Digitales Eingangsmodul BMT-DI 9. Beschreibung Das Modul mit digitalen Eingängen ist für dezentrale Schaltaufgaben entwickelt worden. Es ist geeignet zur Erfassung von potentialfreien Schalterzuständen, z. B. elektrische Endlagenschalter an Lüftungsklappen oder Hilfskontakte bei Leistungsschützen. Je nachdem wie der Jumper J eingestellt ist, können die Eingänge als Kontakt- und Spannungseingänge (A, VAC/DC, Jumper J - A) oder mit einer Ansteuerung nach (A, Jumper J - A) betrieben werden. Von einem BACnet- Client können die Eingänge über Standard-Objekte abgefragt werden. Die Adressierung des Moduls und die Einstellung der Baudrate erfolgt über die beiden Adressschalter (x / x) auf der Frontseite. Es können die Adressen bis F9 sowie die Baudraten 96 Bd, 9 Bd, Bd, 576 Bd, 76 Bd und 5 Bd eingestellt werden. 9999-. Wichtige Hinweise Konformitätserklärung Das Gerät wurde nach den geltenden Normen geprüft. Die Konformität wurde nachgewiesen. Die Konformitätserklärung ist beim Hersteller BT NETCOM GmbH abrufbar. Hinweise zur Gerätebeschreibung Die Beschreibung enthält Hinweise zum Einsatz und zur Montage des Geräts. Sollten Fragen auftreten, die nicht mit Hilfe dieser Anleitung geklärt werden können, sind weitere Informationen beim Lieferanten oder Hersteller einzuholen. Die angegebenen Vorschriften/ichtlinien zur Installation und Montage gelten für die Bundes republik Deutschland. Beim Einsatz des Geräts im Ausland sind die nationalen Vorschriften in Eigenverantwortung des Anlagenbauers oder des Betreibers einzuhalten. Sicherheitshinweise Für die Montage und den Einsatz des Geräts sind die jeweils gültigen Arbeitsschutz-, Unfall verhütungs- und VDE-Vorschriften einzuhalten. Facharbeiter oder Installateure werden darauf hingewiesen, dass sie sich vor der Installation oder Wartung der Geräte vorschriftsmäßig entladen müssen. Montage- und Installationsarbeiten an den Geräten dürfen grundsätzlich nur durch qualifiziertes Fachpersonal durchgeführt werden, siehe Abschnitt qualifiziertes Fachpersonal. Jede Person, die das Gerät einsetzt, muss die Beschreibungen dieser Anleitung gelesen und verstanden haben. Warnung vor gefährlicher elektrischer Spannung Gefahr bedeutet, dass bei Nicht beachtung Lebensgefahr besteht, schwere Körper verletzungen oder erhebliche Sach schäden auftreten können. Qualifiziertes Fachpersonal Qualifiziertes Fachpersonal im Sinne dieser Anleitung sind Personen, die mit den beschriebenen Geräten vertraut sind und über eine ihrer Tätigkeit entsprechenden Qualifikation verfügen. Hierzu gehören zum Beispiel: Berechtigung zum Anschluss des Geräts gemäß den VDE- Bestimmungen und den örtlichen EVU-Vorschriften sowie Berechtigung zum Ein-, Aus- und Freischalten des Geräts unter Berück sichtigung der innerbetrieblichen Vorschriften; Kenntnis der Unfallverhütungsvorschriften; Kenntnisse über den Einsatz und Gebrauch des Geräts innerhalb des Anlagensystems usw.. Technische Daten BACnet-Schnittstelle Protokoll Übertragungsrate 96... 5 Bd (Werkseinstellung 96 Bd) Verkabelung S5 Zweidrahtbus mit Potentialausgleich in Bus-/Linientopologie Versorgung Betriebsspannungsbereich... V AC/DC (SELV) Stromaufnahme 5 ma (AC) / 75 ma (DC) Einschaltdauer relativ % Eingangsseite Eingangsspannung V DC High-Signalerkennnung >7 V AC/DC Gehäuse Abmessungen BxHxT 5 x 7 x 65 mm Gewicht g Einbaulage beliebig Montage Tragschiene TH5 nach IEC 675 Anreihbar ohne Abstand Nach dem Anreihen von 5 Modulen oder einer maximalen Stromaufnahme von A (AC oder DC) pro Anschluss am Netzgerät muss mit der Ver sorgungs spannung neu extern angefahren werden. Material Gehäuse Polyamid 6.6 V Klemmen Polyamid 6.6 V Blende Polycarbonat Schutzart (IEC 659) Gehäuse IP Klemmen IP Anschlussklemmen Versorgung und Bus -polige Anschlussklemme max.,5 mm² eindrähtig max., mm² feinstdrähtig Aderndurchmesser, mm bis max., mm (Anschlussklemme und Brückenstecker als Zubehör in der Verpackung) Geräteanschluss Ausgänge max. mm² eindrähtig max.,5 mm² feinstdrähtig Aderndurchmesser, mm bis max.,7 mm Schutzbeschaltung Verpolschutz der Betriebsspannung Verpolschutz von Speisung und Bus Temperaturbereich Betrieb -5 C... +55 C Lagerung - C... +7 C Anzeige Betrieb und Bustätigkeit grüne LED Fehlermeldung rote LED Zustand der Eingänge gelbe LEDs. Prinzipbild A/ A / BUS BUS 5. Anschlussbild C V C 5 6 7 9 on S-5 ISC - CPU 9 C A V AC/DC A A A BUS BUS 5 J C METZ CONNECT Im Tal 776 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5- Vertrieb durch IA CONNECT GmbH und BT NETCOM GmbH Montageanleitung siehe www.metz-connect.com
6. Montage Anlage spannungsfrei schalten Gerät auf Tragschiene (TH5 nach IEC 675, Einbau in Elektroverteiler / Schalttafel) setzen Installation Die Elektroinstallation und der Geräteanschluss dürfen nur durch qualifiziertes Fachpersonal unter Beachtung der VDE- Bestimmungen und örtlicher Vorschriften vorgenommen werden.. Anschlussklemme für Busanschluss einstecken. 7. Netzwerkadresse und Bitrate einstellen Schalter zur Konfiguration Hexadezimalschalter x, x definieren die Netzwerkadresse ( - F9; z.b. F9h = 5x6+9 = 9d) und die Baudrate (FA - FF) Schalter x auf E drehen ( Gerät ist als Slave konfiguriert) Schalter x auf F drehen, um die Baudrate einzustellen Schalter x auf F drehen und Sekunde warten Die rote und grüne LED blinken, wenn die Baudrate im EEPOM gespeichert wurde Schalter x drehen um die Netzwerkadresse einzustellen Schalter x drehen um die Netzwerkadresse einzustellen. Anschlussbeispiele Anschlussbeispiele + A ( V AC /DC) A () 9 C Anschlussbeispiel A ( V AC /DC) A () 9 C Adressschalter x F F F F F F Adressschalter x A B C D E F X X X X Kabel für Busanschluss anschließen Bitrate (Bit/s) 96 9 576 76 5 Werkseinstellung: 96 Bit/s EO 9 5 BMT-DI EO 9 5 BMT-DI 5 mm 5 C 5 C eihenmontage 5 6 Das Modul ist ohne Abstand anreihbar. Bei eihenmontage Brückenstecker aufstecken, er verbindet Bus und Versorgungsspannung bei nebeneinander montierten Modulen. Nach dem Anreihen von 5 Modulen oder einer maximalen Stromaufnahme von A (AC oder DC) pro Anschluss am Netzgerät muss mit der Ver sorgungs spannung neu extern angefahren werden. 9. Beschreibung der Software Device Object Object_Identifier device, default instance: + Network-Address W-E Object_Name max. 5 Bytes, default BMT-DI_ + Network-Address (Hexadecimal) W-E Object_Type DEVICE () System_Status OPEATIONAL () Vendor_Name BT Netcom GmbH Vendor_Identifier Model_Name BMT-DI Firmware_evision. Application_Software_Version. Protocol_Version Protocol_evision Protocol_Services_Supported readproperty, writeproperty, device-communication-control, reinitialize-device, unconfirmed-cov-event-notification, who-has, who-is Protocol_Object_Types_Supported DEVICE, BINAY_INPUT, GOUP Object_List [] device, binary-input, group... Max_APDU_Length_Accepted 6 Segmentation_Supported NO_SEGMENTATION () APDU_Timeout Number_Of_APDU_etries Device_Address_Binding - Database_evision Description BMT_DI Max_Master 7 W-E Max_Info_Frames W-E METZ CONNECT Im Tal 776 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5- Vertrieb durch IA CONNECT GmbH und BT NETCOM GmbH Montageanleitung siehe www.metz-connect.com
Binary Input Objects... Object_Identifier binary-input, instance Object_Name Input Input Object_Type BINAY_INPUT () Present_Value INACTIVE () / ACTIVE () W Status_Flags IN_ALAM: FAULT: OVEIDDEN: OUT_OF_SEVICE: / Event_State NOMAL () Out_Of_Service FALSE () / TUE () W Polarity NOMAL () / EVESE () W-E Inactive_Text Off Active_Text On Notification_Class Unsubscribed UnconfirmedCOVNotification : no COV notification, : local broadcast, : global broadcast W-E Function Table for Binary Input Out_Of_Service Polarity Binary Input Present_Value OUT_OF_SEVICE Group Object... Object_Identifier group, instance Object_Name Group Group Object_Type GOUP () Present_Value Present_Value of Binary Inputs, see next Table List_Of_Group_Members see next Table Group Members of Groups Binary Input 5 6 7 9 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 5 x x x x x 6 x x x x x 7 x x x x x x x 9 x x x x x x x x x x: Present_Value is writeable and not affected by inputs METZ CONNECT Im Tal 776 Blumberg Deutschland Tel. +9 77 5- Fax +9 77 5- Vertrieb durch IA CONNECT GmbH und BT NETCOM GmbH Montageanleitung siehe www.metz-connect.com
Digital Input Module BMT-DI 9. Description The module with digital inputs is designed for local switching operations. It is suitable to record potential-free switching states as for example electrical limit switches of ventilation valves or auxiliary contacts of power contactors. The inputs can be operated as contact and voltage inputs (A, VAC/DC, jumper J - A) or with actuation to (A, jumper J - A), depending on the setting of the jumper J. The inputs can be scanned by standard objects via a BACnet-Client. Addressing of the module and baud rate setting are done with the two address switches (x / x) on the front. Possible settings are addresses to F9 and baud rates 96 Bd, 9 Bd, Bd, 576 Bd, 76 Bd and 5 Bd. 9999-. Declaration of Conformity The device was tested according to the applicable standards. Conformity was proofed. The declaration of conformity is available at the manufacturer BT NETCOM GmbH. Notes egarding Device Description These instructions include indications for use and mounting of the device. In case of questions that cannot be answered with these instructions please consult supplier or manufacturer. The indicated installation directions or rules are applicable to the Federal epublic of Germany. If the device is used in other countries it applies to the equipment installer or the user to meet the national directions. Safety Instructions Keep the applicable directions for industrial safety and prevention of accidents as well as the VDE rules. Technicians and/or installers are informed that they have to electrically discharge themselves as prescribed before installation or maintenance of the devices. Only qualified personnel shall do mounting and installation work with the devices, see section qualified personnel. The information of these instructions have to be read and understood by every person using this device. Symbols Warning of dangerous electrical voltage Danger means that non-observance may cause risk of life, grievous bodily harm or heavy material damage. Qualified Personnel Qualified personnel in the sense of these instructions are persons who are well versed in the use and installation of such devices and whose professional qualification meets the requirements of their work. This includes for example: Qualification to connect the device according to the VDE specifications and the local regulations and a qualification to put this device into operation, to power it down or to activate it by respecting the internal directions. Knowledge of safety rules. Knowledge about application and use of the device within the equipment system etc.. Technical Data BACnet Interface Protocoll Transmission rate 96... 5 Bd (factory setting 96 Bd) Cabling S5 two wire bus with voltage equalizing cable in bus / line topology Supply Operating voltage range... V AC/DC (SELV) Current consumption 5 ma (AC) / 75 ma (DC) elative duty cycle % Input Input voltage V DC High-signal recognition >7 V AC/DC Housing Dimensions WxHxD. x. x.6 in. (5 x 7 x 65 mm) Weight g Mounting position any Mounting standard rail TH5 per IEC 675 Mounting in series the maximum quantity of modules without space connected in line is limited to 5 or to a maximum power consumption of Amps (AC or DC) per connection to the power supply. For any similar block of additional modules a separate connection to the power supply is mandatory. Material Housing Polyamide 6.6 V Terminal blocks Polyamide 6.6 V Cover plate Polycarbonate Type of protection (IEC 659) Housing IP Terminal blocks IP Terminal blocks Supply and bus pole terminal block max. AWG 6 (,5 mm²) solid wire max. AWG (, mm²) stranded wire Wire diameter min.. mm up to max.. mm (terminal block and jumper plug are included to each packing unit) Module connection Input/Output max. AWG (. mm²) solid wire max. AWG (.5 mm²) stranded wire Wire diameter min.. mm up to max.7 mm Protective circuitry polarity reversal protection of operating voltage polarity reversal protection of supply and bus Temperature range Operation -5 C... +55 C Storage - C... +7 C Display Operating / bus activity green LED Error indication red LED Status of the inputs yellow LED. Wiring Diagram A/ A / BUS BUS 5. Connection Diagram C V C 5 6 7 9 on S-5 ISC - CPU 9 C A V AC/DC A A A BUS BUS 5 J C METZ CONNECT Im Tal 776 Blumberg Germany Phone +9 77 5- Fax +9 77 5- Distributed by IA CONNECT GmbH and BT NETCOM GmbH Mounting instruction see www.metz-connect.com
6. Mounting Power down the equipment Mount the module on standard rail (TH5 per IEC 675 in junction boxes and/or on distribution panels). Installation Electric installation and device termination shall be done by qualified persons only, by respecting all applicable specifications and regulations. Plug in the terminal block for bus connection 7. Network adress and Bit rate setting Configuration Switches Hexadecimal Switches x, x define the Network-Address ( - F9; e.g. F9h = 5x6+9 = 9d) and Baudrate (FA FF). Turn Switch x to E (Device is temporaryly configured as Slave) Turn Switch x to A F to select Baudrate Turn Switch x to F, wait Second ed and green LEDs are blinking when Baudrate ist stored in EEPOM Turn Switch x to select Network-Address Turn Switch x to select Network-Address. Connection examples Connection examples + A ( V AC /DC) A () 9 C Connection example A ( V AC /DC) A () 9 C Adress switch x F F F F F F Adress switch x A B C D E F Bitrate (Bit/s) 96 9 576 76 5 X X X X Connect the cable for bus supply Factory setting: 96 Bit/s EO 9 5 EO 9 5 5 mm BMT-DI BMT-DI 5 C 5 C Mounting in series 5 6 The module can be aligned without interspace. Use the jumper plug to connect bus and supply voltage when the modules are mounted in series. The maximum quantity of modules connected in line is limited to 5 or to a maximum power consumption of Amps (AC or DC) per connection to the power supply. For any similar block of additional modules a separate connection to the power supply is mandatory. 9. Software Description Device Object Object_Identifier device, default instance: + Network-Address W-E Object_Name max. 5 Bytes, default BMT-DI_ + Network-Address (Hexadecimal) W-E Object_Type DEVICE () System_Status OPEATIONAL () Vendor_Name BT Netcom GmbH Vendor_Identifier Model_Name BMT-DI Firmware_evision. Application_Software_Version. Protocol_Version Protocol_evision Protocol_Services_Supported readproperty, writeproperty, device-communication-control, reinitialize-device, unconfirmed-cov-event-notification, who-has, who-is Protocol_Object_Types_Supported DEVICE, BINAY_INPUT, GOUP Object_List [] device, binary-input, group... Max_APDU_Length_Accepted 6 Segmentation_Supported NO_SEGMENTATION () APDU_Timeout Number_Of_APDU_etries Device_Address_Binding - Database_evision Description BMT_DI Max_Master 7 W-E Max_Info_Frames W-E METZ CONNECT Im Tal 776 Blumberg Germany Phone +9 77 5- Fax +9 77 5- Distributed by IA CONNECT GmbH and BT NETCOM GmbH Mounting instruction see www.metz-connect.com
Binary Input Objects... Object_Identifier binary-input, instance Object_Name Input Input Object_Type BINAY_INPUT () Present_Value INACTIVE () / ACTIVE () W Status_Flags IN_ALAM: FAULT: OVEIDDEN: OUT_OF_SEVICE: / Event_State NOMAL () Out_Of_Service FALSE () / TUE () W Polarity NOMAL () / EVESE () W-E Inactive_Text Off Active_Text On Notification_Class Unsubscribed UnconfirmedCOVNotification : no COV notification, : local broadcast, : global broadcast W-E Function Table for Binary Input Out_Of_Service Polarity Binary Input Present_Value OUT_OF_SEVICE Group Object... Object_Identifier group, instance Object_Name Group Group Object_Type GOUP () Present_Value Present_Value of Binary Inputs, see next Table List_Of_Group_Members see next Table Group Members of Groups Binary Input 5 6 7 9 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 5 x x x x x 6 x x x x x 7 x x x x x x x 9 x x x x x x x x x x: Present_Value is writeable and not affected by inputs METZ CONNECT Im Tal 776 Blumberg Germany Phone +9 77 5- Fax +9 77 5- Distributed by IA CONNECT GmbH and BT NETCOM GmbH Mounting instruction see www.metz-connect.com