Analoges Ausgangsmodul BMT-AOP 887. Beschreibung Das BACnet MS/TP Modul mit analogen Ausgängen wurde für dezentrale Schaltaufgaben entwickelt. Es ist geeignet als Stell-größengeber, z.b. elektrische Lüftungs- und Mischklappen, Ventilstellungen usw. Von einem BACnet-Client können die Ausgänge über Standard-Objekte ausgegeben werden. Die Adressierung des Moduls und die Einstellung der Baudrate erfolgt über die beiden Adressschalter (x / x) auf der Frontseite. Es können die Adressen bis 99 sowie die Baudraten 96 Bd, 9 Bd, 8 Bd, 576 Bd, 768 Bd und 5 Bd eingestellt werden. Über die frontseitigen Potentiometer ist es möglich, jeweils zwischen Automatik- und manuellem Betrieb umzuschalten. 89999-9. Wichtige Hinweise Konformitätserklärung Das Gerät wurde nach den geltenden Normen geprüft. Die Konformität wurde nachgewiesen. Die Konformitätserklärung ist beim Hersteller BT NETCOM GmbH abrufbar. Hinweise zur Gerätebeschreibung Die Beschreibung enthält Hinweise zum Einsatz und zur Montage des Geräts. Sollten Fragen auftreten, die nicht mit Hilfe dieser Anleitung geklärt werden können, sind weitere Informationen beim Lieferanten oder Hersteller einzuholen. Die angegebenen Vorschriften/ichtlinien zur Installation und Montage gelten für die Bundes republik Deutschland. Beim Einsatz des Geräts im Ausland sind die nationalen Vorschriften in Eigenverantwortung des Anlagenbauers oder des Betreibers einzuhalten. Sicherheitshinweise Für die Montage und den Einsatz des Geräts sind die jeweils gültigen Arbeitsschutz-, Unfall verhütungs- und VDE-Vorschriften einzuhalten. Facharbeiter oder Installateure werden darauf hingewiesen, dass sie sich vor der Installation oder Wartung der Geräte vorschriftsmäßig entladen müssen. Montage- und Installationsarbeiten an den Geräten dürfen grundsätzlich nur durch qualifiziertes Fachpersonal durchgeführt werden, siehe Abschnitt qualifiziertes Fachpersonal. Jede Person, die das Gerät einsetzt, muss die Beschreibungen dieser Anleitung gelesen und verstanden haben. Warnung vor gefährlicher elektrischer Spannung Gefahr bedeutet, dass bei Nicht beachtung Lebensgefahr besteht, schwere Körper verletzungen oder erhebliche Sach schäden auftreten können. Qualifiziertes Fachpersonal Qualifiziertes Fachpersonal im Sinne dieser Anleitung sind Personen, die mit den beschriebenen Geräten vertraut sind und über eine ihrer Tätigkeit entsprechenden Qualifikation verfügen. Hierzu gehören zum Beispiel: Berechtigung zum Anschluss des Geräts gemäß den VDE- Bestimmungen und den örtlichen EVU-Vorschriften sowie Berechtigung zum Ein-, Aus- und Freischalten des Geräts unter Berück sichtigung der innerbetrieblichen Vorschriften; Kenntnis der Unfallverhütungsvorschriften; Kenntnisse über den Einsatz und Gebrauch des Geräts innerhalb des Anlagensystems usw.. Technische Daten BACnet-Schnittstelle Protokoll BACnet MS/TP Übertragungsrate 96... 5 Bd (Werkseinstellung 96 Bd) Verkabelung S85 Zweidrahtbus mit Potentialausgleich in Bus-/Linientopologie Versorgung Betriebsspannungsbereich... 8 V AC/DC (SELV) Stromaufnahme 5 ma (AC) / ma (DC) Einschaltdauer relativ % Ausangsseite Ausgangsspannung x... V DC Ausgangsstrom 5 ma bei V DC Auflösung mv / Digit Gehäuse Abmessungen BxHxT 5 x 7 x 65 mm Gewicht 7 g Einbaulage beliebig Montage Tragschiene TH5 nach IEC 675 Anreihbar ohne Abstand Nach dem Anreihen von 5 Modulen oder einer maximalen Stromaufnahme von A (AC oder DC) pro Anschluss am Netzgerät muss mit der Ver sorgungs spannung neu extern angefahren werden. Material Gehäuse Polyamid 6.6 V Klemmen Polyamid 6.6 V Blende Polycarbonat Schutzart (IEC 659) Gehäuse IP Klemmen IP Anschlussklemmen Versorgung und Bus -polige Anschlussklemme max.,5 mm² eindrähtig max., mm² feinstdrähtig Aderndurchmesser, mm bis max., mm (Anschlussklemme und Brückenstecker als Zubehör in der Verpackung) Geräteanschluss Eingänge max. mm² eindrähtig max.,5 mm² feinstdrähtig Aderndurchmesser, mm bis max.,7 mm Schutzbeschaltung Verpolschutz der Betriebsspannung Verpolschutz von Speisung und Bus Temperaturbereich Betrieb -5 C... +55 C Lagerung - C... +7 C Anzeige Betrieb und Bustätigkeit grüne LED Fehlermeldung rote LED. Prinzipbild A/+ V A /GND BUS B+ BUS A- 5. Anschlussbild V BACnet MS/TP on S-85 Output: Voltage -V ISC - CPU A V AC/DC A A GND A B+ BUS B+ B+ A- BUS A- A-. METZ CONNECT Im Tal 7876 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5-
6. Montage Anlage spannungsfrei schalten Gerät auf Tragschiene (TH5 nach IEC 675, Einbau in Elektroverteiler / Schalttafel) setzen Installation Die Elektroinstallation und der Geräteanschluss dürfen nur durch qualifiziertes Fachpersonal unter Beachtung der VDE- Bestimmungen und örtlicher Vorschriften vorgenommen werden. Anschlussklemme für Busanschluss einstecken. Kabel für Busanschluss anschließen 5 mm eihenmontage 5 6 Das Modul ist ohne Abstand anreihbar. Bei eihenmontage Brückenstecker aufstecken, er verbindet Bus und Versorgungsspannung bei nebeneinander montierten Modulen. Nach dem Anreihen von 5 Modulen oder einer maximalen Stromaufnahme von A (AC oder DC) pro Anschluss am Netzgerät muss mit der Ver sorgungs spannung neu extern angefahren werden. 7. Netzwerkadresse und Bitrate einstellen Schalter zur Konfiguration Hexadezimalschalter x, x definieren die Netzwerkadresse ( - F9; z.b. F9h = 5x6+9 = 9d) und die Baudrate (FA - FF) Schalter x auf E drehen ( Gerät ist als Slave konfiguriert) Schalter x auf A-F drehen, um die Baudrate einzustellen Schalter x auf F drehen und Sekunde warten Die rote und grüne LED blinken, wenn die Baudrate im EEPOM gespeichert wurde Schalter x drehen um die Netzwerkadresse einzustellen Schalter x drehen um die Netzwerkadresse einzustellen Adressschalter x F F F F F F Adressschalter x A B C D E F Bitrate (Bit/s) 96 9 8 576 768 5 Werkseinstellung: 96 Bit/s 8. Softwarebeschreibung Device Object Object_Identifier device, default instance: + Network-Address W-E Object_Name max. 5 Bytes, default BMT-AO_ + Network-Address (Hexadecimal) W-E Object_Type DEVICE (8) System_Status OPEATIONAL () Vendor_Name BT Netcom GmbH Vendor_Identifier Model_Name BMT-AO Firmware_evision. Application_Software_Version. Protocol_Version Protocol_evision Protocol_Services_Supported readproperty, writeproperty, device-communication-control, reinitialize-device, unconfirmed-cov-event-notification, who-has, who-is Protocol_Object_Types_Supported DEVICE, ANALOG_OUTPUT Object_List [5] device, analog-output... Max_APDU_Length_Accepted 6 Segmentation_Supported NO_SEGMENTATION () APDU_Timeout Number_Of_APDU_etries Device_Address_Binding - Database_evision Description BMT_AO Max_Master 7 W-E Max_Info_Frames W-E Analog Output Objects... Object_Identifier analog-output, instance Object_Name Output Output Object_Type ANALOG_OUTPUT () Present_Value..... ( V.... V) W Status_Flags IN_ALAM: FAULT: OVEIDDEN: OUT_OF_SEVICE: / Event_State NOMAL () Out_Of_Service FALSE () / TUE () W Units Percent (98) Priority_Array [6] NULL /..... ( V.... V) elinquish_default..... ( V.... V) W-E esolution.65 (.65 mv) - METZ CONNECT Im Tal 7876 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5-
Fortsetzung Beschreibung der Software Function Table for Analog Output Out_of_ service Potentiometer Priority_ Array Present_Value Analog Output OVE IDDEEN OUT_OF_ SEVICE NULL elinquish_default elinquish_default Value NULL Value NULL elinquish_default unchaged NULL elinquish_default METZ CONNECT Im Tal 7876 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5-
Analog Output Module BMT-AOP 887. Description The BACnet MS/TP module with analog outputs is designed for local switching operations. It is suitable as variable encoder, for example ventilation or mixing valves, valve positions etc. The outputs can be issued by standard object via a BACnet-Client. Addressing of the module and baud rate setting are done with the two address switches (x / x) on the front. Possible settings are addresses to F9 and baud rates 96 Bd, 9 Bd, 8 Bd, 576 Bd, 768 Bd and 5 Bd. With the front-mounted potentiometer, it is possible to switch between automatic mode and manual mode. 89999-9. Declaration of Conformity The device was tested according to the applicable standards. Conformity was proofed. The declaration of conformity is available at the manufacturer BT NETCOM GmbH. Notes egarding Device Description These instructions include indications for use and mounting of the device. In case of questions that cannot be answered with these instructions please consult supplier or manufacturer. The indicated installation directions or rules are applicable to the Federal epublic of Germany. If the device is used in other countries it applies to the equipment installer or the user to meet the national directions. Safety Instructions Keep the applicable directions for industrial safety and prevention of accidents as well as the VDE rules. Technicians and/or installers are informed that they have to electrically discharge themselves as prescribed before installation or maintenance of the devices. Only qualified personnel shall do mounting and installation work with the devices, see section qualified personnel. The information of these instructions have to be read and understood by every person using this device. Symbols Warning of dangerous electrical voltage Danger means that non-observance may cause risk of life, grievous bodily harm or heavy material damage. Qualified Personnel Qualified personnel in the sense of these instructions are persons who are well versed in the use and installation of such devices and whose professional qualification meets the requirements of their work. This includes for example: Qualification to connect the device according to the VDE specifications and the local regulations and a qualification to put this device into operation, to power it down or to activate it by respecting the internal directions. Knowledge of safety rules. Knowledge about application and use of the device within the equipment system etc.. Technical Data BACnet Interface Protocoll BACnet MS/TP Transmission rate 96... 5 Bd (factory setting 96 Bd) Cabling S85 two wire bus with voltage equalizing cable in bus / line topology Supply Operating voltage range... 8 V AC/DC (SELV) Current consumption 5 ma (AC) / ma (DC) elative duty cycle % Output Output voltage x... V DC Output current 5 ma at V DC esolution mv / Digit Housing Dimensions WxHxD. x.8 x.6 in. (5 x 7 x 65 mm) Weight 7 g Mounting position any Mounting standard rail TH5 per IEC 675 Mounting in series the maximum quantity of modules without space connected in line is limited to 5 or to a maximum power consumption of Amps (AC or DC) per connection to the power supply. For any similar block of additional modules a separate connection to the power supply is mandatory. Material Housing Polyamide 6.6 V Terminal blocks Polyamide 6.6 V Cover plate Polycarbonate Type of protection (IEC 659) Housing IP Terminal blocks IP Terminal blocks Supply and bus pole terminal block max. AWG 6 (,5 mm²) solid wire max. AWG 8 (, mm²) stranded wire Wire diameter min.. mm up to max.. mm (terminal block and jumper plug are included to each packing unit) Module connection Input/Output max. AWG (. mm²) solid wire max. AWG (.5 mm²) stranded wire Wire diameter min.. mm up to max.7 mm Protective circuitry polarity reversal protection of operating voltage polarity reversal protection of supply and bus Temperature range Operation -5 C... +55 C Storage - C... +7 C Display Operating / bus activity green LED Error indication red LED. Wiring Diagram A/+ V A /GND BUS B+ BUS A- V BACnet MS/TP on S-85 Output: Voltage -V 5. Connection Diagram ISC - CPU A V AC/DC A A GND A B+ BUS B+ B+ A- BUS A- A-. METZ CONNECT Im Tal 7876 Blumberg Germany Phone +9 77 5- Fax +9 77 5- Distributed by IA CONNECT GmbH and BT NETCOM GmbH Mounting instruction see www.metz-connect.com
6. Mounting Power down the equipment Mount the module on standard rail (TH5 per IEC 675 in junction boxes and/or on distribution panels). Installation Electric installation and device termination shall be done by qualified persons only, by respecting all applicable specifications and regulations. Plug in the terminal block for bus connection Connect the cable for bus supply 5 mm Mounting in series 5 6 The module can be aligned without interspace. Use the jumper plug to connect bus and supply voltage when the modules are mounted in series. The maximum quantity of modules connected in line is limited to 5 or to a maximum power consumption of Amps (AC or DC) per connection to the power supply. For any similar block of additional modules a separate connection to the power supply is mandatory. 7. Network adress and Bit rate setting Configuration Switches Hexadecimal Switches x, x define the Network-Address ( - F9; e.g. F9h = 5x6+9 = 9d) and Baudrate (FA FF). Turn Switch x to E (Device is temporaryly configured as Slave) Turn Switch x to A F to select Baudrate Turn Switch x to F, wait Second ed and green LEDs are blinking when Baudrate ist stored in EEPOM Turn Switch x to select Network-Address Turn Switch x to select Network-Address Adress switch x F F F F F F Adress switch x A B C D E F Bitrate (Bit/s) 96 9 8 576 768 5 Factory setting: 96 Bit/s 8. Softwarebeschreibung Device Object Object_Identifier device, default instance: + Network-Address W-E Object_Name max. 5 Bytes, default BMT-AO_ + Network-Address (Hexadecimal) W-E Object_Type DEVICE (8) System_Status OPEATIONAL () Vendor_Name BT Netcom GmbH Vendor_Identifier Model_Name BMT-AO Firmware_evision. Application_Software_Version. Protocol_Version Protocol_evision Protocol_Services_Supported readproperty, writeproperty, device-communication-control, reinitialize-device, unconfirmed-cov-event-notification, who-has, who-is Protocol_Object_Types_Supported DEVICE, ANALOG_OUTPUT Object_List [5] device, analog-output... Max_APDU_Length_Accepted 6 Segmentation_Supported NO_SEGMENTATION () APDU_Timeout Number_Of_APDU_etries Device_Address_Binding - Database_evision Description BMT_AO Max_Master 7 W-E Max_Info_Frames W-E Analog Output Objects... Object_Identifier analog-output, instance Object_Name Output Output Object_Type ANALOG_OUTPUT () Present_Value..... ( V.... V) W Status_Flags IN_ALAM: FAULT: OVEIDDEN: OUT_OF_SEVICE: / Event_State NOMAL () Out_Of_Service FALSE () / TUE () W Units Percent (98) Priority_Array [6] NULL /..... ( V.... V) elinquish_default..... ( V.... V) W-E esolution.65 (.65 mv) - METZ CONNECT Im Tal 7876 Blumberg Germany Phone +9 77 5- Fax +9 77 5- Distributed by IA CONNECT GmbH and BT NETCOM GmbH Mounting instruction see www.metz-connect.com
Continuation Software Description Function Table for Analog Output Out_of_ service Potentiometer Priority_ Array Present_Value Analog Output OVE IDDEEN OUT_OF_ SEVICE NULL elinquish_default elinquish_default Value NULL Value NULL elinquish_default unchaged NULL elinquish_default METZ CONNECT Im Tal 7876 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5-