Art. Nr. / Order No. 56-1100 MB DNA Extraction Kit Extraction of genomic DNA from swabs, urine and cell culture material Gebrauchsinformation / Instructions for Use Reagenzien für 100 Extraktionen Reagents for 100 extractions FOR PROFESSIONAL USE ONLY! NUR FÜR ERFAHRENE ANWENDER!
Symbole / Symbols Chargen-Nr. / Lot No. Artikel-Nr. / Order No. Verfallsdatum / Expiry date Lagerung bei / Store at Enthält Reagenzien für 100 Bestimmungen Contains reagents for 100 tests Hersteller / Manufacturer
ANWENDUNGSGEBIET Der MB DNA Extraction Kit kann für die Reinigung von genomischer DNA, vorzugsweise von Mikroorganismen, aus Abstrichtupfern, Urin und Zellkulturüberständen und für eine nachfolgende PCR-Analyse angewendet werden. ERKLÄRUNG DES VERFAHRENS Die Zellen werden durch eine Kombination aus Detergenz und chaotropen Salz lysiert. Das Lysat wird direkt auf die Spinsäulen aufgebracht. Die DNA wird selektiv an die hoch spezifische Silikamembran gebunden. Zwei nachfolgende Waschschritte entfernen Reste von Verunreinigungen wie Proteine, Stoffwechselprodukte, Farbstoffe, Detergenz usw. Die gereinigte DNA wird in TE-Puffer eluiert. Der Prozess ist in 30 min abgeschlossen. Die DNA kann direkt in die PCR eingesetzt werden. Reagenz Bezeichnung Spin Columns Collection Tubes Conditioner 100 Extraktionen Art. Nr. 56-1100 100 Einheiten 100 Einheiten 40 ml Ergänzungen Buffer A1 22,9 ml 30,1 ml Ethanol Buffer A2 15,9 ml 37,1 ml Ethanol Buffer E 12 ml ENTHALTENE REAGENZIEN Jedes Kit enthält Reagenzien für die Extraktion von 100 Proben. Das Verfallsdatum der ungeöffneten Packung ist auf dem Außenetikett vermerkt. Die Lagerung erfolgt bis zur Verwendung bei Raumtemperatur. Das chargenspezifische Qualitätskontrollzertifikat (Certificate of Analysis) kann auf unserer Webseite heruntergeladen werden (www.minerva-biolabs.com). BENÖTIGTES, ABER NICHT IM KIT ENTHALTENES MATERIAL Der MB DNA Extraction Kit enthält die Reagenzien für die Extraktion von Gesamt-DNA aus diversen Materialien. Allgemein übliche Verbrauchsmaterialien und Reagenzien eines molekularbiologischen Labors sind nicht enthalten. Dazu zählen: Ethanol > 96 % abs. 1,5 ml Reaktionsgefäße Mikrozentrifuge und Heizblock für 1,5 ml Reaktionsgefäße Pipette mit Filterspitzen (10, 100 und 1000 μl) Für die Extraktion von Sputum wird weiterhin eine NAC-Lösung (100 ml enthalten: 50 ml 2,84 % Natriumcitrat, 50 ml 4 % Natriumhydroxid, 500 mg N-Acteyl-L-cystein) benötigt. last update 03-2011 D E U T S C H 1
PROBENMATERIAL Abstrichtupfer gewinnen in der PCR-basierten klinischen Diagnostik zunehmend an Bedeutung. Abstriche können problemlos und schonend für den Patienten aus dem Rachenraum, der Nase, sekretierenden Hautverletzungen oder dem Vaginalbereich gewonnen werden. Die enthaltene DNA ist bei eingetrockneten Tupfern extrem langlebig und stabil. Für die Lagerung und den Transport müssen bei einer Analyse mit einem PCR- Verfahren keine speziellen Bedingungen eingehalten werden. Tupfer mit Transportmedium lassen sich ebenfalls extrahieren. Der MB DNA Extraction Kit wurde für die effiziente Gewinnung von DNA von allen gängigen Tupfermaterialien entwickelt. Urin, bzw. Poolurin kann üblicherweise auf Grund des hohen Harnstoffgehalts und der notwendigen Lyse der bakteriellen Analyten nicht direkt in die PCR eingesetzt werden. Der MB DNA Extraction Kit ermöglicht die Aufarbeitung von Urin mit einem maximalen Probenvolumen von 200 μl. Es kann sich dabei auch um Sediment oder zentrifugierte Urinproben handeln. Bei hochkonfluenten Zellkulturen oder Medien mit einem Serumgehalt von mehr als 12 % kann es bei der PCR schnell zu Inhibitionen durch Stoffwechselprodukte bzw. Lipide kommen. Phenolrot wird üblicherweise Zellkulturmedien hinzugefügt und beeinflusst mit zunehmender Konzentration in der qpcr die Messung der Fluoreszenz deutlich. In diesen Fällen ist eine Probenvorbereitung durch DNA-Isolierung dringend notwendig. Der Kit wurde nicht für die Aufreinigung von eukaryotischer DNA aus Zellen optimiert. Sputum ist üblicherweise hochviskos und kann nicht direkt für die DNA-Extraktion eingesetzt werden. Für die DNA Extraktion muss das Sputum durch eine chemische Vorbehandlung verflüssigt werden. VORSICHTSMAßNAHMEN Dieser Kit ist ausschließlich für Forschungszwecke bestimmt und darf ohne probenspezifische Validierung nicht für die klinische Diagnostik eingesetzt werden. Dieser Kit sollte nur von geschulten Personen verwendet werden. Das Probenmaterial muss als potentiell infektiös betrachtet und nach den lokalen oder nationalen Vorschriften behandelt werden. Immer Einmalhandschuhe, Laborkittel und Schutzbrille tragen. Bestandteile des Conditioners und des Buffer A1 können mit Bleichmitteln oder säurehaltigen Lösungen hochreaktive Verbindungen bilden. Mischen Sie keine säurehaltigen oder bleichenden Mittel mit dem Flüssigabfall. Ausgelaufene oder verschüttete Reste können mit Wasser und Spülmittel entfernt werden. Risikosätze für den Conditioner und Buffer A1: R 22 Gesundheitsschädlich beim Verschlucken. R 36/38 Reizt die Augen und die Haut. R 52/53 Schädlich für Wasserorganismen, kann in Gewässern längerfristig schädliche Wirkungen haben. Sicherheitssätze: S 13 Von Nahrungsmitteln, Getränken und Futtermitteln fernhalten. S 26 Bei Berührung mit den Augen sofort gründlich mit Wasser abspülen und Arzt konsultieren. S 36 Bei der Arbeit geeignete Schutzkleidung tragen. S 46 Bei Verschlucken sofort ärztlichen Rat einholen und Verpackung oder Etikett vorzeigen. Dieser Kit kann gemäß den örtlichen Bestimmungen entsorgt werden. 2 D E U T S C H last update 03-2011
DURCHFÜHRUNG Aufarbeitung von Tupfern Nasen-, Rachen-oder Vaginalabstriche werden vorzugsweise mit Dacron oder Baumwolltupfern gewonnen. Der Abstrich wird durch festes, ca. 6-10 maliges Reiben an der Läsion auf jeder Seite der Bürste gesammelt. Der gesamte Infektionsbereich sollte abgedeckt werden. Der Tupfer kann für mehr als 1 Jahr gelagert werden, wenn er bei Raumtemperatur für mindestens 2 Stunden getrocknet wurde. Vollständig getrocknete Tupfer können in einem sauberen, DNA-freien Kunststoffbeutel oder Schutzhülle gelagert und transportiert werden. 4. Der Tupfer wird in ein 1,5 ml Reaktionsgefäß gegeben und der Stil mit einer Schere abgeschnitten bzw. bei Tupfern mit Sollbruchstelle abgebrochen. Der Tupfer wird mit 400 μl Conditioner versetzt, das Gefäß verschlossen, intensiv gevortext (10 sec) und der Ansatz über 5 min bei Raumtemperatur (18 bis 25 C) inkubiert. Alternativ kann ein Reaktionsgefäßschüttler über 15 min. verwendet werden. Der Tupfer wird am Gefäßrand ausgedrückt und 350 μl der herausgedrückten Flüssigkeit in ein frisches 1,5 ml Reaktionsgefäß überführt. Der Ansatz wird mit 280 μl absolutem Ethanol versetzt und sofort gut gemischt, um eine Fällung der DNA zu vermeiden. Die Verwendung anderer Alkohole führt zu einer deutlichen Verringerung der Ausbeute an DNA. 5. Der Ansatz wird wie in Kapitel DNA-Isolierung beschrieben weiter bearbeitet. Aufarbeitung von Urin 1 ml Urin werden bei maximaler Geschwindigkeit der Tischzentrifuge (mindestens jedoch 14.000 g) für 15 min zentrifugiert. Der Überstand wird abgekippt oder vorsichtig abgenommen. Das Pellet ist meist nicht sichtbar! Das Pellet wird in 350 μl Conditioner durch kurzzeitiges Vortexen (30 sec) resuspendiert und über 5 min bei Raumtemperatur (18 bis 25 C) inkubiert. Der Ansatz wird mit 280 μl absolutem Ethanol versetzt und sofort gut gemischt, um eine Fällung der DNA zu vermeiden. Die Verwendung anderer Alkohole führt zu einer deutlichen Verringerung der Ausbeute an DNA. 4. Der Ansatz wird wie in Kapitel DNA-Isolierung beschrieben weiter bearbeitet. Aufarbeitung von Zellkulturmaterialien 60 μl des Zellkulturmaterials werden in ein frisches 1,5 ml Reaktionsgefäß überführt. Das Material kann dabei bis zu 10 6 Zellen enthalten. Nach Zugabe von 290 μl Conditioner wird ausgiebig (10 sec.) gevortext und der Ansatz über 5 min bei Raumtemperatur (18 bis 25 C) inkubiert. Der Ansatz wird mit 280 μl absolutem Ethanol versetzt und sofort gut gemischt, um eine Fällung der DNA zu vermeiden. Die Verwendung anderer Alkohole führt zu einer deutlichen Verringerung der Ausbeute an DNA. 4. Der Ansatz wird wie in Kapitel DNA-Isolierung beschrieben weiter bearbeitet. last update 03-2011 D E U T S C H 3
Aufarbeitung von Sputum 4. 5. 1 Volumen Probe wird mit 1 Volumen NAC-Puffer (siehe Kapitel Benötigtes, aber nicht im Kit enthaltenes Material ) durch kurzes Vortexen vermischt. Der Ansatz wird bei Raumtemperatur (18 bis 25 C) unter vorsichtigem Schwenken inkubiert, bis eine handhabbare Fluidität erreicht ist. Die Zellen werden durch Zentrifugation bei maximaler Geschwindigkeit der Tischzentrifuge (mindestens jedoch 14.000 g) für 15 min pelletiert. Der Überstand wird abgekippt oder vorsichtig abgenommen. Das Pellet ist meist nicht sichtbar! Das Pellet wird in 350 μl Conditioner durch kurzzeitiges Vortexen (30 sec) resuspendiert und über 5 min bei Raumtemperatur (18 bis 25 C) inkubiert. Der Ansatz wird mit 280 μl absolutem Ethanol versetzt und sofort gut gemischt, um eine Fällung der DNA zu vermeiden. Die Verwendung anderer Alkohole führt zu einer deutlichen Verringerung der Ausbeute an DNA. 6. Der Ansatz wird wie in Kapitel DNA-Isolierung beschrieben weiter bearbeitet. DNA-Isolierung Buffer A1 und Buffer A2 müssen mit Ethanol abs. (> 96 %) ergänzt werden. Buffer E auf 70 C erwärmen. 4. 5. 6. 7. 8. Für jede Probe wird ein Spin Column wird aus der Verpackung genommen und in das Collection Tube gesteckt. Die Probenkennung wird auf dem Deckel notiert und mit dem gesamten Lysat befüllt, ohne dabei den oberen Rand des Gefäßes zu benetzen. Das Spin Column wird mit dem Collection Tube für 1 min bei 10.600 g (bei Tischzentrifugen ca. 10.000 Umdrehungen/min) zentrifugiert, das Eluat verworfen und das Spin Column wieder in das Collection Tube gesteckt. In das Spin Column werden 500 μl Buffer A1 hineingegeben und das Spin Column mit dem Collection Tube für 1 min bei 10.6000 g (bei Tischzentrifugen ca. 10.000 Umdrehungen/min) zentrifugiert, um den Buffer A1 abzutrennen. Das Eluat wird verworfen und die Säule wieder in das Collection Tube gesteckt. In das Spin Column werden 500 μl Buffer A2 hineingegeben und das Spin Column mit dem Collection Tube für 1 min bei 10.6000 g (bei Tischzentrifugen ca. 10.000 Umdrehungen/min) zentrifugiert, um den Buffer A2 abzutrennen. Das Spin Column wird aus dem Collection Tube genommen und das Eluat (Buffer A2) verworfen. Das Spin Column wird mit dem gleichem Collection Tube noch einmal 1 min bei maximaler Umdrehungsleistung der Zentrifuge zur vollständigen Trocknung zentrifugiert. Das Spin Column wird in ein frisches 1,5 ml Reaktionsgefäß gegeben und das Eluat samt Collection Tube verworfen. Es werden 60 μl Buffer E in das Spin Column pipettiert und für 2 min bei Raumtemperatur inkubiert. Nach der Inkubation wird das System für 2 min bei 10.6000 g (bei Tischzentrifugen ca. 10.000 Umdrehungen/min) zentrifugiert. Das Spin Column wird entfernt und das Probengefäß verschlossen. Der Extrakt kann direkt für die PCR eingesetzt werden. 4 D E U T S C H last update 03-2011
ANMERKUNGEN ZUR TESTDURCHFÜHRUNG Diese Gebrauchsinformation muss für eine erfolgreiche Benutzung des MB DNA Extraction Kit weitgehend verstanden worden sein. Die gelieferten Reagenzien einer Charge sind als integrale Einheit zu verstehen. Reagenzien verschiedener Chargen dürfen nicht vermischt werden. Die Reagenzien des Kits dürfen nach Ablauf der Haltbarkeit nicht mehr verwendet werden. Jegliche Abweichung vom Extraktionsverfahren kann die Resultate beeinträchtigen. Je Ansatz sollte mindestens eine Extraktionskontrolle mitgeführt werden. Vorzugsweise wird diese mit der Internen Amplifikationskontrolle des PCR-Tests versetzt. 4. Der Extrakt ist bei +2 C bis +8 C für ca. 1 Woche stabil und kann bei mindestens -18 C gelagert werden. 5. Die Verwendung anderer Alkohole als Ethanol abs. führt zu einer deutlichen Verringerung der Ausbeute an DNA. 6. Sputum und unbehandelte Zellkulturmaterialien sollten schnellstmöglich extrahiert werden. Zellkulturmaterialien kann durch eine Hitzebehandlung (95 C, 10 min, bis zu 500 μl) für 1 Woche bei Raumtemperatur stabilisiert werden. 7. Die Ausbeute an DNA kann erhöht werden, wenn Buffer E auf 70 C temperiert wird. last update 03-2011 D E U T S C H 5
INDICATION The MB DNA Extraction Kit can be used for the isolation of genomic DNA from swabs, urine, and cell culture supernatants. The kit was especially designed to fit Minerva Biolabs PCR kits and to provide best performance in means of sensitivity and robustness for the detection of microorganisms within the test sample. PRINCIPLE OF THE METHODE Cells are lysed by a combination of detergents and chaotropic salt. The lysate is directly applied onto the spin columns. The DNA is selectively bound to the highly specified silica membrane. Two subsequent washes remove residual contaminants, like proteins, metabolites, dyes, detergent etc. The purified DNA is eluted in TE buffer. The procedure is completed in 30 min. The DNA is ready-to-use for PCR. REAGENTS Each kit contains reagents for 100 extractions. The expiry date of the unopened package is marked on the package label. The kit components are stored until use at room temperature (18 to 25 C). The lot specific quality control certificate (Certificate of Analysis) can be downloaded from our website (www.minerva-biolabs.com). Kit Component Label Information Spin Columns 100 extractions Order No. 56-1100 100 units Required Supplements Collection Tubes 100 units Conditioner 40 ml Buffer A1 29 ml 30.1 ml Ethanol Buffer A2 15.9 ml 37.1 ml Ethanol Buffer E 12 ml NEEDED, BUT NOT INCLUDED IN THE KIT The MB DNA Extraction Kit contains the reagents for the extraction of genomic DNA from various sample materials. General industrial supplies and reagents, usually available in a molecular biology laboratory are not included: Ethanol > 96 % abs. Micro centrifuge tubes (5 ml) Micro centrifuge and heat block for 5 ml reaction tubes micropipettes and filtered tips (10, 100, and 1000 μl) The extraction of sputum samples requires a NAC solution (100 ml contain: 50 ml 84 % sodium citrate, 50 ml 4 % sodium hydroxide, 500 mg N-acteyle-L-cysteine). 6 E N G L I S H last update 03-2011
SPECIMEN The collection of DNA specimen for diagnostic purposes with swabs is convenient and non-invasive. Swabs are easy-to-use and usually at hand for sampling buccal, nasal, pharyngeal, ichors and vaginal samples. No special storage or shipping conditions are required for subsequent PCR analysis. Urine and pooled urine usually can not be tested directly by PCR due to inhibiting level of urea and required lysis of the bacterial load. MB DNA Extraction Kit allows the preparation of a maximum volume of 200 μl urine per sample, including centrifuged and resuspended samples. PCR inhibiting substances may accumulate in the medium of older cultures or medium containing more than 12 % fetal calf serum. Phenol red usually contained in the cell culture medium can inhibit or cross react with the optical reading of the fluorescence signal in qpcr. MB DNA Extraction Kit is able to lyse bacteria present in the cell culture material and allows isolation from inhibitors for PCR. Preparation of eukaryotic DNA from cells is not within the scope of the kit. Sputum are usually characterized by a high viscosity and cannot lysed and directly applied on a silica membrane for extraction. Anyhow, as this type of sample is common in bronchial disease detection a special pretreatment is required to increase the fluidity of the sample. PRECAUTIONS MB DNA Extraction Kit is intended for research use only. Not for clinical diagnostics or testing of human samples without extensive validation. This kit should be used only by trained persons. All samples should be considered potentially infectious and handled according to local or national regulations. This kit substances may be disposed of according to local regulations. Always wear a suitable lab coat, disposable gloves, and protective goggles. The sample-preparation waste contains Conditioner and Buffer A1, which can form highly reactive compounds when combined with bleach. DO NOT add bleach or acidic solutions directly to the sample-preparation waste. If liquid containing these buffers is spilt, clean with suitable laboratory detergent and water. The risk phrases applying to Conditioner and Buffer A1 are: R 22 Harmful if swallowed. R 36/38 Irritating to eyes and skin. R 52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. The risk and safety phrases applying are: S 13 Keep away from food, drink and animal feed. S 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S 36 Wear suitable protective clothing. S 46 If swallowed, seek medical advice immediately and show container or label. last update 03-2011 7 E N G L I S H
PROCEDURE Preparation of Swab Samples Collect buccal, nasal, pharyngeal, ichors or vaginal swabs with DACRON or cotton materials. The swab sample is collected by rubbing it firmly approximately 6-10 times at the lesion on each side of the brush. The entire spot must be covered. The swab can be stored for more than 1 year if dried at room temperature for at least 2 hours. When completely dry, contain the swab in a clean, DNA-free bag or tube usually coming with the swab. 4. Place the swab into a capped 5 ml micro centrifuge tube (not provided with the kit) by either cutting of the handle with scissors or by breaking it at the break point. The swab should fit entirely inside the tube allowing the cap to close. Add 400 μl of Conditioner to the swab, vortex intensively (10 sec) and incubate at room temperature (18 to 25 C) for 5 min. Alternatively, a tube shaker can be used for 15 min. Squeeze the swab at the inner wall of the tube and transfer 350 μl of the sample into a fresh 5 ml micro centrifuge tube. Add 280 μl of absolute ethanol to the mixture. Vortex immediately and very thoroughly in order to prevent any precipitation of nucleic acids. 5. Proceed as described in chapter DNA Isolation. Preparation of Urine Samples Centrifuge 1 ml of urine at maximum speed of the desk centrifuge (at least 14.000 x g) for at least 15 min. Carefully discard the supernatant. Please note, that a pellet is usually not visible. Resuspend the pellet in 350 μl Conditioner, resuspend by vigorous vortexing (at least 30 sec) and incubate at room temperature (18 to 25 C) for at least 5 min. Add 280 μl of absolute ethanol to the mixture. Vortex immediately and very thoroughly in order to prevent any precipitation of nucleic acids. 4. Proceed as described in chapter DNA Isolation. Preparation of Cell Culture Material Transfer 60 μl of cell culture material into a fresh 5 ml reaction tube. The material can contain up to 10 6 cells. Add 290 μl of Conditioner, vortex for at least 10 sec and incubate at room temperature (18 to 25 C) for at least 5 min. Add 280 μl of absolute ethanol to the mixture. Vortex immediately and very thoroughly in order to prevent any precipitation of nucleic acids. 4. Proceed as described in chapter DNA Isolation. 8 E N G L I S H last update 03-2011
Preparation of Sputum Samples 4. 5. Add 1 volume sample to 1 volume NAC buffer (ref. Chapter Needed, but not included in the kit ). Vortex briefly. Incubate while agitating gently at room temperature (18 to 25 C), until the sample has attained the desired fluidity. Pellet the cells by centrifugation at maximum speed of the desk centrifuge (at least 14.000 g) for 15 min. Discard the supernatant and the keep the possibly none-visible pellet. Reconstitute the pellet in 350 μl Conditioner by briefly vortexing (30 sec) and incubation at room temperature (18 bis 25 C) for 5 min. Add 280 μl of absolute ethanol, mix immediately and vigorously to avoid precipitation of DNA. The use of other alcohols then ethanol decreases the yield of DNA drastically. 6. Proceed as described in chapter DNA Isolation. DNA Isolation Reconstitute Buffer A1 and Buffer A2 with absolute ethanol as stated on the bottle label. Pre-heat Buffer E to 70 C. 4. Take one spin column per sample from the kit and stick it into a collection tube. Mark the sample identification on the lid of the spin column. Fill the sample lysate into the spin column without moistening the rim of the spin column. Centrifuge the system for 1 min at 10,600 x g (approx. 10,000 rpm with a desk centrifuge). Discard the flow through from the collection tube and reassemble the spin column and the collection tube. Add 500 μl of Buffer A Centrifuge the system for 1 min at 10,600 x g (approx. 10,000 rpm with a desk centrifuge), discard the flow through and re-assemble the spin column. Fill the spin column with 500 μl Buffer A Centrifuge the system for 1 min at 10,600 rpm (10,000 x g), take the spin column out of the collection tube, dump the containing Buffer A2, discard the flow through and re-assemble the spin column. 5. Centrifuge for 1 min at full speed (approx. 13,200 rpm) in order to remove the remaining Buffer A 6. 7. Discard the collection tube containing the Buffer A2 and place the spin column into a sample storage tube. Pipette 60 μl of pre-heated Buffer E (70 C) into the spin column directly onto the center of the silica membrane. The complete membrane should get in touch with the Buffer E. Secure the sample storage tube and incubate for 2 min at room temperature. 8. Following the incubation, centrifuge the system for 2 min at 10,600 rpm (10,000 x g). 9. Remove the spin column and use the eluate directly for the PCR procedure. last update 03-2011 E N G L I S H 9
NOTES ON THE PROCEDURE This leaflet must be widely understood for a successful use of MB DNA Extraction Kit. The reagents supplied should not be mixed with reagents from different lots and used as an integral unit. The reagents of the kit should not be used beyond its shelf life. Any deviation from the extraction method can affect the results. For each setup, the use of control samples is advised to secure the day-to-day validity of results. at The spike with an Internal Amplification Control facilitate the evaluation of the extraction. 4. Do not use other alcohols than ethanol, because other alcohols may cause inconsistent yields. 5. Pre-heating of Buffer E increases the yield drastically. 6. The extract is stable for approximately 1 week at +2 C to +8 C and can be kept at -18 C for long term storage. 7. Sputum and untreated cell culture materials should be extracted as soon as possible. Cell culture materials can be stabilized by heat treatment (95 C, 10 min, up to 500 μl) for 1 week at room temperature. APPENDIX Limited Product Warranty This warranty limits our liability for replacement of this product. No warranties of any kind, express or implied, including, without limitation, implied warranties of merchantability or fitness for a particular purpose, are provided. Minerva Biolabs shall have no liability for any direct, indirect, consequential, or incidental damages arising out of the use, the results of use, or the inability to use this product. 10 E N G L I S H last update 03-2011
Leerseite Blank page last update 03-2011 11
Related Products MB Taq DNA Polymerase 53-0050/-0100/-0200/-0250 MB Taq DNA Polymerase (5 U/μl) 50/100/200/250 units 53-1050/-1100/-1200/-1250 MB Taq DNA Polymerase (1 U/μl) 50/100/200/250 units Diagnostic Kits for conventional PCR 11-1025/-1050/-1100/-1250 Venor GeM Mycoplasma Detection Kit 25/50/100/250 tests 11-7024/-7048/-7096/-7240 Venor GeM Advance Mycoplasma Detection Kit 24/48/96/240 tests 12-1025/-1050/-1100/-1250 Onar EUB Eubacteria Detection Kit 25/50/100/250 tests Diagnostic Kits for qpcr 11-4025/100/250 Venor GeM-qEP Mycoplasma ssp. Detection Kit 25/100/250 tests Mycoplasma Eliminiation 10-0200/0500/1000 Mynox Mycoplasma Elimination Reagent 2/5/10 treatments 10-0201/0501/1001 Mynox Gold Mycoplasma Elimination Reagent 2/5/10 treatments Clinical Diagnostic Kits for qpcr 20-2025/-2100/-2250 Onar Mp Mycoplasma pneumoniae 25/100/250 tests 21-2025/-2100/-2250 Onar Ls Legionella species 25/100/250 tests 21-3025/-3100/-3250 Onar Lp Legionella pneumophila 25/100/250 tests 22-2025/-2100/-2250 Onar MRSA Methicillin-resistant S. aureus 25/100/250 tests 23-2025/-2100 Onar Syphilis Treponema pallidum 25/100 tests 24-2025/-2100/-2250 Onar Ct Chlamydia trachomatis 25/100/250 tests 25-2025/-2100/-2250 Onar Pertussis Bordetella pertussis/parapertussis 25/100/250 tests Quantification Standards, 100 μl each, 1x10 6 genomes/μl 52-0116 Acholeplasma laidlawii 52-0129 Mycoplasma arginini 52-0117 Mycoplasma fermentans 52-0130 Mycoplasma hyorhinis 52-0112 Mycoplasma orale 52-0119 Mycoplasma pneumoniae 52-0124 Mycoplasma synoviae 52-0164 Spiroplasma citri Genomic DNA Extracts, 100 μl each, +/ 10 ng / 100 μl (selection) 51-0177 Ureaplasma urealyticum, NC 10177 51-0111 Mycoplasma hominis, NC 010111 51-0112 Mycoplasma orale, NC 010112 51-0117 Mycoplasma fermentans PG19, NC 010117 51-0119 Mycoplasma pneumoniae, NC 010119 51-0129 Mycoplasma arginini, NC 010129 51-0162 Mycoplasma arthritidis, NC 010162 51-0195 Mycoplasma genitalium, NC 010195 51-1746 Mycoplasma penetrans, NC 11746 DNA Remover TM 15-2025 DNA Decontamination Reagent, spray bottle 250 ml 15-2200 DNA Decontamination Reagent, refill bottles 4 x 500 ml Mycoplasma Off 15-1000 Surface Disinfectant Spray, spray bottle 1000 ml 15-5000 Surface Disinfectant Spray, refill bottles 5 x 1000 ml Mycoplasma Off -Wipes 15-1001 Surface disinfectant Wipes in dispenser box 120 wipes 15-5001 Surface Disinfectant Wipes, refill pack 5 x 120 wipes ZellShield TM 13-0050/-0150 Contamination Prevention Reagent 100x concentrate 1000 ml/ 5 x 1000 ml PCR Ultra Pure Water 55-0015/-0075 PCR Grade Water for all PCRs and qpcrs, 5 ml/ 5 x 5 ml cdna synthesis sequencing and cycle sequencing
Manufacturer Minerva Biolabs GmbH Koepenicker Str. 325 D-12555 Berlin Germany Ordering Tel. +49 (0)30 2000 437-0 Fax +49 (0)30 2000 437-9 order@minerva-biolabs.com Product Information www.minerva-biolabs.com info@minerva-biolabs.com Technical Service Tel. +49 (0)30 2000 437-0 support@minerva-biolabs.com Made in Germany Minerva Biolabs GmbH develops and manufactures products in accordance with EN ISO 9001:2008 and EN ISO 13485:2003 quality system requirement. Reg.No. SY 60026567 0001 & SX 60025009 0001...as precise as diagnostics should be TM