51 21 300 Fensterschacht-Abdeckleiste auf der Außenseite der Vordertür aus- und einbauen/austauschen Vordertürscheibe absenken. Fensterschacht-Abdeckleiste lösen; dabei von vorn nach hinten vorgehen. Hinweis: Sicherstellen, dass die Fensterschachtspalten (1) zwischen'a' Säulenverkleidung und hinterer Fensterleiste korrekt sind. RA Fensterschacht-Abdeckleiste auf der Außenseite der Vordertür aus- und einbauen/a BMW AG - TIS 28.05.2008 18:0 Ausgabestand (03/2006) Nur gültig bis zur nächsten DVD-Ausgabe Copyright Seite - 1
51 32 170 Türscheibe vorn links oder rechts ausbauen und einbauen bzw. ersetzen Erforderliche Spezialwerkzeuge: 51 3 240 Erforderliche Vorarbeiten: Türverkleidung vorn abbauen Fensterschacht-Abdeckleiste außen abbauen Unterlegscheiben (1) an Türfensterscheibe mit Spezialwerkzeug 51 3 240 lockern. Hinweis: Türfensterscheibe muss komplett geschlossen sein. Türscheibe auf Maß (1) absenken. 1 = 220 mm Achtung! Batterieminusleitung abklemmen. Unterlegscheiben (2) ausbauen. Anziehdrehmoment 51 32 1AZ. Scheibe vom Fensterheber (3) lösen und nach oben herausheben. Einbauhinweis: Türscheibe einstellen. RA Türscheibe vorn links oder rechts ausbauen und einbauen bzw. ersetzen BMW AG - TIS 28.05.2008 18:0 Ausgabestand (03/2006) Nur gültig bis zur nächsten DVD-Ausgabe Copyright Seite - 1
51 33 000 Elektrischen Fensterheber in Vordertür links oder rechts aus- und einbauen (ersetzen) Erforderliche Vorarbeiten: Türfensterscheibe vorn ausbauen Hochtonlautsprecher in Vordertür ausbauen Stopfen (1) entfernen. Schrauben (2) lösen. Anziehdrehmoment 51 33 1AZ. Schrauben (1) lösen. Anziehdrehmoment 51 33 2AZ. Schrauben (2) lösen. Anziehdrehmoment 51 33 3AZ. Seile von Klipps (3 und 4) aushängen. Um den Fensterhebermotor freizulegen, vordere Fensterheberschiene verschieben. Steckverbindung (1) vom Fensterhebermotor abziehen. Fensterheber von Vordertür ausbauen. Einbauhinweis: Fensterheber initialisieren. RA Elektrischen Fensterheber in Vordertür links oder rechts aus- und einbauen (erse BMW AG - TIS 28.05.2008 18:0 Ausgabestand (03/2006) Nur gültig bis zur nächsten DVD-Ausgabe Copyright Seite - 1
Achtung! Umlenkrolle (3) darf nicht aus Montageplatte (4) herausgezogen werden. Fensterheber muss in diesem Fall erneuert werden! Schrauben (1) max. 5 mm lockern (nicht lösen!). Spezialwerkzeug 00 9 318 zwischen Flachmotor (2) und Montageplatte (4) einschieben. Spezialwerkzeug 00 9 318 gegen Umlenkrolle (1) in Montageplatte (3) drücken. Schrauben lösen. Flachmotor (2) vorsichtig von Montageplatte (3) abheben. RA Flachmotor für Fensterheber vorn links oder rechts aus- und einbauen/ersetzen BMW AG - TIS 28.05.2008 18:0 Ausgabestand (03/2006) Nur gültig bis zur nächsten DVD-Ausgabe Copyright Seite - 2
67 62 000 Flachmotor für Fensterheber vorn links oder rechts aus- und einbauen/ersetzen Erforderliche Spezialwerkzeuge: 00 9 318 Erforderliche Vorarbeiten: Elektrischen Fensterheber in Vordertür ausbauen Schraube (1) lösen. Flachmotor von Fensterheberschiene (2) abbauen. Achtung! Beschädigungsgefahr! Folgenden Arbeitsschritt genauestens beachten, um eine Beschädigung des Fensterhebers zu vermeiden. RA Flachmotor für Fensterheber vorn links oder rechts aus- und einbauen/ersetzen BMW AG - TIS 28.05.2008 18:0 Ausgabestand (03/2006) Nur gültig bis zur nächsten DVD-Ausgabe Copyright Seite - 1
Once you have removed the mechanism from the door there are now 2 ways to go about it, 1) The easy way is to leave the motor in the gearing mechanism this way you do not have the risk of the cable getting tangles up and this is the approach I have taken, the only draw back is that when you remove the armature you will have to "screw" it out as it will not be free on the other end. This is by far the method I recommend, as i found it easier and quicker and this is the way I will continue the guide. 2) The other way is to remove the motor from the gearing mechanism as decribed in Clarkes guide as if you are going to replace the motor, this way you will be able to work with the motor more freely, but have the risk of tangling up the cable. Only use this method if you are more confident and are plannig to do more work as if replacing the bushes. Either way from above you will now have access to the motor and the gearing mechanism If you are following the 2nd method from above you will remove the motor at this stage, See below http://www.mini2.com/forum/printthread.php?t=149681 (4 of 13)11/03/08 1:06:48
Now this is where you remove the motor casing, by removing the 4 bolts holding the metal casing below. http://www.mini2.com/forum/printthread.php?t=149681 (5 of 13)11/03/08 1:06:48
Important note, mark which way the casing goes in, if it is out by 180 degree your motor will function the opposite way! Now remove the metal casing by pulling it of, remember there is a bearing on the end so pull it off perpendicular. It will be hard to pull off at the permanent magnets are attracted to the armature. http://www.mini2.com/forum/printthread.php?t=149681 (6 of 13)11/03/08 1:06:48
http://www.mini2.com/forum/printthread.php?t=149681 (7 of 13)11/03/08 1:06:48
(If you are following step 2 then the rotor may come out with the casing and will look like this http://www.mini2.com/forum/printthread.php?t=149681 (8 of 13)11/03/08 1:06:48
simply pull out the rotor from the metal casing.) Removing the armature, firstly dont panic the brushes will pop out, I will explain how to put these back together in a bit. Again here is what you do depending on which method you are following from above: 1)If the motor is still connected to the gearing ratio you will have to rotate the rotor to remove it this will inscrew the worm gear 2) If you have removed the motor from the gearing mechanism and the armature has not come out with the metal housing the rotor should just pull straight out. http://www.mini2.com/forum/printthread.php?t=149681 (9 of 13)11/03/08 1:06:48
Once the rotor is out, this is your fault, the armature is dirty hence poor contact with the brushes,(this motor was not as bad as the other one but i serviced it anyway) http://www.mini2.com/forum/printthread.php?t=149681 (10 of 13)11/03/08 1:06:48
I used a bit of 1600 wet and dry paper to clean the armature (it was dry!), remember patience, best way to do it i think is to hold the paper and turn the rotor that way you will be taking of a even amount. Once you finish it will look like this http://www.mini2.com/forum/printthread.php?t=149681 (11 of 13)11/03/08 1:06:48
Refitting the rotor into the housing. Although I intially thought that we have to hold the brushes on each side with a screwdriver and refit the rotor. I have found that on the opposite end to where the brushes make contact with the rotor there is a white cap. A slight nip with a screwdriver removes the cap and the spring can be removed. So move the brushes back, slip in the rotor, replace the spring and clip the cap back in place. http://www.mini2.com/forum/printthread.php?t=149681 (12 of 13)11/03/08 1:06:48
Now simply replace the metal housing on the motor (THE RIGHT WAY ROUND) and Voila you have saved the cost of a new motor. I did find it is possible to change the brushes, but you would have to resize the new brushes and solder them in. May be part II of the guide but for now its working fine. Hope you find this useful and any questions feel free to email me khurrumsattar@hotmail.com sjrainsford Dec 4th, 2007 06:52 PM Nice write up! I vote this should be a sticky forum entry! miniredcooper Dec 13th, 2007 08:52 AM Nice one - excellent instruction and information. Thanks. All times are GMT. The time now is 12:03 AM. vbulletin Version 3.6.7 Copyright 2000-2008, Jelsoft Enterprises Ltd. SEO by vbseo 3.0.0 http://www.mini2.com/forum/printthread.php?t=149681 (13 of 13)11/03/08 1:06:48
RealOEM.COM BMW R53 Cooper S EL.FRONT DOOR WINDOW LIFTING MECHANISM R53 Cooper S EL.FRONT DOOR WINDOW LIFTING MECHANISM RealOEM.com Home => Select another car => VEHICLE TRIM => DOORS / OUTSIDE MIRRORS Shopping cart. No items in cart. No. Description Supplement Qty From Up To Part Number Price Notes 01 WINDOW LIFTER, ELECTRIC, LEFT 1 06/2005 51337039451 See EBA 0032712 01 WINDOW LIFTER, ELECTRIC, RIGHT 1 06/2005 51337039452 See EBA 0032712 01 WINDOW LIFTER, ELECTRIC, LEFT 1 06/2005 51337162163 01 WINDOW LIFTER, ELECTRIC, RIGHT 1 06/2005 51337162164 02 DRIVE FOR WINDOW LIFTER, See HLI 1 06/2005 67626955875 FRONT LEFT AG4398122-03 02 DRIVE FOR WINDOW LIFTER, FRONT LEFT 1 06/2005 67626954275 ONLY IN CONJUNCTION WITH -- ADAPTER PLATE, LEFT 1 06/2005 51337197471 02 DRIVE FOR WINDOW LIFTER, FRONT RIGHT 1 06/2005 67626955876 02 DRIVE FOR WINDOW LIFTER, FRONT RIGHT 1 06/2005 67626954276 ONLY IN CONJUNCTION WITH -- ADAPTER PLATE, RIGHT 1 06/2005 51337197472 03 WASHER, WINDOW LIFTER 4 51337044403 04 SUPPORT WINDOW RAIL 2 51337075383 05 FILLISTER HEAD SCREW 6 07136800249 06 MOUNTING PARTS SET 1 51337031087 See EBA 0032712 07 CLAMP 1 51337132223 08 BASE, SIDE WINDOW 4 08/2004 51337141489 09 REPAIR KIT WINDOW LIFTER 1 51337177925 10 ADAPTER PLATE, LEFT 1 06/2005 51337197471 10 ADAPTER PLATE, RIGHT 1 06/2005 51337197472 Notes: SI, TÜV, SDB = Service Information (refer to TIS). EBA = Einbauanleitung (options installation manual). http://www.realoem.com/bmw/showparts.do?model=re31&mospid=48020&btnr=51_4271&hg=51&fg=10 (1 of 2)28-05-08 18:35:26