Drive and Motor Safety

Transkript

1 Drive and Motor Safety CMAFH Drive For Technology 2012 Drive and Motor Safety Gary Thrall Senior Product Support Engineer Bosch Rexroth Corporation Safety on Board Integrated, certified and consistent 1

2 Performance Level in total Performance Level of the combination of SRP/CS SRP/CS 1 PL 1 Cat 3 SRP/CS 2 PL 2 Cat 3 SRP/CS 3 PL 3 Cat 3 SRP/CS 4 SRP/CS PL 4 5 SRP/CS PL 5 6 SRP/CS PL 6 7 SRP/CS PL 7 8 SRP/CS PL 8 9 PL 9 PFH total = PFH Sensor + PFH IO + PFH SafetyPLC + n x PFH Drive Cat 3 PFH total = 2, , , x 4, PFH total = 5, < > PL d EN ISO :2006 Category 3 PL d 8

3 SafeMotion - More than just Switching Off! The evolution of safety technology Safety reaction Switching off Safety condition SafeMotion ; BRC/SPM; J. Ost 9

4 Conventional versus Integrated controller enable external monitoring unit (standstill, speed,...) E Drive M additional feedback G E E Drive Channel 1 Channel 2 two-channel switching-off M Conventional safety solution Drive-integrated safety technology ; BRC/SPM; J. Ost 10

5 Safety On Board with IndraDrive Note: - only Safe Torque Off in BASIC Encoders with only TTL interface or only serial interface are not allowed for integrated safety technology functions. 3 principles are realized to detect latent failures Dual channel data operation with diversity Cross data comparison of safety related functions Dynamization of static modes Due to this method one single failure may not deactivate the safety function --> Category 3 (recommended Safety level in most guidelines) A risk analysis by the machine builder and end user is required in accordance to Annex I of the European Community Directive for machines 98/37/EG All encoders with 1 Vpp signals (e. g. EnDat, HIPERFACE,...) and all resolvers supported by the encoder interface can be used for integrated safety technology. It is always the feedback at X4 connector that is evaluated. 11

6 Selection of safety functions SafeMotion Functional Safety in Automation Technology Control Communication Auto Set-up E Channel 1 M E Channel 2 Option S2 24V / 24V 12

7 Safety on Board - Functional Safety Safe Torque Off Safe Motion STO using 24V / 24V or 24V / 0V SLS using 24 V/ 24V X41 X41 channel 1 channel 2 power section X31/X32 X41 channel 1 channel 2 common parts transducer One L2 PFH value independent from control (opener / closer, opener / opener) SLS using SERCOS / 24V Safe Torque Off: PFH = 2 * /h SERCOS X41 channel 1 channel 2 common parts transducer Safe Motion: PFH drive and feedback = 5 * /h One S2 PFH value independent from the control and the safety technology feature. Separate PFH value for the feedback ; BRC/SPM; J. Ost 13

8 Functional Safety According to ISO Verification with SISTEMA Library for certified and standard components IEC IEC IEC IEC SRP/CS 1 SRP/CS 2 SRP/CS 3 SRP/CS SRP/CS 4 PL 1 PL 2 PL SRP/CS 5 3 SRP/CS PL PL 6 SRP/CS SRP/CS PL PL 6 9 PL PL safety switches safety I/O safety PLC safety drives Certified components ISO S input DP DP PPC SII IndraDrive S K1 safety switches I/O PLC Standard components Drive ISO ; BRC/SPM; J. Ost 14

9 SafeMotion Safe Torque Off (L2): EN ISO :2006 Category 3 PL = e IEC EN 62061:2005 EN :2007 SIL3 PFH d = 2 * /h MTTF d = 100 years (limitation by standard) Mission Time = 20 years The PFH values are based on a 100% duty cycle (24h/ 365 days) 15

10 SafeMotion Safe Motion (S2): EN ISO :2006 Category 3 PL = d IEC EN 62061:2005 EN :2007 SIL2 PFH d Drive = 3 * /h PFH d Feedback = 2 * /h (Stegmann/ Heidenhain motor feedback) MTTF d = 100 years (limitation by standard) Mission Time = 20 years To calculate the MTTF d value for a drive and feedback combination: Add the PFH values and convert then into a MTTF d value. Do not add the MTTF d values since they are limited to 100 years. The PFH values are based on a 100% duty cycle (24h/ 365 days) 16

11 SafeMotion Preliminary Data Safety Integrity Level SIL IEC Probability of dangerous failure per hour (1/h) PFH d Performance Level PL ISO IEC >= 10-5 to 10-4 a 1 >= 3 x 10-6 to 10-5 b 1 >= 10-6 to 3 x 10-6 c 2 >= 10-7 to 10-6 d 3 >= 10-8 to 10-7 e 4 < ISO Preliminary Data for IndraDrive, Safety on Board Safe Torque Off: PFH d = 2 * /h = 2 % of max. SIL3 value Safe Motion: PFH d Drive and feedback = 5 * /h = 5 % of max. SIL2 value 17

12 IEC New Terminology (not all available) EN : 2007 Functional safety for speed variable drives Safe Torque Off STO Safe Stop 1 SS1 Safe Stop 2 SS2 Safe Operating Stop SOS Safely-monitored Deceleration SMD 1) Safely-limited Acceleration SLA Safe Acceleration Range SAR Safely-limited Speed SLS Safe Speed Range SSR Safe Speed Monitor SSM ; BRC/SPM; J. Ost Safe Maximum Speed SMS 1) Safely-limited Increment Safe Direction Safely-limited Position SLI SDI SLP Safely-monitored Position SMP 1 ) Safe Brake Control SBC Safe Braking and Holding System SBS 1) Safely-limited Torque Safe Torque Range Safe Motor Temperature Safe Cam SLT STR SMT SCA 1) Not defined in IEC

13 Drive-Integrated Safety Features Safe Torque Off (STO) Safe Stop 1 (SS1) Safe Stop 1 - Emergency Stop (SS1-ES) Safe Stop 2 (SS2, SOS) Safely Monitored Deceleration (SMD) Safely Limited Speed (SLS) Safe Maximum Speed (SMS) Safely Limited Increment (SLI) Safe Direction (SDI) Safely Monitored Position (SMP) Safely Limited Position (SLP) Safe Door Locking (SDL) Safe I/O interface for Safety-PLC (SIO) new Safe Braking and Holding System (SBS) ; BRC/SPM; J. Ost 19

14 Drive Based Safety Functions Safe Torque Off (STO) v Safe Torque off (Stop Category 0*) t 0 t Drive is torque-less Power is cut safely (pulse inhibit) * according to EN

15 Drive Based Safety Functions Safe Stop 1 (SS1) / Safe Stop 2 (SS2) v Controlled Stopping according to stop category 1* (SS1) monitored stopping, control or drive controlled with safe deceleration t 0 t 1 t Torque-less standstill of the drives Power is cut safely (STO) Controlled Stopping according to stop category 2* (SS2) v, s t 0 t 1 t monitored stopping, control or drive controlled controlled standstill after stopping, no power off (SOS) * according to EN

16 Drive Based Safety Functions Safely Limited Speed (SLS) / Safely Limited Increment (SLI) v Within the Safe Mode a safely limited speed and / or a safely limited increment can be enabled (enabling device) t 0 t 1 t 30 v, s v, s t In case the speed/increment monitoring window will be triggered the drive will be safely stopped automatically in accordance with the stop category 1. 22

17 Drive Based Safety Functions Safe Direction (SDI) v In addition a safe direction (right, left) can be defined. 0 t In case the direction changes the drive will be safely stopped automatically in accordance with the stop category 1. 23

18 Drive Based Safety Functions Safe Maximum Speed (SMS 1 ) v Max The monitoring of a safely limited maximum speed is active always, regardless the operation mode of the drive (Automatic/Manual Mode) 120 t In case the parameterized maximum speed will be exceeded the drive will be safely stopped automatically in accordance with the stop category 1. 1) Not defined in IEC

19 Drive Based Safety Functions Safely Monitored Position (SMP 1 ) Working Area Position 1 Position 2 In the safe operation mode a working area (absolute position) can be defined In case the parameterized working area will be left, the drive will be safely stopped automatically in accordance with the stop category 1. 1) Not defined in IEC

20 Drive Based Safety Functions Safely Limited Position (SLP) active in normal and safe operation mode - The drive is not able to cross the limited switches - The drive is stopped automatically when the available deceleration torque would not be sufficient to stop the load before the parameterized position area will be left Offers cost saving by replacing hardware position limit switch v v max Max. Positive Limit Switch Max. deceleration deceleration s Negative Limit Switch 26

21 Drive Based Safety Functions Safely Monitored Deceleration safety in the stopping process NC-controlled stopping process with safely monitored deceleration (SMD) Braking of coupled drives: It may occur that individual axes must still accelerate, in order to stop the total movement n SMD Safe stop in a defined time due to predictive behavior of the drive The drive checks each cycle whether it is possible to stop within the time t 1. If this is not possible such as by wrong set point of the control, the drive takes over the braking. t 1 27

22 Safety on Board - Safe Braking and Holding System Safe braking and holding system a new milestone Safe Braking and Holding System (SBS) Fall protection for axes with gravity loads Operator protection in special operating mode World s only on board solution which complies with EN ISO , Cat. 3 PL d and EN SIL 2 Two independent brakes separately controlled and monitored by redundant, diverse channels in the drive Escalation strategy to protect the mechanical subsystems Active as well after energy cutting by emergency stop 28

23 Safety on Board - Safe Braking and Holding System During automatic operation the machines and equipment are running at full speed without operators During special operation mode persons may be present in the machine when following special safety precautions - Configuration - Measuring - Troubleshooting Vertical or inclined axes can even present a danger when they are switched off and inadvertently coming down 29

24 Safety on Board - Safe Braking and Holding System Fall protection of gravity-loaded axes Personal protection of operators during special operation mode Safe Braking and Holding system Effective even after energy cut-off through emergency stop 30

25 Safety on Board - Safe Braking and Holding System The safe braking and holding system is based on two independent brakes which are separately controlled and monitored by the redundant diversified channels in the drive. Safe energy cutting Universal integration of different brake types, e.g. two-channel selection of the safety feature e.g. safely-monitored deceleration two-channel control of the brakes IndraDrive HAT Safe feedback 31

26 SafeMotion functional safety in automation technology IndraDrive with safety functions a convincing technology Safety Technology made by the experts having more than 10 years field experience Scalable Safety Functions minimize the potential of tampering and therefore reduce the hazard for injury caused by passing the safety measures Increased productivity by reducing downtime Online Testing (Failure Detection) during runtime Cost savings by reduction of external components and wiring Minimal Movement in case of emergency by detecting failures within 2 ms High reliability due to an encapsulated, certified solution Stand-alone whether wired, or with or without a safety PLC 32

27 Coming Soon Safe Torque Off for IndraDrive Cs Safe Torque Off (L4): (A new type code to distinguish different features) IndraDrive Cs with L4 option is currently available for sale Certification by TÜV Rheinland is done L4 option will include STO (Safe Torque Off) and SBC (Safe Brake Control) SBC is 2-channel control of the standard holding brake so that if there is a short in either wire or a failure in one channel, the brake will still be applied. L4 STO circuit is completely redesigned from L1/L2 has safe mode within a test period. The test pulse is < 1ms. with on-line dynamization, no need for an acknowledgement contact to meet Cat. 4, PL e, SIL 3 -- the lifetime issue of the relay contact in the L1/L2 is gone. L4 connector for is no longer a D-sub 6-pin cage clamp connector with separate clamp for incoming and outgoing wire at each pin daisy-chain up to 25 axes. Just daisy chain 4 terminals with discrete wires from one drive to the next. This eliminates the cable management issues of the ribbon cable in previous design. Easier and less expensive. 33

28 Safe Torque Off for IndraDrive Cs SS1 functionality [single axis wired] with SS1-Funktion einer Achse in Verbindung mit einem Sicherheitsschaltgerät an external safety device: Reset + 24V 24 V Dynamisierte Ausgänge 24 V mit < 1 ms Testimpuls Single channel STO application over a single pole switch device Einkanalige STO-Anwahl über ein einpoliges Schaltgerät 24 V 24 V Dynamisierte Ausgänge mit < 1 ms Testimpuls Not Halt Externes Sicherheitsschaltgerät Kategorie 4, PL e, SIL 3 Z e i t v e r z ö g e r t IndraDrive Cs STO-Option Kategorie 4, PL e SIL3 Einpoliges Schaltgerät der Kategorie 3, PL d, SIL 2 mit Zwangsöffner gemäß EN IndraDrive Cs STO-Option Kategorie 4, PL e SIL3 Rückmeldung 24 V STO-Anwahl Ch1 24 V STO-Anwahl Ch2 E.Stopp 0 V Ground für Ch1 und Ch2 oder NC-Stopp Anwahl über 2 Öffnerkontakte SS1 function multiaxis with an external safety device and external wiring SS1-Funktion mehrerer Achsen mit Sicherheitsschaltgerät und externer Verdrahtung SBC-Funktion SBC Function 24 V STO-Anwahl Ch1 24 V STO-Anwahl Ch2 0 V Ground für Ch1 und Ch2 Anwahl über 1 Öffnerkontakt 24 V 24 V 24 V 24V 24 V 24 V 24 V SBC-Anwahl Ch 1 STO-Option STO-Option 1. Antrieb 2. Antrieb Nicht sichere Ansteuerung der Bremse aus der Standard-FW ODER Bremse 24 V Anwahl Ch1 Anwahl Ch1 SBC-Anwahl Ch 2 Bremse 0 V Anwahl Ch2 Anwahl Ch2 0 V 0 V 0 V 34

29 Safety on Board and Safe Motion - Additional Resources or just Google IFA SISTEMA for BGIA software to calculate PFHd and Performance Level to IEC for downloadable manuals including Safety on Board Application Manual 10 steps to performance level Handbook for the implementation of functional safety according to ISO Available in English next week. Bosch Rexroth Safety on Board hands-on workshop next scheduled for May 15 th and 16 th in Hoffman Estates (more to follow) 35

30 Functional Safety with Safety on Board Unexpected movements Risk for human and machine. Safety on Board Always on the safe side 36