GPS-Warner Avertisseur GPS GPS-Locator Schnellstartanleitung - Guide de démarrage rapide Installation Guide Deutsch - Français - English
GPS-Warner Avertisseur GPS GPS-Locator Schnellstartanleitung - Guide de démarrage rapide Installation Guide Deutsch: Seiten 4-20 Français: pages 22-37 English: pages 38-46 05/2009 - JG//HS//SF
GPS-WARNER Schnellstartanleitung Deutsch
Installation und Registrierung... 6 1. Schritt...6 2. Schritt...6 3. Schritt...13 4. Schritt...14 Tipps & Hinweise... 15 LED-Belegung am Gerät...15 Support... 19 1. Online...19 2. E-Mail...19 3. Telefon...19 Inhaltsverzeichnis Deutsch 5
Installation und Registrierung ACHTUNG: Schliessen Sie den POI PILOT 3000 GPS-Warner erst nach Installation der erforderlichen Treiber an den PC an! Schnellstartanleitung So installieren Sie die Software für den POI PILOT 3000 GPS-Warner in nur wenigen Schritten auf Ihrem PC: 1. Schritt: Legen Sie die im Lieferumfang enthaltene CD in ein entsprechendes Laufwerk an Ihrem PC ein. Die Installation startet dann automatisch. Sollte dies nicht der Fall sein, so starten Sie die Installation mittels der Datei Setup.exe von der CD. Abb. 1: Installationsstart Folgen Sie den weiteren Installationsschritten um das Programm und die notwendigen Treiber auf Ihrem PC zu installieren. 2. Schritt: Treiberinstallation Während der Installation der POIbase Software wird ein Treiber für den POI Pilot 3000 installiert. Die Installationsanweisungen für den Treiber erfolgen leider nur in Englisch. Um sicher zu stellen, dass Sie die Treiber richtig installieren führen Sie die folgenden Schritte bitte sorgfältig durch. 6 Deutsch
Als erstes erscheint ein Dialogfenster zur Installation des Treibers. Abb. 2: Willkommensbildschirm Um mit der Installation fortzufahren, wählen Sie bitte den Punkt I accept the terms of the license agreement. Die Schaltfläche Next kann dann betätigt werden, um zum nächsten Schritt zu gelangen. Schnellstartanleitung Abb. 3: Lizenzbedingungen Im nächsten Schritt können Sie ein Installationsverzeichnis für den Treiber auswählen. Falls Sie diesen nicht ändern möchten und auf den Deutsch 7
Standardeinstellungen belassen wollen, so können Sie gleich mit Next fortfahren. Wenn Sie ein anderes Installationsverzeichnis auswählen möchten, so klicken Sie mit der linken Maustaste auf Browse und wählen dann das gewünschte Verzeichnis aus. Schnellstartanleitung Abb. 4: Installationspfad Starten Sie im nächsten Fenster die Installation des Treibers mit der Schaltfläche Install. Die Treiber werden nun auf Ihre Festplatte kopiert. Abb. 5: Beginn der Installation 8 Deutsch
Nachdem der Kopiervorgang abgeschlossen ist, bestätigt Ihnen das neue Dialogfenster die erfolgreiche Installation. Entfernen Sie den Haken, bevor Sie auf Finish klicken! Sie können nun Ihren POI PILOT 3000 GPS Warner mit dem PC verbinden. Anmerkung: Sollten Sie dieses Fenster nicht sehen, so überprüfen Sie bitte ob das Installations-Fenster eventuell im Hintergrund liegt. Abb. 6: Abschluss der Installation ACHTUNG: Verbinden Sie jetzt mittels des beiliegenden USB-Kabels den POI PILOT 3000 GPS-Warner mit dem PC und stellen Sie den Schalter am Gerät auf USB! Schnellstartanleitung Starten Sie noch nicht die POIbase Software! Wenn Sie Ihren POI PILOT 3000 GPS-Warner zum ersten Mal mit dem PC verbinden, wird Ihr Computer nach einer neuen Hardware suchen. Deutsch 9
Unter Windows XP folgen Sie bitte den nachfolgenden Schritten, bei Windows Vista erfolgt die Installation vollautomatisch. Schnellstartanleitung Abb. 7: Erkennung der neuen Hardware Wählen Sie im Assistenten für das Suchen nach neuer Hardware bitte die Option Ja, nur dieses eine Mal aus und betätigen dann den Weiter - Button. Lassen Sie im darauffolgendem Dialogfenster die Auswahl auf Software automatisch installieren (empfohlen) bestehen und setzen Sie die Installation mit Weiter fort. Abb. 8: Automatische Installation 10 Deutsch
Ihr Computer wird nun nach einem geeigneten Treiber für die Hardware suchen. Dies kann einige Zeit in Anspruch nehmen. Brechen Sie daher bitte die Suche nach dem geeigneten Treiber für die neue Hardware auf keinen Fall ab. Warten Sie bis Ihnen der Assistent meldet, dass die Installation erfolgreich abgeschlossen ist und Sie können diese mit Fertig stellen beenden. (siehe Abb. 9) Abb. 9: Fertigstellung der Suche nach neuer Hardware Nach Abschluss dieser Treiberinstallation folgt ein weiteres Dialog-Fenster für einen weiteren Treiber, der noch benötigt wird. Schnellstartanleitung Abb. 10: Installation des zweiten Treibers Deutsch 11
Wählen Sie auch hier bitte die Option Ja, nur dieses eine Mal aus und bestätigen Sie die Auswahl mit Weiter. Im darauffolgendem Dialogfenster lassen Sie die Auswahl ebenfalls wieder auf Software automatisch installieren (empfohlen) bestehen und setzen Sie die Installation mit Weiter fort. Schnellstartanleitung Abb. 11: Automatische Suche nach zweitem Treiber Ihr Computer wird nun wieder nach einem geeigneten Treiber für die neue Hardware suchen. Brechen Sie die Suche bitte nicht ab, sondern warten Sie wieder bis das Dialogfenster erscheint, dass die Installation abgeschlossen ist (siehe Abb. 12). Abb. 12: Erfolgreiche Installation des zweiten Treibers. 12 Deutsch
Die Installation der Treiber für den POI PILOT 3000 GPS-Warner ist nun vollständig abgeschlossen und Sie können die POIbase Software starten. 3. Schritt: Falls die POIbase Software nach der Installation nicht automatisch geöffnet wurde, so können Sie diese über Start -> Alle Programme -> POIbase POI PILOT 3000 -> POI PILOT 3000 GPS-Warner starten. Nach dem Start der POIbase Software wird diese das Gerät nun automatisch erkennen und Sie auf den Anmeldebildschirm weiterleiten. Abb. 13: Anmeldebildschirm Schnellstartanleitung Deutsch 13
4. Schritt: Führen Sie im Anschluss nun die Registrierung durch. Betätigen Sie dazu die Schaltfläche Registrieren und es öffnet sich das entsprechende Registrierungsfenster. Schnellstartanleitung Abb. 14: Registrierung Tragen Sie in die entsprechenden Pflichtfelder bitte die notwendigen Daten ein und achten Sie darauf, dass eine gültige E-Mailadresse (da Sie über diese eine Bestätigung von uns erhalten) angegeben wird. Die Registrierung ist nur einmal notwendig. Der Aktivierungscode, den Sie zur Registrierung benötigen, befindet sich auf der Vorderseite der CD-Rom aufgedruckt. Sobald die Registrierung abgeschlossen ist, können Sie sich mit Ihrer E-Mailadresse und Ihrem Passwort anmelden und die POI- Auswahl beginnen. Weitere Informationen zur Bedienung der Software finden Sie in der PDF- Bedienungsanleitung in der Programmgruppe POIbase POI PILOT 3000 auf Ihrem PC. 14 Deutsch
Tipps & Hinweise LED-Belegung am Gerät Linke LED Grün aus Grün an Orange blinkend Orange an Rechte LED Rot blinkend Blau blinkend Rot/Blau blinkend Akku im Gerät vollständig aufgeladen Akku im Gerät wird aufgeladen GPS-Empfänger arbeitet GPS-Empfänger sucht Satelliten Diese LEDs dienen zur Unterscheidung der Warnung, z.b. von einem stationären zu einer mobilen Blitzerstelle. Weitere Informationen zur Bedeutung der LEDs finden Sie in der PDF-Bedienungsanleitung in der Programmgruppe POIbase POI PILOT 3000 auf Ihrem PC. Schnellstartanleitung Deutsch 15
Sollten Sie sich nicht sicher sein, ob die Installation erfolgreich abgeschlossen worden ist, so können Sie dies wie folgt überprüfen: Rufen Sie den Geräte-Manager Ihres Computers auf. Schnellstartanleitung Windows XP: Start Systemsteuerung System Hardware Gerätemanger Windows Vista: Systemsteuerung Gerätemanager Im Geräte-Manager Ihres Computer sind sämtliche angeschlossenen Geräte aufgelistet. Wenn der POI PILOT 3000 GPS-Warner mit dem PC verbunden ist und die Treiber richtig installiert worden sind, so sollten Sie unter Anschlüsse (COM und LPT) die Hardware CP210x USB to UART Bridge Controller finden können. (s. Abb. 16) Wenn der POI PILOT 3000 GPS-Warner nicht mit dem PC verbunden ist, so ist dieser Eintrag nicht vorhanden. Abb. 15: Geräte-Manager bei verbundenem POI PILOT 3000 16 Deutsch
Um die Treiber und die POIbase Software wieder zu deinstallieren, gehen Sie bitte wie folgt vor: Rufen Sie die Systemsteuerung auf und öffnen Sie mit einem Doppelklick auf Software Ihre auf dem PC installierten Programme auf. Suchen Sie dort nach dem Eintrag POI PILOT 3000 GPS-Warner und deinstallieren Sie die Software mit einem Klick auf Entfernen. Nach dem dies abgeschlossen ist, suchen Sie nach dem Eintrag Silicon Laboratories CP210x VCP Drivers for Windows 2000/XP/2003 Server/Vista und deinstallieren Sie diesen ebenfalls mit Entfernen. Nur bei Windows XP: Zu letzt suchen Sie den Eintrag CP210x USB to UART Bridge aus der Liste raus und entfernen diesen ebenfalls von Ihrem Rechner. Neuinstallation ohne vorherige Deinstallation Falls Sie die POIbase Software einmal neu installieren müssen und die Treiber nicht vorher deinstalliert haben, so werden Sie während der Neuinstallation gefragt, ob Sie den Treiber neu installieren möchten oder die bestehende Installation aktualisieren möchten. Wählen Sie in diesem Fall, im Dialogfenster (s. Abb. 16) bitte die Option Cancel aus. Der vorherige Treiber bleibt somit installiert und Sie brauchen diesen nicht erneut zu installieren. Schnellstartanleitung Deutsch 17
Schnellstartanleitung Abb. 16: Treiber bereits vorhanden 18 Deutsch
Support 1. Online In unserem Online-Supportbereich erhalten Sie: kostenlose Updates für viele POICON-Produkte viele Tipps und wichtige Informationen zu Ihrem Produkt www.poicon.com -> Service + Support 2. E-Mail Bei Fragen oder Anregungen stehen wir Ihnen kostenfrei per E-Mail unter support@poicon.com zur Verfügung. 3. Telefon Bestellannahme: Bestellungen, Produktanregungen, Fragen zu weiteren Produkten oder Contentdiensten Aus Deutschland: 01805-764 266 * Aus dem Ausland: +49 1805-764 266 * Schnellstartanleitung Technischer Kundendienst: Hier erhalten Sie Hilfe bei der Installation und individuelle Unterstützung bei Anwendungsproblemen Aus Deutschland: 0900-1764266 ** Aus dem Ausland: +49-900-1764266 ** Deutsch 19
Viel Freude mit Ihrem neuen POIPilot Ihr POICON Team Hamburg Schnellstartanleitung * Für diesen Service fallen aus dem Festnetz der T-Com Kosten in Höhe von 0,14 Euro pro Minute an. Die Preise können für Anrufe aus dem Mobilfunknetz und dem Ausland abweichen. ** Für diesen Service fallen aus dem Festnetz der T-Com Kosten in Höhe von 0,49 Euro pro Minute an. Die Preise knnen für Anrufe aus dem Mobilfunknetz und dem Ausland abweichen. 20 Deutsch
Avertisseur GPS guide de démarrage rapide Français
Installation et inscription... 24 Etape 1... 24 Etape 2... 24 Etape 3...31 Etape 4... 32 Astuces et consignes... 33 Indicateurs LED... 33 Support... 36 1. Par Internet... 36 2. Par E-Mail... 36 3. Par Téléphone... 36 Sommaire Français 23
Installation et inscription ATTENTION: Branchez l avertisseur GPS uniquement après avoir terminé l installation du logiciel sur le PC! Guide de démarrage rapide Voici comment installer le logiciel pour l avertisseur GPS POI PILOT sur votre PC: Etape 1: Insérez le CD fourni dans un lecteur de votre PC. L installation démarre alors automatiquement. Sinon, exécutez le fichier setup.exe présent sur le CD. Img. 1: Démarrer l installation Suivez l assistant d installation pour installer le logiciel et les pilotes sur votre PC. Etape 2: Installation des pilotes L installation du logiciel POIbase contient aussi les pilotes du POI Pilot 3000. Les consignes d installation sont en anglais. Afin de bien installer le pilote, suivez attentivement les étapes suivantes. 24 Français
Une première fenêtre signale l installation du pilote. Img. 2: Ecran d accueil Pour continuer l installation, cochez I accept the terms of the license agreement. Cliquez ensuite sur Next. Guide de démarrage rapide Img. 3: Licence Français 25
Vous pouvez maintenant choisir le dossier d installation du pilote. Si vous souhaitez laisser le dossier proposé, cliquez sur Next. Pour choisir un autre dossier, faites un clic sur le bouton Browse puis choisissez l emplacement voulu. Guide de démarrage rapide Img. 4: Chemin d installation Dans la fenêtre suivante, démarrez l installation du pilote avec le bouton Install. Les pilotes sont alors copiés sur le disque dur. Img. 5: Installation en cours 26 Français
Une fois la copie terminée, une fenêtre confirme le succès de l installation. Décochez la case avant de cliquer sur Finish! Vous pouvez maintenant brancher le POI PILOT 3000 Avertisseur GPS à votre PC. Remarque: Si vous ne voyez pas cette fenêtre, veuillez vérifier que la fenêtre d installation ne soit pas cachée en arrière-plan. Img. 6: Fin de l installation ATTENTION: Branchez maintenant POI PILOT 3000 Avertisseur GPS à l aide du câble USB fourni et placez l interrupteur de l appareil en position USB! Ne démarrez pas encore le logiciel POIbase! Guide de démarrage rapide Votre ordinateur recherche le nouveau matériel quand vous branchez votre POI PILOT 3000 Avertisseur GPS au PC pour la première fois. Français 27
Sur Windows XP, veuillez suivre les étapes suivantes. Sur Windows Vista, l installation se fait automatiquement. Guide de démarrage rapide Img. 7: Détection du nouveau matériel Dans la fenêtre de l assistant de détection de nouveau matériel, cochez la case Oui, cette fois seulement puis cliquez sur Suivant. Dans la fenêtre suivante laissez cochée la case Installer automatiquement le logiciel (recommandé) puis continuez l installation avec Suivant. Img. 8: Installation automatique 28 Français
L ordinateur cherche les pilotes du matériel. Ceci peut durer quelques secondes. Ne pas interrompre la recherche en cours. Attendez que l assistant signale que l installation a été effectuée avec succès puis finalisez avec Terminer (voir Img. 9). Img. 9: Fin de la recherche du nouveau matériel Une fois l installation du pilote terminée, une nouvelle fenêtre signale l installation d un pilote supplémentaire. Guide de démarrage rapide Img. 10: Installation du second pilote Français 29
Dans la fenêtre de l assistant de détection de nouveau matériel, cochez la case Oui, cette fois seulement puis cliquez sur Suivant. Dans la fenêtre suivante laissez cochée la case Installer automatiquement le logiciel (recommandé) puis continuez l installation avec Suivant. Guide de démarrage rapide Img. 11: Recherche automatique du second pilote L ordinateur cherche les pilotes du matériel. Ne pas interrompre la recherche en cours. Attendez que l assistant signale que l installation a été effectuée avec succès. (voir Img. 12) Img. 12: Installation du second pilote avec succès. 30 Français
L installation du pilote du POI PILOT 3000 Avertisseur GPS est maintenant terminée et vous pouvez démarrer le logiciel POIbase. Etape 3: Si le logiciel POIbase ne s est pas ouvert automatiquement après l installation, ouvrez-le via Démarrer -> Tous les programmes -> POIbase POI PILOT 3000 -> POI PILOT 3000 Avertisseur GPS. Une fois le logiciel POIbase démarré, il reconnaît l appareil automatiquement et ouvre l écran d inscription. Img. 13: Ecran d inscription Guide de démarrage rapide Français 31
Etape 4: Effectuez l inscription. Confirmez avec le bouton Enregistrer pour ouvrir la fenêtre correspondante. Guide de démarrage rapide Img. 14: Inscription Remplissez les différentes cases et saisissez une adresse E-Mail valide (car vous recevrez une confirmation à cette adresse). L inscription n est à faire qu une fois. Le code d activation requis pour l inscription se trouve à l avant du CD-Rom. Une fois l inscription terminée, vous pouvez ouvrir votre compte à l aide de l adresse E-Mail et du mot de passe puis vous pouvez choisir les POI. Vous trouverez plus d informations concernant l utilisation du logiciel dans le mode d emploi disponible sur votre PC en PDF dans la liste des programmes POIbase POI PILOT 3000. 32 Français
Astuces et consignes Indicateurs LED LED gauche Vert éteint Vert allumé Orange clignotant Orange allumé LED droite Rouge clignotant Bleu clignotant Rouge/Bleu clignotant Batterie chargée Batterie en chargement Récepteur GPS en marche Récepteur GPS recherche satellites Ces LEDs servent à vous avertir, p. ex. d un radar fixe ou mobile. Trouvez toutes les informations sur la signification des LEDs dans le mode d emploi disponible en PDF sur votre PC dans la liste des programmes POIbase POI PILOT 3000. Guide de démarrage rapide Français 33
Vous pouvez vérifier le succès de l installation ainsi: Ouvrez le gestionnaire de périphérique de votre ordinateur. Guide de démarrage rapide Windows XP: Démarrer Panneau de configuration Système Matériel Gestionnaire de périphérique Windows Vista: Panneau de configuration Gestionnaire de périphériques Le Gestionnaire de périphériques de votre ordinateur liste plusieurs appareils. Quand POI PILOT 3000 Avertisseur GPS est branché à votre PC et que les pilotes sont bien installés, allez dans Ports (COM et LPT) pour voir le matériel CP210x USB to UART Bridge Controller (voir Img. 15). Si le POI PILOT 3000 Avertisseur GPS n est pas branché au PC ce matériel n apparaît pas dans la liste. Img. 15: Gestionnaire de périphériques avec POI PILOT 3000 branché 34 Français
Voici comment désinstaller le pilote et le logiciel POIbase: Ouvrez le panneau de configuration puis Ajout/Suppression de programmes. Cherchez la ligne POI PILOT 3000 GPS-Warner et désinstallez le logiciel en cliquant sur le bouton Désinstaller Une fois le premier logiciel désinstallé, cherchez la ligne Silicon Laboratories CP210x VCP Drivers for Windows 2000/XP/2003 Server/Vista et désinstallez-le également avec le bouton Désinstaller. Sur Windows XP seulement: Cherchez la ligne CP210x USB to UART Bridge puis désinstallez-le. Réinstallation sans désinstallation Note: Si vous devez réinstaller le logiciel POIbase sans désinstaller les pilotes, un message vous demande si vous voulez réinstaller les pilotes ou actualiser l installation actuelle. Dans ce cas, cochez la case Cancel (voir Img. 14). Ceci permet de conserver le pilote précédent car il n est pas nécessaire de le réinstaller. Guide de démarrage rapide Img. 16: Pilote déjà présent Français 35
Support 1. Par Internet Notre support en ligne: Guide de démarrage rapide des mises à jour gratuites de nombreux produits POICON des astuces pour optimiser votre produit www.poicon.com -> Service + Support 2. Par E-Mail Envoyez un E-Mail à support@poicon.com 3. Par Téléphone Commande: Commandes et renseignements Depuis l Allemagne: 01805-764 266 * Depuis la France ou ailleurs: +49 1805-764 266 * Support technique: Obtenez de l aide pour l installation et la résolution individualisée des éventuels incidents Depuis l Allemagne: 0900-1764266 ** Depuis la France ou ailleurs: +49-900-1764266 ** 36 Français
Nous vous remercions de votre confiance en POIPilot L équipe POICON Hambourg Guide de démarrage rapide * Le coût de l appel dépend de votre opérateur téléphonique. ** Numéro surtaxé. Le coût de l appel dépend de votre opérateur téléphonique. Français 37
GPS Locator Installation guide English
Installation and Registration... 40 Step 1... 40 Step 2... 40 Step 3...42 Step 4...42 Tipps & Information... 43 LEDs on the decvice... 43 Support... 46 1. Online... 46 2. E-Mail... 46 3. Phone... 46 Contents English 39
Installation and Registration IMPORTANT: Do not connect the device to your PC before the software installation is completed. Use the following steps to install the POIbase Software on any PC running under Windows XP or Vista. Installation Guide Step 1: Insert the CD into the CD-/DVD-Drive. The installation wizard starts automatically. Should the wizard not pop up on its own, open My Computer, open the CD-/DVD-Drive and start the application setup.exe with a double click. Pic. 1: Start of installation Step 2: Follow the instructions of the installation wizard. The wizard will install the POIbase Software and all necessary drivers on your computer. You will have to click I accept the terms of the license agreement to begin the installation. Choose the target directory for the program. Click Next to continue. Click Install to begin the installation process. 40 English
Once the wizard has finished the installation of new drivers you will be asked to restart your computer. Do not do this. First, uncheck the restart my computer now option and click Finish. Pick Not now and finish the complete installation. IMPORTANT: Use the USB-Cable to Connect the POI PILOT 3000 GPS-Locator to your computer. Set the switch on the device to USB. When you connect the device to your computer for the first time Windows will automatically start the wizard to install new hardware. If you use Window Vista this process will be executed automatically. If you use Windows XP please follow the following guidelines. Pick the option Yes and click Next. Check the option Install Software automatically in the next window and click Next. Your computer starts the search for new drivers. This process can take a few minutes. Do not interrupt this process or shut down your computer before it is finished. Click Finish once the wizard reports success. Installation Guide Once the installation is finished the process will restart to install the second driver. Pick the option Yes and click Next. Check the option Install Software automatically in the next window and click Next. English 41
Your computer starts the search for new drivers. This process can take a few minutes. Do not interrupt this process or shut down your computer before it is finished. Click Finish once the wizard reports success. The driver installation for the POI PILOT 3000 GPS-Locator is complete. You can now start the POIbase software. Installation Guide Step 3: Should the POIbase software not start automatically after the installation is finished you can start it manually by clicking: Start Programs POIbase POI PILOT 3000 Start POI PILOT 3000 GPS-Locator. The POIbase Software will now show the login screen. Step 4: Click the button Register to register with POIcon for regular updates to your device. Fill out the registration. You have to enter a valid email address and the registration code. The registration code can be found on the CD itself. You only have to register once. Once the registration is finished you can login with your email address and password to start selecting POI-data. You can find more information on the use of the POIbase Software in the PDF-Manual of the program. 42 English
Tipps & Information LEDs on the decvice Left LED Green off Green on Orange blinks Orange on Right LED Red blinks Blue blinks Red/Blue blink Battery is fully charged Battery is being charged GPS-Receiver active GPS-Receiver searching for satellites These LEDs show different types of hazards and speed cameras. For more information on the LED functions read the PDF-Manual in the POIbase POI PILOT program group on your computer. Installation Guide English 43
In case you want to check the success of the program installation: Open your computers hardware manager. Windows XP: Start Control Panel System Hardware Hardware Manager Windows Vista: Control Panel Hardware Manager Installation Guide The hardware manager shows all devices connected to your computer. Once the POI PILOT 3000 GPS-Warner is connected to your computer it should be shown under Connections (COM und LPT). If the device is not connected to your computer this entry will not be shown. If you want to remove the POIbase Software from your computer use the following guidelines: Open the Control Panel and open the folder Software with a double click. You will now see a list of all programs installed on your computer. Look for the the entry POI PILOT 3000 GPS-Locator and click Remove. Once the wizard is done removing the program look for the entry Silicon Laboratories CP210x VCP Drivers for Windows 2000/XP/2003 Server/Vista and click Remove. Windows XP only: Look for the entry CP210x USB to UART Bridge and click Remove. 44 English
New installation without prior removal Please note: If you start the installation software, and there is an existing POIbase software installation on your computer, the installer program will ask if you want to reinstall the drivers or up date them. Clicking cancel will continue the installation without modifying the current drivers. Installation Guide English 45
Support 1. Online Our Online-Support center offers: Free Updates for many POICON-Products Help and support for your product Installation Guide www.poicon.com -> Service + Support 2. E-Mail We will be glad to answer any request for support or suggestion under support@poicon.com 3. Phone Orders: Orders, Suggestions and questions about further products +49 1805-764 266 Technical Support: Advice and tips concerning the installation and use of the program +49-900-1764266 Thank you for purchasing POIPiliot The POICON Team Hamburg 46 English