DS 201P DS 201P DRUCK & TEMPERATUR LEITENBERGER GMBH. Electronic. Pressure Switch. Pressure Port With Flush Welded Stainless Steel Diaphragm

Transkript

1 DRUCK & TEMPERATUR LEITENBERGER GMBH DS 0P Electronic Pressure Switch Pressure Port With Flush Welded Stainless Steel Diaphragm accuracy according to IEC 60770: 0. % FSO Electronic Pressure Switchter DS 0P Nominal pressure: from bar up to bar Contacts:, or independent PNP contacts, freely configurable Analog output: wire:... 0 ma wire: 0 0 ma / 0 0 V Special characteristics: indication of measured values on a digit LED display rotatable and configurable display module versions: ISversion Ex ia = intrinsically safe for gases Cooling element up to 00 C Customer specific versions The electronic pressure switch DS 0P is the successful combination of intelligent pressure switch digital display and is designed for universal applications in the mechanical engineering and other industries where a flush stainless steel diaphragm is necessary. This can be the case, for example, with higher viscous or slightly contaminated fluids. For usage with higher media temperature optionally a cooling element up to 00 C is available. Preferred areas of use are: Preferred used for: Plant and Machine Engineering Food Industry Viscous and pasty media DRUCK & TEMPERATUeitenberger GmbH Bahnhofstr. D78 Kirchentellinsfurt GERMANY Tel. +9 (0) Fax +9 (0) DTInfo@Leitenberger.de

2 DS 0P Input pressure ranges Nominal pressure [bar] Overpressure [bar] Burst pressure [bar] Contact PNP contact Options independent PNP contacts independent PNP contacts (possible with Mx, 8pin for... 0 ma/wire; V/wire on request) Max. switching current... 0 ma / and wire: contact rating ma, shortcircuit resistant; V switch = V S V V / Leiter: contact rating 00 ma, shortcircuit resistant Accuracy of contacts ± 0. % FSO Repeatability ± 0. % FSO Switching frequency max. 0 Hz Switching cycles > 00 x 0 6 Delay time sec max. contact for wire current signal with plug ISO 00 as well as wire current signal with Exprotection no contact possible with wire in combination with plug ISO 00 accuracy according to IEC limit point adjustment (nonlinearity, hysteresis, repeatability) Analogue output (optionally) / Supply wire current signal... 0 ma / V S =... 6 V DC permissible load: R max = [(V S V S min ) / 0.0 A] Ω response time: < 0 msec wire current signal with... 0 ma / V S =... 8 V DC Exprotection permissible load: R max = [(V S V S min ) / 0.0 A] Ω response time: < 0 msec wire current signal... 0 ma / V S = V DC adjustable (turndown of span max. :) permissible load: R max = 00 Ω response time: < 0. sec wire voltage signal V / V S =... 6 V DC permissible load: R min = 0 kω response time: < 0 msec without analogue output V S =... 6 V DC accuracy ± 0. % FSO with turndown of span the analogue signal is adjusted automatically to the new measuring range Thermal error (offset and span) / Permissible temperatures Thermal error ± 0. % FSO / 0 K in compensated range C Permissible temperatures medium: 0... C for filling fluid silicon oil 0... C for filling fluid food compatible oil electronics / environment: C storage: C Permissible temperature filling fluid silicon oil overpressure: 0 00 C vacuum: C medium for cooling element 00 C filling fluid food compatible oil overpressure: C vacuum: C an optional cooling element can influence thermal effects for offset and span depending on installation position and filling conditions max. temperature of the medium for overpressure > 0 bar: 0 C for 60 minutes with a max. environmental temperature of 0 Electrical protection Shortcircuit protection permanent Reverse polarity protection no damage, but also no function Electromagnetic compatibility emission and immunity according to EN 66 Mechanical stability Vibration g RMS ( Hz) according to DIN EN Shock 00 g / msec according to DIN EN Filling fluids Materials silicon oil food compatible oil with FDA approval (Mobil DTE FM ; Category Code: H; NSF Registration No.: 066) Pressure port stainless steel.0 (6 L) Housing stainless steel.0 (6 L) Display housing PA 6.6, Polycarbonate Seals (media wetted) standard: FKM (for media temperature 00 C) option: FFKM (for media temperature > 00 C) Diaphragm stainless steel. Media wetted parts pressure port, seals, diaphragm DRUCK & TEMPERATUeitenberger GmbH Bahnhofstr. D78 Kirchentellinsfurt GERMANY Tel. +9 (0) Fax +9 (0) DTInfo@Leitenberger.de

3 DS 0 P Explosion protection (only for 0 ma / wire) Approval AXDS 0P IBExU 06 ATEX 00 X zone : II G Ex ia IIC T Gb (connector) / II G Ex ia IIB T Gb (cable) Safety technical maximum values U i = 8 V, I i = 9 ma, P i = 660 mw, C 0 nf, L i 0 µh Max. switching current 6 70 ma (max. permissible inductivity:.7 mh) Max. temperatures for environment C Connecting cables cable capacitance: signal line/shield also signal line/signal line: 60 pf/m (by factory) cable inductance: signal line/shield also signal line/signal line: µh/m 6 the real switching current in the application depends on the power supply unit Miscellaneous Display digit, red 7segmentLED display, digit height 7 mm, range of indication ; accuracy 0. % ± digit; digital damping 0. 0 sec (programmable); measured value update sec (programmable) Current consumption wire signal output current: max. ma (without contacts) wire signal output current: approx. ma + signal current wire signal output voltage: approx. ma Ingress protection IP 6 Installation position any (standard calibration in a vertical position with the pressure port connection down) Weight min. 00 g (depending on mechanical connection) Operational life > 00 x 0 6 cycles CEconformity EMC Directive: 00/08/EC Pressure Equipment Directive: 97//EC (module A) 7 ATEX Directive 9/9/EC 7 This directive is only valid for devices with maximum permissible overpressure > 00 bar. Wiring diagrams wiresystem (current) wiresystem (current/voltage) p supply + supply A V S p supply + supply signal + contact A/V V S I contact contact I/U contact contact contact Pin configuration Electrical connection Supply + Supply Signal + (only for wire) Contact Contact Contact Contact Shield Mx plastic (pin) via pressure port Mx metal (pin) plug housing/ pressure port Mx plastic (8pin) 6 7 via pressure port ISO 00 ground contact Binder series 7 (pin) plug housing/ pressure port cable colours (DIN 700) wh (white) bn (brown) gn (green) gr (grey) pn (pink) gn/ye (green/yellow) Electrical connections (dimensions in mm) cable outlet PVC Ø =.9mm cable outlet PUR Ø =.7mm Mx (pin) Mx (8pin) ISO 00 Binder series 7 (pin) cable outlet 8 8 different cable types and lengths available, permissible temperature depends on kind of cable; standard: m PVC cable (without ventilation tube, permissible temperature: C) DRUCK & TEMPERATUeitenberger GmbH Bahnhofstr. D78 Kirchentellinsfurt GERMANY Tel. +9 (0) Fax +9 (0) DTInfo@Leitenberger.de

4 DS 0P Mechanical connection (dimensions in mm) G/" flush G/" flush G" flush 6 6 G/" flush G" flush cooling element with radial oring with radial oring 00 C 9 metric threads and other versions on request 6 This data sheet contains product specification, properties are not guaranteed. Subject to change without notice. 9 for pressure ranges P N 60 bar DRUCK & TEMPERATUeitenberger GmbH Bahnhofstr. D78 Kirchentellinsfurt GERMANY Tel. +9 (0) Fax +9 (0) DTInfo@Leitenberger.de

5 DS 0P DRUCK & TEMPERATUR LEITENBERGER GMBH Spezifikationsblatt / specification sheet DS 0P Messgröße relativ absolut Eingang [bar] Sondermessbereiche Analogausgang ohne 0 ma / -Leiter 0 0 V / -Leiter 0 ma / -Leiter, verstellbar Ex-Schutz 0 ma / -Leiter 0 7 E Schaltausgang, Schaltausgang, Schaltausgänge Schaltausgänge Genauigkeit 0, % Elektrischer Anschluss Stecker Mx (-polig) / Kunststoffausführung N 0 0 Stecker Mx (8-polig) / Kunststoffausführung M 0 Stecker Mx (-polig) / Metallausführung N 0 Stecker und Kabeldose ISO 00 Stecker Binder Serie 7 (-polig) Kabelausgang mit PVC-Kabel T A Mechanischer Anschluss G/" DIN 8 mit Z 0 0 G/" DIN 8 mit Z 0 G" DIN 8 mit Z G" DIN 8 mit rad. O-Ring und Z 7 G /" DIN 8 mit rad. O-Ring und Z Trennmembrane Edelstahl. (6L) 9 Dichtung FKM FFKM 7 Füllflüssigkeit Silikonöl Lebensmitteltaugliches Öl Sonderausführungen mit Temperaturentkoppler bis 00 C 6 bei Ex-Ausführung ist max. Schaltausgang möglich mit Stecker ISO 00 ist bei -Leiter Ausführung nur max. Schaltausgang möglich; bei -Leiter Ausführung ist kein Schaltausgang möglich Schaltausgänge und Mx, 8-polig nur in Kombination miteinander und mit... 0 ma/-leiter erhältlich; V/-Leiter auf Anfrage : m PVC-Kabel ohne Belüftungsschlauch (Temperatureinsatzbereich: - 70 C), auf Anfrage möglich für Nenndruckbereiche P N 00 bar 6 Temperaturentkoppler bis 00 C nicht möglich für Druckbereiche P N > 60 bar DRUCK & TEMPERATUeitenberger GmbH Bahnhofstr. D78 Kirchentellinsfurt GERMANY Tel. +9 (0) Fax +9 (0) DTInfo@Leitenberger.de eser Preisliste enthalten die Spezifikation der Produkte, nicht die Zusicherung von Eigenschaften. Ausführliche Informationen zu den Bestelloptionen könn nnen dem Datenblatt entnommen werden. Technische Änderungen vorbehalten. Die Angaben die