linearer Frequenzgang (am Messkopf) Linear frequency range (on the probe) ±3dB ± ±5 4... 18.000 8....000 12... 8.000 Resonanzfrequenz Resonant frequency f r > 42 (+25dB) khz Messbereich Range a+ / a- ± 700 g (pk) Bruchbeschleunigung Destruction limit a max 8000 g (pk) Querrichtungsfaktor Transverse sensitivity G 90max < 5 Keramikkapazität Ceramic Capacitance C i 200 pf Ausgang Output IEPE kompatibel IEPE compatible Konstantstromversorgung Constant current supply I CONST 2..20 ma Arbeitspunktspannung Output bias voltage U BIAS @4mA; @25 C @Tmin @Tmax..12 +5-15 Nichtlinearität Total harmonic distortions THD @a +/a - 2 Ausgangsimpedanz Output resistance r a @4mA < 50 Ω Untere Grenzfrequenz Low cut-off frequency f ug -3dB 4 Hz Störgrößen Environmental characteristics Eigenrauschen Residual noise a n_rms (0,5.. 20k)Hz < 30 mg Temperaturkoeffizient der Empfindlichkeit Temperature coefficient of sensitivity a n @1 Hz @ Hz @0 Hz TK(Bua) @T< 20 C @T> 20 C 00 0-0, -0,13 Hz V µg/ Hz Temperatursprungempfindlichkeit b at 0,15 ms -2 /K Temperature transient sensitivity Magnetfeldempfindlichkeit Magnetic field sensitivity b ab - ms -2 /T Mechanische Daten Mechanical data Abmessungen Dimensions / h 7,8 / 15,5 mm Koppelflansch für Sensoraufnahme coupling flange / h M6x0,5 / 2,2 mm Masse ohne Kabel Weight without cable m 1,85 g Gehäusematerial Case material Kabelanschluss Cable connection Kontaktbuchse Socket Aluminium / Edelstahl Stainless steel axial Subminiatur M3 Subminiature M3 Befestigung Mounting Messkopf probe adhesive / antasten touch Schutzgrad / Isolation Protection grade / Insulation - / Isolierter Messkopf insulated probe Anschlusszubehör Connection Accessories 054 / 013T / 017 / 016 + 051/x Befestigungszubehör Mounting Accessories 002 Passende Messgeräte Suitable Electronics M28 / M32 / M68 / M8 / M208 / M12 / VibroMetra Bestellinformation Ordering Information KS91E1: Aufnehmer mit B ua± Sensor with B ua± /K Metra Meß- und Frequenztechnik in Radebeul e.k. Meißner Str. 58 D-01445 Radebeul Tel. +49-(0)351-836 2191 P.O.Box 01 01 13 D-01435 Radebeul Fax: +49-(0)351-836 2940 Ausgabe / Edition: 05/11 Internet: www.mmf.de Email: Info@MMF.de
KS91F2 IEPE-Beschleunigungsaufnehmer mit ringförmiger, isolierter Tastfläche aus Edelstahl Messachse in Querrichtung M6x0,5 Gewinde zur Befestigung des Tastkopfes geringes Rauschen IEPE accelerometer with ring-shaped, insulated probe made of stainless steel Main sensitivity in transverse direction M6x0,5 thread to coupling the probe Wide dynamic range low noise level B ua (T) 2 0-2 -4-6 -40 0 40 80 120 C 0 µg Noise 1 0,1 1 0 Hz Bua(f) 30 20 0-1 0 00 000 0000 Hz Arbeitstemperaturbereich T min/t max -30 / 120 C Piezosystem Piezo design Scherprinzip Shear design Spannungsübertragungsfaktor Voltage sensitivity B ua 25 ± 20 mv/g Messachse Axis of main sensitivity Linearer Frequenzgang (am Messkopf) Linear frequency range (on the probe) 3dB 5 Querrichtung Transverse direction 0,6... 12.500 1,1... 8.000 1,5 6.800 Resonanzfrequenz Resonant frequency f r < 30 (+25dB) khz Messbereich Range a+ / a- ± 240 g (pk) Bruchbeschleunigung Destruction limit a max 8000 g (pk) Querrichtungsfaktor Transverse sensitivity G 90max < 5 Keramikkapazität Ceramic Capacitance C i 200 pf Ausgang Output IEPE kompatibel IEPE compatible Konstantstromversorgung Constant current supply I CONST 2..20 ma Arbeitspunktspannung Output bias voltage U BIAS @4mA; @25 C @Tmin- Tmax 12..14 V Nichtlinearität Total harmonic distortions THD @a +/a - 2 Ausgangsimpedanz Output resistance r a @4mA < 60 Untere Grenzfrequenz Low cut-off frequency f ug -3dB 0,6 Hz Störgrößen Environmental characteristics Eigenrauschen Residual noise a n_rms (0,5.. 20k)Hz < 1,5 mg Temperaturkoeffizient der Empfindlichkeit Temperature coefficient of sensitivity a n TK(Bua) @1 Hz @ Hz @0 Hz @T=(-30..20) C @T=(20..60) C @T=(60..120) C 60 15 4 0,01-0,03-0,05 Hz µg/ Hz Temperatursprungempfindlichkeit b at 0,15 ms -2 /K Temperature transient sensitivity Magnetfeldempfindlichkeit Magnetic field sensitivity b ab 2 ms -2 /T Mechanische Daten Mechanical data Abmessungen Dimensions / h 8,5 / 16 mm Koppelflansch für Sensoraufnahme coupling flange / h M6x0,5 / 2,2 mm Masse ohne Kabel Weight without cable m 2,6 g Gehäusematerial Case material Kabelanschluss Cable connection Aluminium / Edelstahl Stainless steel axial zum Tastkopf axial to probe Kontaktbuchse Socket Subminiatur M3 Subminiature M3 Befestigung Mounting adhesive / antasten touch Schutzgrad / Isolation Protection grade / Insulation Bestellinformation Ordering Information - / Isolierter Messkopf insulated probe KS91F2: Aufnehmer mit B ua±20 Sensor with B ua±20 /K Metra Meß- und Frequenztechnik in Radebeul e.k. Ausgabe / Edition: 09/12 Meißner Str. 58 D-01445 Radebeul Tel. +49-(0)351-836 2191 P.O.Box 01 01 13 D-01435 Radebeul Fax: +49-(0)351-836 2940 Internet: www.mmf.de Email: Info@MMF.de