6MS1600R17KE3-3WCH-C21MVTIOIN

Transkript

1 Key data 3x 975A rms at 789V rms, water cooled General information Stacks for various inverter application. Semiconductors, heat sinks, capacitors, drivers and sensors included. These are only technical data! Please read carefully the complete documentation and maintain the proper design environment! Especially note the EMC environment and the controller's functionality. Topology DC Link + B6I Application / Modulation Inverter / Sine Load type resistive, inductive Cooling water cooled Market wind Implemented sensors current, voltage, temperature Semicond. (Unit 1) none DC Link 10.5mF Semicond. (Unit 2) Driver signals IGBT IGBT 6x FF800R17KE3 Standards EN50178 optical HFBR-15X1 / HFBR-25X1 Sales - name 6MS16017E33W32779 Internal ID Mechanical drawing number 32779_MB Electrical drawing number Dimensions (width x depth x height) Weight 90 kg 1090 mm x 596 mm x 329 mm + DC Link Unit 2 ~ ~ ~ - Signal Conditioner & Monitor Driver 3 phases Electrical Interface Parallel Interface Optical Interface X2.. X5 1

2 Note Heat sink with copper cooling channel. Composites of fluid: Water and 52 vol. % Antifrogen N. Electrical data DC Link min typ max units Voltage V V Overvoltage shutdown within 150µs 1250 V Unit 2 AC min typ max units Voltage depending on controller V¼ÒÍÚè 789 V» Continuous current Continuous current overload cap. V¼ÒÍÚè = 789V», V = 1150V, TÍÒÐþÚ = 40 C, Tœ ù 125 C, f¼òíúè = 15Hz, fùþè = 1725Hz, cos(phi) = 1,00 I¼ÒÍÚè 975 A» TÍÒÐþÚ = 40 C, for overload capability 150% for 60s 666 A» Short time current TÍÒÐþÚ = 40 C, 10s, every 180s, initial load = 823A» I¼ÒÍÚè 1029 A» DC current no rotating field, TÍÒÐþÚ = 40 C I¼ÒÍÚè 488,0 AÈÝ Overcurrent shutdown within 15µs 1700 AÔþÈÏ Switching frequency fùþè 5000 Hz Power losses V¼ÒÍÚè = 789V, V = 1150V, TÍÒÐþÚ = 40 C, Tœ ù 125 C, f¼òíúè = 15Hz, fùþè = 1725Hz, cos(phi) = 1,00, I¼ÒÍÚè = 975A» PÐÓÙÙè W Power factor cos(phi)¼òíúè -1,00 1,00 General data min typ max units Power losses (PCB and capacitor) EMC test Insulation management is designed for according to IEC at named interfaces power control aux (24V) PÐÓÙÙ ÈÛà 400 W V ÛØÙÚ 2 kv V ÛØÙÚ 1 kv V»ÛØÃþ 1 kv V ÍÒþ 690 V» Insulation test voltage according to EN50178, f = 50Hz, t = 60s VÍÙÓÐ 2,5 kv» Important component data min typ max units DC Link capacitor C 10,50 mf type Foil Temperature range C Rated voltage per device Uç 1500 V Rated capacitance per device Cç 350 µf Capacitance tolerance per device Tol % Maximum ripple current per device, TÈÑÉ = 60 C IçÑÈà 60 A» wiring system series, parallel 1s, 30p Balance or discharge resistors per DC Link unit RÉ 6,0 kâ 2

3 Controller interface data min typ max units Auxiliary voltage VÈÛà VÈÝ Auxiliary power requirement VÈÛà = 24VÈÝ PÈÛà 40 W Driver and interface board see separate technical information TR110 / DR110 Driver core EiceDRIVER 2ED300C17-S Parallel interface board see separate technical information SAD101 Digital input level resistor to GND 1,8kÂ, capacitor to GND 4nF, high = on, min 15mA VÍÒ 0,0 15,0 V Digital output level open collector, low = ok, max 15mA VÓÛÚ 0,0 15,0 V Analog current outputs Unit 2 load max 1mA; at 975A VÈÒÈ ÓÛÚ 4,86 4,96 5,06 V Analog DC Link voltage output load max 1mA; at 1250V V ÓÛÚ 8,79 8,97 9,15 V Analog temperature output load max 1mA; at T Å = 57 C correspond to TÎ = 125 C VÅ ÓÛÚ 8,82 9,00 9,18 V Overtemperature shutdown at T Å = 60 C correspond to TÎ = 135 C VÅ ÓÛÚ Å 10 V Optical interface board see separate technical information OEA101 Optical input power 12 µw Optical output power 60 µw Heat sink water cooled / Thermal data min typ max units Water flow ÆV/Æt¾ÈÚþØ 16 dm³/min according cooling water specification from infineon Water pressure drop Æp¾ÈÚþØ 900 mbar Water pressure 8 bar Cooling water inlet temperature TÍÒÐþÚ C Water connection 3/4 in IGBT data unit 2 min typ max units Type assumed collector-emitter saturation voltage IÊ = 800A; VÃþ = 15V; TÝÎ = 125 C V Š ÙÈÚ 2,4 V parameter for linear model TÝÎ = 25 C VÊþæ 1,1 V parameter for linear model TÝÎ = 25 C rêþæ 1,125 mâ parameter for linear model TÝÎ = 125 C VÊþè 1 V parameter for linear model TÝÎ = 125 C rêþè 1,75 mâ turn-on / turn-off energy loss per pulse turn-on / turn-off energy loss per pulse thermal resistance, junction to case thermal resistance, case to heatsink TÝÎ = 25 C Eæ TÝÎ = 125 C Eè per IGBT RÚÌÎÊ 0,028 K/W per IGBT RÚÌÊÌ 0,017 K/W 165 / / 295 mj mj 3

4 Diode data unit 2 min typ max units Type assumed forward voltage IŒ = 800A; VÃþ = 0V; TÝÎ = 125 C VŒ 1,9 V parameter for linear model TÝÎ = 25 C VŒæ 1,15 V parameter for linear model TÝÎ = 25 C rœæ 0,813 mâ parameter for linear model TÝÎ = 125 C VŒè 1 V parameter for linear model TÝÎ = 125 C rœè 1,125 mâ reverse recovery energy TÝÎ = 25 C EØþÊæ 130 mj reverse recovery energy TÝÎ = 125 C EØþÊè 225 mj thermal resistance, junction to case thermal resistance, case to heatsink per Diode RÚÌÎÊ 0,064 K/W per Diode RÚÌÊÌ 0,039 K/W Environmental conditions min typ max units Storage temperature TÙÚÓØ C Ambient temperature minimum 0 C for optional optical interface TÈÑÉ C Operating temperature see chapter Heat sink water cooled / Thermal data Cooling air velocity (PCB and capacitor) VƒÍØ «2,0 m/s Air pressure standard atmosphere pƒíø hpa Humidity no condensation Rel. F 0 95 % Installation height m Vibration according to EN m/s² Continuous vibration according to EN m/s² Shock according to EN m/s² Protection degree IP00 Pollution degree 2 Dimensions width depth height mm Weight with heat sink approximation 90,0 kg 4

5 fo - derating curve IGBT (motor) cos(phi) = 1 TÊÓÓÐ ÑþÁÍÛÑ = 40 C fsw - derating curve IGBT (motor) cos(phi) = 1 TÊÓÓÐ ÑþÁÍÛÑ = 40 C I/IÒÓØÑ [%] I/IÒÓØÑ [%] få [Hz] fùþ [Hz] Transient thermal impedance per module TÊÓÓÐ ÑþÁÍÛÑ = 40 C 0,024 0,022 0,020 Zth heat sink to ambient [K/W] 0,018 0,016 0,014 0,012 0,010 0,008 0,006 0,004 0,002 i: rí[k/w]: τí[s]: 1 0, , ,0001 0, , ,56 4 0, ,73 0, time [s] 5

6 Mechanical drawing 6

7 Circuit diagram U in BOT U in TOP V in BOT V in TOP W in BOT W in TOP X2:19 X3:16 U error V error W error Temp. err Voltage err Sum. err X3:17 X2:10 X3:2,14 X4: 9 X2:8, 20 X4:13 X4:15 X4:14 X3:3,15 6 x HFBR 2521 ENABLE RESET 6 x HFBR 1521 Curr. error GND dig. GND dig GND dig P24-15V +15V 24V 15V/100mA Input Output In Out PTC Power supply Digital circuit Undervoltage Error messages Error messages V C E(sa t) / supply V C E(sa t) / supply V C E(sa t) / supply IGBT- DRIVER IGBT- DRIVER IGBT- DRIVER TOP BOT TOP BOT TOP BOT ϑ + U - + V - + W - X3:11 U current X3:12 V current X3:13 W current X3:10 Temperature X3:23 Voltage DC-Link X3:24 GND analog X3:25 GND analog OEA101 X5:1 + Output M an a Analog circuit TR101 / DR110 Overcurrent HB A Overcurrent HB B Overcurrent HB C Overcurrent HB D Overtemp. output stage Overtemp. PCB Overvoltage DC-Link High voltage area in grey Option V Voltage measurement safety separation between high voltage area X5:2 0V X5_Connector 3pole male low voltage area X5:3 True earth/shield female thread UNC4/40 X4_Connector 15pole male 1 1 front view front view female thread UNC4/40 female thread UNC4/40 X2_Connector 25pole male X3_Connector 25pole male For detailed technical information please refer the ModSTACK manual. ModSTACKB6_01_OEA101_Rev02 7

8 Nutzungsbedingungen Die in diesem Produktdatenblatt enthaltenen Daten sind ausschließlich für technisch geschultes Fachpersonal bestimmt. Die Beurteilung der Eignung dieses Produktes für Ihre Anwendung sowie die Beurteilung der Vollständigkeit der bereitgestellten Produktdaten für diese Anwendung obliegt Ihnen bzw. Ihren technischen Abteilungen. In diesem Produktdatenblatt werden diejenigen Merkmale beschrieben, für die wir eine liefervertragliche Gewährleistung übernehmen. Eine solche Gewährleistung richtet sich ausschließlich nach Maßgabe der im jeweiligen Liefervertrag enthaltenen Bestimmungen. Garantien jeglicher Art werden für das Produkt und dessen Eigenschaften keinesfalls übernommen. Sollten Sie von uns Produktinformationen benötigen, die über den Inhalt dieses Produktdatenblatts hinausgehen und insbesondere eine spezifische Verwendung und den Einsatz dieses Produktes betreffen, setzen Sie sich bitte mit dem für Sie zuständigen Vertriebsbüro in Verbindung (siehe Vertrieb&Kontakt). Für Interessenten halten wir Application Notes bereit. Aufgrund der technischen Anforderungen könnte unser Produkt gesundheitsgefährdende Substanzen enthalten. Bei Rückfragen zu den in diesem Produkt jeweils enthaltenen Substanzen setzen Sie sich bitte ebenfalls mit dem für Sie zuständigen Vertriebsbüro in Verbindung. Sollten Sie beabsichtigen, das Produkt in Anwendungen der Luftfahrt, in gesundheits- oder lebensgefährdenden oder lebenserhaltenden Anwendungsbereichen einzusetzen, bitten wir um Mitteilung. Wir weisen darauf hin, dass wir für diese Fälle - die gemeinsame Durchführung eines Risiko- und Qualitätsassessments; - den Abschluss von speziellen Qualitätssicherungsvereinbarungen; - die gemeinsame Einführung von Maßnahmen zu einer laufenden Produktbeobachtung dringend empfehlen und gegebenenfalls die Belieferung von der Umsetzung solcher Maßnahmen abhängig machen. Soweit erforderlich, bitten wir Sie, entsprechende Hinweise an Ihre Kunden zu geben. Inhaltliche Änderungen dieses Produktdatenblatts bleiben vorbehalten. Terms & Conditions of usage The data contained in this product data sheet is exclusively intended for technically trained staff. You and your technical departments will have to evaluate the suitability of the product for the intended application and the completeness of the product data with respect to such application. This product data sheet is describing the characteristics of this product for which a warranty is granted. Any such warranty is granted exclusively pursuant the terms and conditions of the supply agreement. There will be no guarantee of any kind for the product and its characteristics. Should you require product information in excess of the data given in this product data sheet or which concerns the specific application of our product, please contact the sales office, which is responsible for you (see sales&contact). For those that are specifically interested we may provide application notes. Due to technical requirements our product may contain dangerous substances. For information on the types in question please contact the sales office, which is responsible for you. Should you intend to use the Product in aviation applications, in health or live endangering or life support applications, please notify. Please note, that for any such applications we urgently recommend - to perform joint Risk and Quality Assessments; - the conclusion of Quality Agreements; - to establish joint measures of an ongoing product survey, and that we may make delivery depended on the realization of any such measures. If and to the extent necessary, please forward equivalent notices to your customers. Changes of this product data sheet are reserved. 8

9 Sicherheitshinweise Bevor Sie mit der Installation und dem Betrieb der Baugruppe beginnen, lesen Sie bitte sorgfältig alle Sicherheitshinweise, Warnungen und beachten Sie die angebrachten Warnschilder. Vergewissern Sie sich, dass alle Warnschilder in leserlichem Zustand verbleiben und fehlende oder beschädigte Schilder ersetzt werden. Safety Instructions Prior to installation and operation, all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and that missing or damaged signs are replaced. To installation and operation, all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and that missing or damaged signs are replaced. 9