In case release and template are not assembled, mount them as indicated. Nel caso sganciatore e dima non siano assemblati, montarli come indicato. Im

Größe: px

Ab Seite anzeigen:

Download "In case release and template are not assembled, mount them as indicated. Nel caso sganciatore e dima non siano assemblati, montarli come indicato. Im"

Hilko Schreiber
vor 5 Jahren
Abrufe

1 0G-G-UVJ, 9G-UVKY, 0G-G-UVY, 0G-G-UVD, 0G-G-UVA, 0G-G-UVB, 0G-G-UVC Undervoltage release for 0G-G, 0G-H, 0G-I, 0G-J. Sganciatore di minima tensione Unterspannungsauslöser Déclencheur à minimum de tension Relé de minima tensión Bul. 0G/0MG Installation - Installazione - Instalación Instalação - - WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements). AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E). WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E). AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E). ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E). ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E). 警告 : 感電事故防止のため取付けまたは修理の際は電源から取り外してください適切なケース内に取付けてくださいまた汚染物質がないことを確認してください (NFPA70Eの要件に従ってください) 警告 : 为了防止触电, 在安装或维修之前必须先切断电源安装在合适的设备箱内防止接触污染物符合 NFPA70E 要求 ) Electrical diagram label Catalog number label UVR 80 0 V ~ UVR 80 V ~ Additional resistance present if necessary 0G-G 0G-I 0G-H 0G-J CLACK CLACK DIR 00079R00 Version 0

2 In case release and template are not assembled, mount them as indicated. Nel caso sganciatore e dima non siano assemblati, montarli come indicato. Im Fall Auslöser und Schablone nicht montiert sind, montieren sie als angezeigt. En cas déclencheur et gabarit ne soient assemblé, les assembler comme indiqué. En el caso relé y plantilla no estén ensamblado, ensemblarlos como indicado. 0G-G, 0G-I 0G-H, 0G-J CLICK DIR 00079R00 Version 0 ()

3 0G-I p ONLY 0G-G p ONLY FOR 0G-H, 0G-J p ONLY 7 FOR 0G-G,0G-I, 0G-H, 0G-J p ONLY After this - go to step (diagram) Optional DIR 00079R00 Version 0 ()

4 8 0G-G p ONLY, with UVR in p POCKET 9 0G-H, 0G-J p ONLY with UVR in p POCKET 0 p ONLY with UVR in p POCKET With 0 AWG/0. mm wires only, optional. p ONLY with UVR in p POCKET With 0 AWG/0. mm wires only,optional. DIR 00079R00 Version 0 ()

5 PUSH PULL 0G-H 0G-J 0G-G 0G-I 0G-G, 0G-I Apply labels 9.7 lb-in. Nm DIR 00079R00 Version 0 ()

6 0G-H, 0G-J CLICK 8 Apply labels 9.7 lb-in. Nm 7 DIR 00079R00 Version 0 ()

7 V 80...V(IEC) V(UL) V 80...V(IEC) V(UL) D 7 D D D V. lb-in 0.Nm 80...V(IEC) V(UL). lb-in 0.Nm UVR 80 V ~ UVR 80 0 V ~ ~ SO D 9.7 lb-in. Nm UVR D D D R ~ - Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Automation maintains current product environmental compliance information on its website at sustainability-ethics/product-environmental-compliance.page Publication 0G-IN078C-MU-P - September 0 DIR 00079R00 Version 0 (L990) - B00 Copyright 0 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.

Ähnliche Dokumente

Motor operator. insert

Motor operator. insert Bul. 40G/40MG DIR 00079R063 Version 0-40G-G-EOP_ Motor operator for 40G-G, 40G-I Comando a motore diretto cablato Motorantrieb mit Direktwirkung, verdrahtet Commande par moteur a action directe câblé Mando