Operating Instructions Busch-Dimmer. Universal relay insert 6404 U Rev

Transkript

1 Pos : 2 / #N eus truktur #/Online-Dokumentation (+KN X)/Titelbl ätter/di mmer/titelbl att - @ 1 === Ende der Liste für T extmar ke Cover === Rev Busch-Dimmer Universal relay insert 6404 U

2 Pos : 4 / #N eus truktur #/Online-Dokumentation (+KN X)/Inhalts verz eic hnis (--> Für alle D okumente <--)/Inhalts verz @ 1 === Ende der Liste für T extmar ke TOC === Busch-Dimmer 1 Safety Intended use Environment Operation Technical data Setup and function Features of function and equipment Possible combinations Installation and electrical connection Requirements for the electrician Mounting Electrical connection

3 Pos : 7 / #N eus truktur #/Online-Dokumentation (+KN X)/Sicherheits hinweis e und Hi nweis e (--> F ür all e D okumente <--)/Warnhinweis e/sicherheit @ 1 Pos : 11 / #Neustr uktur#/online-dokumentation (+KNX)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise - U mwelt/hi nweis - U mwelt - Hinweis @ 1 Pos : 13 / #Neustr uktur#/online-dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Busch-Dimmer Safety Pos : 6 / #N eus truktur #/Online-Dokumentation (+KN X)/Ü bersc hriften (--> Für alle Dokumente <--)/1. Ebene/S Safety Warning Electric voltage! Risk of death and fire due to electrical voltage of 230 V. Work on the 230V supply system may only be performed by authorised electricians! Disconnect the mains power supply prior to installation and/or disassembly! Pos : 8 / #N eus truktur #/Online-Dokumentation (+KN X)/Ü bersc hriften (--> Für alle Dokumente <--)/1. Ebene/A - F/Bes timmungsgemäß er Gebrauc Intended use Pos : 9 / #N eus truktur #/Online-Dokumentation (+KNX)/Bestimmungsgemäßer Gebrauch (--> Für alle Dokumente <--)/Bus ch-di mmer /Besti mmungsgemäß er Gebr @ 1 The device is to be used exclusively with the components that are supplied and licensed as described in chapter "Setup and function". Pos : 10 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/1. Ebene/U - Z/U Environment Consider the protection of the environment! Used electric and electronic devices must not be disposed of with domestic waste. The device contains valuable raw materials which can be recycled. Therefore, dispose of the device at the appropriate collecting depot. Pos : 12 / #Neustr uktur#/online-dokumentation (+KNX)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise - U mwelt/hi nweis - U mwelt - Entsorgung @ 1 All packaging materials and devices bear the markings and test seals for proper disposal. Always dispose of the packaging material and electric devices and their components via the authorized collecting depots and disposal companies. The products meet the legal requirements, in particular the laws governing electronic and electrical devices and the REACH ordinance. (EU Directive 2002/96/EC WEEE and 2002/95/EC RoHS) (EU REACH ordinance and law for the implementation of the ordinance (EC) No.1907/2006)

4 Pos : 16 / #Neustr uktur#/online-dokumentation (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Busch-Dimmer Operation Pos : 14 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/1. Ebene/A - F /Bedi Operation Pos : 15 / #Neustr uktur#/online-dokumentati on (+KN X)/Bedi enung/di mmer/bedi enung - @ 1 The universal relay insert makes control possible in the two operating modes "Switch" and "Timer". The connected loads can be controlled directly with control element " ". See the respective operating instructions. Fig. 1: Insert with selector potentiometer Operating mode Switch Set the selector potentiometer (Fig. 1 (1) on 0/I. Pressing the top half of the rocker switch switches the light on. Pressing the bottom half of the rocker switch switches the light off. Operating mode Timer The switch-off delay can be set in five steps between 30 and 300 seconds, see table. Set the selector potentiometer (Fig. 1 (1)) to the desired value. Pressing the top half of the rocker switch switches the light on. The light will switch off automatically after the time set on the potentiometer. A manual switch-off is not possible. If the button is pressed once more during this time, the switch-off time will be restarted. Potentiometer setting Switch-off time 0/I No timer-controlled switch-off seconds 30 seconds 60 seconds 120 seconds 180 seconds 300 seconds Control via extension unit button Alternatively, control is also possible via an extension push-button, which switches the light on and off

5 Pos : 18 / #Neustr uktur#/online-dokumentation (+KNX)/Technische Daten/Dimmer/Technische Daten - @ 1 Pos : 19 / #Neustr uktur#/online-dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Busch-Dimmer Technical data Pos : 17 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/1. Ebene/S - T/Technische Technical data General Mains voltage 230 V AC ± 10%, 50 Hz Nominal power 2300 W/VA Maximum cable length of push-button 100 m Inputs 1 Polling voltage 230 V AC, sensing pulse, L-wire Outputs 1 normally open contact, potential-bound Nominal current 10 AX Power consumption < 1 W Ambient temperature range C Protection type IP

6 Pos : 22 / #Neustr uktur#/online-dokumentation (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Leerzeile Abstand @ 1 Pos : 24 / #Neustr uktur#/online-dokumentati on (+KN X)/Aufbau und Funktion/Dimmer/Funktionen - @ 1 Pos : 26 / #Neustr uktur#/online-dokumentati on (+KN X)/Kombi nations möglichkeiten/di mmer/kombinati ons möglichkeiten - @ 1 Pos : 27 / #Neustr uktur#/online-dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Busch-Dimmer Setup and function Pos : 20 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/1. Ebene/A - F/Aufbau und Setup and function Pos : 21 / #Neustr uktur#/online-dokumentati on (+KN X)/Lastarten/Lastarten Gl üh Halo NV-Hal o mit konv-trafo+elekt-trafo @ 1 The device is intended for the activation of the following types of loads: 230 V incandescent lamps 230 V halogen lamps Low-voltage halogen lamps with conventional transformers Low-voltage halogen lamps with electronic transformers Fluorescent lamps Pos : 23 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/2. Ebene/A - F/Funktions- und Aus stattungs mer kmal Features of function and equipment With operating mode switch (selector potentiometer) for operating modes "Switch" and "Timer". Switch-off delay adjustable in five steps between 30 and 300 seconds. Operation also possible via conventional push-buttons (2020 US, 2021/6 UK). Fixing via keyholes or enclosed spring claws Pos : 25 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/2. Ebene/G - L/Kombinati ons Possible combinations 6404 U X

7 Pos : 29 / #Neustr uktur#/online-dokumentation (+KNX)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sic herheit - Ni eders pannungs- und 230 @ 1 Pos : 31 / #Neustr uktur#/online-dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch @ 1 Busch-Dimmer Installation and electrical connection Pos : 28 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/1. Ebene/M - O/M ontage und el ektrisc her Anschl Installation and electrical connection Warning Electric voltage! Risk of death due to electrical voltage of 230 V during short-circuit in the low-voltage line. Low-voltage and 230 V lines must not be installed together in a flush-mounted socket! Pos : 30 / #Neustr uktur#/online-dokumentation (+KNX)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sic herheit - F ac hkenntniss Requirements for the electrician Warning Electric voltage! Install the device only if you have the necessary electrical engineering knowledge and experience. Incorrect installation endangers your life and that of the user of the electrical system. Incorrect installation can cause serious damage to property, e.g. due to fire. The minimum necessary expert knowledge and requirements for the installation are as follows: Apply the "five safety rules" (DIN VDE 0105, EN 50110): 1. Disconnect from power; 2. Secure against being re-connected; 3. Ensure there is no voltage; 4. Connect to earth and short-circuit; 5. Cover or barricade adjacent live parts. Use suitable personal protective clothing. Use only suitable tools and measuring devices. Check the supply network type (TN system, IT system, TT system) to secure the following power supply conditions (classic connection to ground, protective earthing, necessary additional measures, etc.)

8 Pos : 33 / #Neustr uktur#/online-dokumentation (+KNX)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sic herheit @ 1 Pos : 36 / #Neustr uktur#/online-dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/ Seitenumbruch 1 Busch-Dimmer Installation and electrical connection Pos : 32 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/2. Ebene/M - O/M Mounting Warning Electric voltage! Risk of death and fire due to electrical voltage of 230 V. Work on the 230V supply system may only be performed by authorised electricians! Disconnect the mains power supply prior to installation and/or disassembly! Pos : 34 / #Neustr uktur#/online-dokumentati on (+KN X)/Montage/alle Geräte/M ontage - UP-Dos en - DIN oder geeignetes Aufputzgehaeuse - Ohne Doc vari abl @ 1 The flush-mounted insert must only be installed in flush-mounted wall boxes according to DIN , Part 1, or suitable surface-mounted housings. Pos : 35 / #Neustr uktur#/online-dokumentati on (+KN X)/Montage/Di mmer/montage - @ 1 Spring claw attachment 1. Push the insert into the box so that the spring claws are guided into the groove on both sides. Fig. 2: Spring claw attachment Releasing the spring claws The insert can be pulled out of the box once the spring claws have been released. 1. Push a screwdriver through the hole in the mounting plate. 2. Loosen the spring claws from the box by moving the screwdriver (1). 3. Press the spring claws in the box toward the rear (2). Fig. 3:Releasing the spring claws

9 Pos : 38 / #Neustr uktur#/online-dokumentati on (+KN X)/Ansc hlus s/di mmer/ansc hluss - @ 1 === Ende der Liste für T extmar ke Content === Busch-Dimmer Installation and electrical connection Pos : 37 / #Neustr uktur#/online-dokumentati on (+KN X)/Übersc hriften (--> Für all e D okumente <--)/2. Ebene/A - F /El ektrisc her Ansc Electrical connection Fig. 4: 6404 U with extension unit push-button (e.g. 2020/4 US, 2021/6 U)

10 === Ende der Liste für T extmar ke Bac kc over === Busch-Dimmer Pos : 40 / #Neustr uktur#/online-dokumentati on (+KN X)/Rüc ksei ten (--> Für alle Dokumente <--)Rüc ks eite - Busc h-j aeg er - Allgemein ( @ 1 A member of the ABB Group Busch-Jaeger Elektro GmbH PO box Lüdenscheid Freisenbergstraße Lüdenscheid Germany Notice We reserve the right to at all times make technical changes as well as changes to the contents of this document without prior notice. The detailed specifications agreed to at the time of ordering apply to all orders. ABB accepts no responsibility for possible errors or incompleteness in this document Rev info.bje@de.abb.com Central sales service: Phone: +49 (0) Fax: +49 (0) We reserve all rights to this document and the topics and illustrations contained therein. The document and its contents, or extracts thereof, must not be reproduced, transmitted or reused by third parties without prior written consent by ABB. Copyright 2012 Busch-Jaeger Elektro GmbH All rights reserved