Überspannungsschutz. P: Enthalten

Transkript

1 SCHALTSCHRANKMONTAGE -Ausgang Relais Schaltschrankmontage Schaltschrankmontage Leiterplattenmontage DIN-Schienenmontage Einsteckmontage Baugruppen Zubehörteile HA/HD-Serie A Serie Steuerspannung A: 9 28 V D: 32 VDC AxxxxE: V Betriebs- Spannung 8: 8 53 V 6: 8 66 V Halbleiterrelais mit Nennleistung 12 bis 125 A bei 8 bis 66 V Gegengeschalteter SCR-Ausgang für erhöhte Zuverlässigkeit in gewerblichen und Schwerindustrieanwendungen Flexible Steuerspannung bis 32 VDC, 18 bis 36 V oder 9 bis 28 V Passive, extrem niedrige Eingangsstromaufnahme (2 bis ma DC typisch, Option mit Versionssuffix T ) R-C-Dämpferglied für zusätzliche dv/dt-dämpfung (nur Modelle HA8/HD8) Verfügbar mit Nullspannungsschalter (ohmsche Lasten) oder Momentanschalter (Phasensteuerung oder induktive Lasten) Passiver interner Überspannungsschutz (Versionssuffix P ), d. h. kein Bedarf an externer Schutzvorrichtung Auf Anfrage werkseitige Anbringung einer Wärmeleitfolie zur Vermeidung von Wärmeleitpaste (Verwendung des Versionssuffix H ) Überlastfestigkeit nach UL 58 und Kurzschlussfestigkeit (SCCR) bis 1 ka Hinweise: A B C D J K Nennlaststrom 12: 12 A (nur Versionssuffix 8) 25: 25 A 5: 5 A 75: 75 A (nur Versionssuffix 8) 9: 9 A 11: 11 A (nur Versionssuffix 8) 125: 125 A Überspannungsschutz Leer: Nicht enthalten P: Enthalten H A 8 25 E K P G Anschluss Leer: Schraubanschluss F: Schnellanschlussklemme (Einzelnes Polpaar [bis 25 A] Doppeltes Polpaar [5 A]) K: Mit Abstandshaltern für Installation auf PC-Hauptplatinen Eingangsstatus-LED Leer: Nicht enthalten G: Enthalten Dämpfungsglied Leer: Nicht enthalten S: Enthalten (Nur Hx8xx und Hx8xxT Nicht erforderlich mit Versionssuffix T, im Standardlieferumfang) S H T Wärmeleitfolie Leer: Nicht enthalten H: Enthalten,89 [22,6] Triggerschaltung Leer: Photo Triac T: Niederstrom-Phototransistor -1 1,75 [,5] Schaltmechanismus oder Schaltungsart Leer: Nullspannungseinschaltung -1: Unverzögertes Einschalten 2,25 [57,2],92 [23,3]

2 HA / HD8 Series Ratings from 12A to 8-53 V SCR output for heavy industrial loads Zero Voltage or instantaneous turn-on outputs UL/CSA/VDE Approved, CE Compliant to EN695-1 Improved SEMS screw and washer Redesigned housing with anti-rotation barriers or DC control Direct bond copper substrate EMC compliant to Level 3 Direct power lead frame Epoxy free design For Generation 3 datasheet click here PRODUCT SELECTION Control Voltage 12A 25A 5A 75A 9A 11A 125A -32 VDC HD812 HD825 HD85 HD875 HD89 HD811 HD Vrms HA812 HA825 HA85 HA875 HA89 HA811 HA Vrms HA812E HA825E HA85E HA875E HA89E HA811E HA8125E AVAILABLE OPTIONS Series Control Voltage A: 9-28 V D: -32 VDC AxxxxE: V Operating Voltage 8: 8-53 V Rated Load Current 12: 12 Amps 25: 25 Amps 5: 5 Amps 75: 75 Amps 9: 9 Amps 11: 11 Amps 125: 125 Amps Overvoltage Protection Blank: Not Included P: Included (3) H A 8 25 E K P G Termination Blank: Screw F: Quick Connect (1) (Up to 5 Amps models) K: Hex standoffs (2) Input Status LED Blank: Not Included G: Included Snubber Blank: Not Included S: Included S H -1 Thermal Pad Blank: Not Included H: Included Required for valid part number For options only and not required for valid part number * Not all part number combinations are available. Contact Crydom Technical Support for information on the availability of a specific part number. Switching Type Blank: Zero Voltage Turn-On -1: Instantaneous Turn-On () OUTPUT SPECIFICATIONS (5) Description 12A 25A 5A 75A 9A 11A 125A Operating Voltage (7-Hz) [Vrms] (6) Transient Overvoltage [Vpk] Maximum Off-State Leakage Rated Voltage [marms] (7) Minimum Off-State Maximum Rated Voltage [V/µsec] Maximum Load Current [Arms] (2)(8) Minimum Load Current [marms] Maximum 1 Cycle Surge Current (5/6Hz) [Apk] 13/1 239/25 597/625 95/1 115/12 132/15 167/175 Maximum On-State Voltage Rated Current [Vrms] Thermal Resistance Junction to Case (Rjc) [ C/W] Maximum 1/2 Cycle I² t for Fusing (5/6Hz) [A² sec] 66/6 285/ / /15 656/ / /1279 Minimum Power Factor (at Maximum Load) (3) Tel. +1 () Fax +1 ()

3 INPUT SPECIFICATIONS (5) Description HD8xx HA8xx HA8xxE Control Voltage Range -32 VDC (9) 9-28 Vrms Vrms Minimum Turn-On Voltage. VDC 9 Vrms 18 Vrms Must Turn-Off Voltage 1. VDC 1 Vrms. Vrms Maximum Reverse Voltage -32 VDC - - Minimum Input Current 7. ma 5 ma 16 ma Maximum Input Current 12 ma 1 ma 2 ma Nominal Input Impedance Current Regulated Maximum Turn-On Time [msec] 1/2 Cycle (1) 2 2 Maximum Turn-Off Time [msec] 1/2 Cycle 3 3 GENERAL SPECIFICATIONS (5) Description Parameters Dielectric Strength, Input/Output/Base (5/6Hz) Vrms Minimum Insulation Resistance (@ 5 VDC) 1 9 Ohm Maximum Capacitance, Input/Output 8 pf Ambient Operating Temperature Range - to 8 C Ambient Storage Temperature Range - to 125 C Weight (typical) 2.6 oz (7.9 g) Housing Material UL9 V- Baseplate Material Aluminum Input Terminal Screw Torque Range (in-lb/nm) / Load Terminal Screw Torque Range (in-lb/nm) 18-2 / SSR Mounting Screw Torque Range (in-lb/nm) 18-2 / Input/Load Terminal Screw Torque Range (in-lb/nm) (2) w/ K option 8-1 / Input/Output Terminal Screw Thread Size #6-32 UNC / #8-32 UNC Humidity per IEC % non-condensing LED Input Status indicatior w/ G option (green) MTBF (Mean Time Between Failures) at C ambient temperature (11) 11,61,553 hours (1,328 years) MTBF (Mean Time Between Failures) at 6 C ambient temperature (11) 7,21,376 hours (823 years) WIRING DIAGRAM V Load (12) 1 ( ) 2 ( ) 1 OUTPUT 2 Terminals Input Output Recommended Wire Sizes Wire Size (Solid / Stranded) 2 AWG (.2 mm 2 ) /.2 [minimum] 2 x 12 AWG (3.3 mm 2 ) / 3.3 [maximum] 2 AWG (.5 mm 2 ) /.518 [minimum] 2 x 1 AWG (5.3 mm 2 ) / 5.3 Wire Pull-Out Strength (lb)[n] 1 [.5] 9 [] 3 [133] 11 [9] Input Current (ma) Input Current vs Input Voltage INPUT 3 2 x 8 AWG (8. mm 2 ) / 8. [maximum] 9 [] DC Input Voltage ( / ) 3 (+ / ) EQUIVALENT CIRCUIT BLOCK DIAGRAMS Diagram: HAxxxx Diagram: HDxxxx /DC Converter Current Limiter (13) Trigger Circuit (1) (15) 1 -DC (13) Trigger Circuit (1) (15) DC 3 Current Limiter 2 Tel. +1 () Fax +1 ()

4 MECHANICAL SPECIFICATIONS () Tolerances: ±.2 in /.5 mm All dimensions are in: inches [millimeters] Screw Termination Hex Standoff Termination ( K Option) (2) 1.1 [27.9].9 [12.] Mounting Hole/Slot.19 [.9] DIA..89 [22.6] 1.1 [27.9].9 [12.] Mounting Hole/Slot.19 [.9] DIA. 1. [26.] 1.88 [7.6] 1 OUTPUT 2 INPUT [3.2] 2.25 [57.3] 1.88 [7.6] 1 OUTPUT 2 INPUT [3.2] 2.25 [57.3] 1. [25.] 1.75 [.5] 1. [25.] 1.75 [.5].93 [23.6] ( places) 1. [25.] Quick Connect Termination ( F Option) - Up to 25 Amp (1) Quick Connect Termination ( F Option) - Up to 5 Amp (1) Mounting Hole/Slot.19 [.9] DIA [.2].9 [12.] Faston Terminal(16).25 x [33.] Mounting Hole/Slot.19 [.9] DIA Faston Terminal(16) [.2].25 x ( places) [16.].5 [11.] 1.31 [33.] 1 OUTPUT 2 1 OUTPUT [7.6] INPUT [3.2] 2.25 [57.3] 1.88 [7.6] INPUT [3.2] 2.25 [57.3] 1. [35.6] 1.75 [.5] GENERAL NOTES Faston Terminal(16).187 x [31.8].9 [12.] 1. [35.6] 1.75 [.5] Faston Terminal(16).187 x.2 (1) Single pair (up to 25A) Double pair* (up to 5A). *Caution: User must connect both pairs. (2) Option K is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between.31 and.93 inches (.79 to 2.36 mm), and loads rated up to 5 Amps. For higher load currents, the K standoff temperature must not exceed 15 C. For additional application assistance please contact Crydom Technical Support. (3) Output will self trigger between 9-12Vpk, Min. power factor.7 or higher, not suituable for capacitive loads. () Instantaneous turn-on version is not recomended for capacitive loads. Use zero turn-on only. (5) All parameters at 25 C unless otherwise specified. (6) For S option, operating voltage frequency is 7-63Hz. (7) For parts with option S maximum leakage current is 1mA. (8) Heat sinking required, see derating curves. (9) Increase minimum voltage by 1V for operations from -2 to - C. (1) Turn-on time for instantaneous turn-on versions is.2 msec (DC Control Models) (11) All parameters at 5% power rating and 1% duty cycle (contact Crydom tech support for detailed report). (12) Load can be wired to either SSR output terminal 1 or 2. (13) Elective Input Status LED, G option (1) Elective Overvoltage Protection, P option. (15) Elective Internal Snubber, S option. (16) Mechanical dimensions vary from G3 models [31.8] For additional information or specific questions, contact Crydom Technical Support. Tel. +1 () Fax +1 ()

5 SURGE CURRENT INFORMATION 12 A A A A A A Non repetitive peak surge current at Tj initial ºC. 125 A Tel. +1 () Fax +1 ()

6 THERMAL DERATE INFORMATION 12 A 3ºC/W 5ºC/W No heatsink A 1.5ºC/W 2ºC/W 3ºC/W A.7ºC/W 1ºC/W 1.5ºC/W 2ºC/W A.5ºC/W.7ºC/W 1ºC/W 1.5ºC/W A.5ºC/W.7ºC/W 1ºC/W 1.5ºC/W A.5ºC/W.7ºC/W 1ºC/W 1.5ºC/W A.5ºC/W.7ºC/W 1ºC/W Tel. +1 () Fax +1 ()

7 AGENCY APPROVALS Designed in accordance with the requirements of IEC 6231 IEC : Electrostatic Discharge Level 3 IEC 61-- : Electrically Fast Transients Level 3 IEC : Electrical Surges Level 3 IEC : Vibration.33mm and.75mm Amplitude over 1-55 Hz IEC : Shock Resistance 15g/11ms E11699 E11695 (11 and 125A models) LR81689 (except 12, 11 and 125A models) 113 UG CESORIES New Accessories! Protective Cover & Hardware Kits Recommended Accessories Protective Cover Part number: KS11 Clear plastic cover compatible with all new S1 designs. Safety covers provide added protection from electric shock when installing or checking equipment. Cover KS11 Hardware Kit HK1 HK Heat Sink Part No. HS51DR HS31 / HS31DR HS251 Thermal Resistance [ºC/W] Lug Terminal TRM1 TRM6 Thermal Pad HSP-1 HSP-2 HS22 / HS22DR 2. Hardware Kit Part number: HK Bag with 2 square brass accessories and 2 screw 8-32 x 5/8 for output. Used to mount TMR1 lug terminals. HS21 / HS21DR HS172 HS151 / HS151DR HS122 / HS122DR HS13 / HS13DR HS11 1. HS73.7 HS72.7 HS53.5 HS33.36 HS23.25 Rev. 716 Tel. +1 () Fax +1 ()

8 DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. Disconnect all power before installing or working with this equipment. Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL ESPLOSIONE. Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura Verificare tutti i collegamenti e sostituire tutte le coperture prima dell accensione L'omissione di queste istruzioni provocherà la morte o lesioni serie 存在电击爆炸或电弧闪烁危险在操作此设备之前请先关闭电源若不遵守这些说明, 可能会导致严重的人身伤害甚至死亡 WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE The product's side panels may be hot, allow the product to cool before touching. Follow proper mounting instructions including torque values. Do not allow liquids or foreign objects to enter this product. Failure to follow these instructions can result in serious injury, or equipment damage. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. Respetar las instrucciones de montaje, y en particular los pares de apretado. No dejar que penetren líquidos o cuerpos extraños en el producto. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. Respecter les consignes de montage, et notamment les couples de serrage. Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, des lésions corporelles graves ou des dommages matériels. RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. Seguire le istruzioni di montaggio corrette. Non far entrare liquidi o oggetti estranei in questo apparecchio. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. Beachten Sie die Montageanweisungen, Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. 材料损坏和高温外壳的危险性产品的一侧面板可能很热, 在其冷却前请不要触碰遵照正确的安装说明, 包括扭矩值请勿让液体及其他异物进入本产品如不能正确执行这些操作说明, 极有可能造成严重人体伤害或者设备的损坏 Tel. +1 () Fax +1 ()

9 ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People s Republic of China Electronic Industry Standard SJ/T , Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium biphenyls diphenyl ethers (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T , 电子信息产品污染控制标识要求部件有毒有害物质或元素名称铅汞镉六价铬多溴联苯多溴二苯醚半导体芯片焊接点 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 5 Tel. +1 () Fax +1 ()